Masonry heater

From Wikipedia, the free encyclopedia

A classic Scandinavian style round ceramic stove which fits in the corner of a room.

A masonry heater (or masonry stove, ceramic stove, tile stove) is a device for warming an interior space through radiant heating, by capturing the heat from periodic burning of fuel (usually wood), and then radiating the heat at a fairly constant temperature for a long period . The technology has existed in different forms, from back into the Neoglacial and Neolithic periods. Archeological digs have revealed excavations of ancient inhabitants utilizing hot smoke from fires in their subterranean dwellings, to radiate into the living spaces. These early forms have evolved into modern systems. Evidence found from 5,000 B.C. of massive blocks of masonry used to retain heat foreshadowed early forms of fire hearths that were used as multifunctional heating sources. Later evolutions came in the Roman hypocaust, Austrian/German kachelofen, baths) using the smoke and exhaust of a single fire. In Eastern and Northern Europe and North Asia, these kachelofens (or steinofens) evolved in many different forms and names: for example the Russian Stove/Fireplace (Russian: Русская печь), the Finnish Stove (in Finnish: pystyuuni or kaakeliuuni, "tile oven") and the Swedish Stove (in Swedish: kakelugn, "tile stove" or "contra-flow stove") associated with Carl Johan Cronstedt. The Chinese developed the same principle into their Kang bed-stove. The masonry heater has gained renewed domestic popularity recently because of its heating efficiency.

Characteristics

A kachelofen used for central heating, built around 1959.

The stove is made of masonry such as brick (firebrick), tile, stone, stucco, or a combination of materials, rather than steel or cast iron. It is freestanding, and usually requires special support to bear its weight. It consists of a firebox and heat-exchange channels or partitions that provide additional surface area. These absorb heat from the hot exhaust gases before the gases exit into the chimney. The fire in a masonry heater burns much hotter than in a metal stove. Very hot fires reduce emissions significantly. When not being fired, the connection from the masonry heater to the chimney sometimes has a damper to prevent heat from escaping up the chimney; the heat is then radiated from the masonry.

Masonry takes longer to heat than metal; but once warm, the heater will radiate this heat over a much longer period of time and at a much lower temperature than a metal stove would use (the metal is hot only when there is a fire burning inside the stove and for a short time thereafter). A masonry heater is warmed by fires that burn for a short time; it is mostly the heat stored by the heater's mass that heats the living space. Both in Europe and in America seating and even beds are occasionally built adjoining the masonry stove; this is possible because the heater's exterior surfaces are cool enough to touch safely.

Heat stress is a major concern during the construction of masonry heaters. Differences in temperature inside the masonry core of the heater can result in differential expansion. A skilled heater mason knows how to provide for this stress when designing and constructing the heater, thereby preventing uneven expansion from causing cracking in the exterior.

Masonry heaters take a long time (from 5 hours up to two days) to get up to the right temperature and so are not always practical for taking the chill off a single cool evening or morning, but they are well-suited for long periods of cold weather because they store heat so well and provide dependable, even heat all day and night. Because the radiant heat is given off at a low level a masonry heater is not likely to overheat a home the way a metal stove might in warmer parts of the year like fall or spring.

Kachelofen

The kachelofen design, a relatively large home heater surrounded with ceramic tile, has existed for at least five centuries. During the Renaissance period, the builders of kachelofens were part of a distinct trade and were called hafnermeisters. A kachelofen uses a maze-like passage created out of firebrick to release gases and smoke from the wood fire slowly, allowing the firebrick to retain as much heat as possible from the gases and smoke. The ceramic tile surrounding the kachelofen also acts as insulation to retain heat. Kachelofens were carefully designed so that the minimum amount of heat would escape, only as much as needed to warm the flue to maintain a proper air draught. The firebrick used in kachelofen construction holds 80% more heat than ferrous metals such as cast iron, while its heat conductivity is 1/45 that of iron or steel.^[1] A kachelofen is efficient enough to warm a house for up to 6 to 12 hours after the fire has stopped burning.^[2]

Fuel sources

Modern masonry heater

These heaters are primarily fired by wood, and those fires are meant to burn hot and quickly (never damped down, as is often the case with standard wood stoves). They are not burned continuously. This method of heating may have been a reaction to the dwindling resource of wood before the advent of coal and other mineral energy sources. Open hearth fireplaces were an important source of light, as well as heat, and with an "unlimited" supply of wood to fire them, there is no incentive to increase the efficiency of their heat output, which is rather poor. However, once firewood became a scarcer resource, fireplace builders began to enclose the firebox to capture as much heat as possible.

Since masonry heaters burn hot and fast, they can accept any dry, split (usually three to five inches in diameter) wood. In some areas of central and eastern Europe, these heaters are sometimes effectively fired using grass, straw, and hay. It is also common in eastern Europe to modify these efficient heaters so that they are connected to the gas network and are fueled with gas. Some modern models incorporate electric heating elements connected to timers. These are used only as a backup heat source during periods when the structure will be left unattended for long duration in winter (and therefore with no one to build a new fire in the heater each day or as needed) to prevent the structure from freezing.

Modern development

Some contemporary masonry heaters don't have a ceramic-tile exterior. Instead, the refractory bricks are covered by a heat-resistant kind of plaster. A glass door allows you to see the burning fire. As in the past once the firewood has burned, the warmed mass of the stove continues to radiate heat, but the size of the flue passages of modern masonry heaters are more exactly calculated than they used to be; this is done to provide increased efficiency and output and use less wood.

Gallery

References

↑ Schneider, Jason (January 1979). Tile stoves: efficient and elegant wood burners (Vol. 214, No. 1 ed.). Popular Science, Bonnier Corporation. p. 98. ISSN 0161-7370.
↑ Schneider, Jason (January 1979). Tile stoves: efficient and elegant wood burners (Vol. 214, No. 1 ed.). Popular Science, Bonnier Corporation. p. 100. ISSN 0161-7370.

External links

This article is issued from Wikipedia. The text is available under the Creative Commons Attribution/Share Alike; additional terms may apply for the media files.