I²S

I²S, also known as Inter-IC Sound, Integrated Interchip Sound, or IIS, is an electrical serial bus interface standard used for connecting digital audio devices together. It is used to communicate PCM audio data between integrated circuits in an electronic device. The I²S bus separates clock and serial data signals, resulting in a lower jitter than is typical of communications systems that recover the clock from the data stream.

History

This standard was introduced in 1986 by Philips (now NXP) and was last revised in 1996.

Details

The I²S protocol outlines one specific type of PCM digital audio communication with defined parameters outlined in the Philips specification.

The bit clock pulses once for each discrete bit of data on the data lines. The bit clock frequency is the product of the sample rate, the number of bits per channel and the number of channels. So, for example, CD Audio with a sample frequency of 44.1 kHz, with 16 bits of precision and two channels (stereo) has a bit clock frequency of:

44.1 kHz × 16 × 2 = 1.4112 MHz

The word select clock lets the device know whether channel 1 or channel 2 is currently being sent, since I²S allows two channels to be sent on the same data line. For stereo material, the I²S specification states that left audio is transmitted on the low cycle of the word select clock and the right channel is transmitted on the high cycle. The word select clock is a 50% duty-cycle signal that has the same frequency as the sample frequency.

Data are encoded in two's complement with the MSB (most significant bit) first.^[1]:2

The bus consists of at least three lines:

1. Bit clock line
2. Word clock line - also called word select (WS) or left right clock (LRCLK)
3. At least one multiplexed data line

It may also include the following lines:

1. Master clock (typical 256 x LRCLK)
2. A multiplexed data line for upload

In audio equipment the I²S is sometimes used as an external link between the CD transport and a separate DAC box, as opposed to purely internal connection within one player box. This could be used as an alternative to the commonly used AES/EBU or Toslink or S/PDIF standards. There is no standard interconnecting cable for this application. Some manufacturers provide simply three BNC connectors, an 8P8C ("RJ45") socket or a DE-9 connector. Others like Audio Alchemy (now defunct) used DIN connectors.

See also

• SPI bus

References

External links

• I²S Bus Specification at the Wayback Machine (archived July 2, 2006)
• I²S and STM32F4 Slides, Auburn University
• Common inter-IC digital interfaces for audio data transfer, PDF

v t e Computer bus — technical and de facto standards (wired) General System bus Front-side bus Back-side bus Daisy chain Control bus Address bus Bus contention Network on a chip Plug and play List of bus bandwidths Standards S-100 bus Unibus VAXBI MBus STD Bus SMBus Q-Bus ISA STEbus Zorro II Zorro III CAMAC FASTBUS LPC HP Precision Bus EISA VME VXI VXS NuBus TURBOchannel MCA SBus VLB PCI PXI HP GSC bus CoreConnect InfiniBand UPA PCI Extended (PCI-X) AGP PCI Express (PCIe) Direct Media Interface (DMI) RapidIO Intel QuickPath Interconnect HyperTransport Storage ST-506 ESDI SMD Parallel ATA (PATA) SSA DSSI HIPPI USB MSC IEEE 1394 interface (FireWire) Serial ATA (SATA) eSATA eSATAp mSATA SCSI Parallel SCSI SAS SATA Express M.2 Peripheral Apple Desktop Bus HIL MIDI Multibus RS-232 RS-422 RS-423 RS-485 DMX512-A IEEE-488 (GPIB) IEEE-1284 (parallel port) UNI/O ACCESS.bus 1-Wire D²B I²C SPI Parallel SCSI Profibus USB IEEE 1394 (FireWire) Camera Link External PCIe Thunderbolt Audio AC'97 I²S McASP S/PDIF TOSLINK ADAT Lightpipe AES3 MADI Portable PC Card ExpressCard Embedded Multidrop bus AMBA Wishbone Note: interfaces are listed in speed ascending order (roughly), the interface at the end of each section should be the fastest Category