Galileo (spacecraft)

Galileo

Artist's impression of Galileo flying past Io
Mission type	Jupiter orbiter
Operator	NASA
COSPAR ID	1989-084B
SATCAT №	20298
Website	www2.jpl.nasa.gov/galileo/
Mission duration	7.75 years
Spacecraft properties
Manufacturer	Jet Propulsion Laboratory
Launch mass	2,380 kilograms (5,250 lb) Probe: 339 kilograms (747 lb)
Power	Orbiter: 570 watts Probe: 580 watts
Start of mission
Launch date	October 18, 1989, 16:53:40 (1989-10-18UTC16:53:40Z) UTC
Rocket	Space Shuttle Atlantis STS-34 / IUS
Launch site	Kennedy Space Center LC-39B
Entered service	December 8, 1995[citation needed]
End of mission
Disposal	Deorbited
Decay date	September 21, 2003, 18:57:00 (2003-09-21UTC18:58Z) UTC
Orbital parameters
Reference system	Zenocentric
Flyby of Venus (gravity assist)
Closest approach	February 10, 1990
Flyby of Earth (gravity assist)
Closest approach	December 8, 1990
Flyby of 7002951000000000000(951) Gaspra (incidental)
Closest approach	October 29, 1991
Flyby of Earth (gravity assist)
Closest approach	December 8, 1992
Flyby of 7002243000000000000(243) Ida (incidental)
Closest approach	August 28, 1993
Jupiter atmospheric probe
Spacecraft component	Probe
Atmospheric entry	December 7, 1995, 22:04 UTC Operated for 57 minutes
Impact site	6.5°N, 4.4°W at entry interface
Jupiter orbiter
Spacecraft component	Orbiter
Orbital insertion	December 8, 1995, 01:20:00 UTC

Galileo was serendipitously positioned to view Comet Shoemaker–Levy 9's impact with Jupiter. These images, taken several seconds apart, show fragment W colliding (1994)

Galileo was an unmanned NASA spacecraft which studied the planet Jupiter and its moons, as well as several other solar system bodies. Named after the astronomer Galileo Galilei, it consisted of an orbiter and entry probe. It was launched on October 18, 1989, carried by Space Shuttle Atlantis, on the STS-34 mission. Galileo arrived at Jupiter on December 7, 1995, after gravitational assist flybys of Venus and Earth, and became the first spacecraft to orbit Jupiter. It launched the first probe into Jupiter, directly measuring its atmosphere.^[1] Despite suffering major antenna problems, Galileo achieved the first asteroid flyby, of 951 Gaspra, and discovered the first asteroid moon, Dactyl, around 243 Ida. In 1994, Galileo observed Comet Shoemaker–Levy 9's collision with Jupiter.^[1]

Jupiter's atmospheric composition and ammonia clouds were recorded, the clouds possibly created by outflows from the lower depths of the atmosphere. Io's volcanism and plasma interactions with Jupiter's atmosphere was also recorded. The data Galileo collected supported the theory of a liquid ocean under the icy surface of Europa, and there were indications of similar liquid-saltwater layers under the surfaces of Ganymede and Callisto. Ganymede was shown to possess a magnetic field and the spacecraft found new evidence for exospheres around Europa, Ganymede, and Callisto.^[1] Galileo also discovered that Jupiter's faint ring system consists of dust from impacts on the four small inner moons. The extent and structure of Jupiter's magnetosphere was also mapped.^[1]

On September 21, 2003, after 14 years in space and 8 years in the Jovian system, Galileo's mission was terminated by sending the orbiter into Jupiter's atmosphere at a speed of over 48 kilometers (30 mi) per second, eliminating the possibility of contaminating local moons with terrestrial bacteria.

On December 11, 2013, NASA reported, based on results from the Galileo mission, the detection of "clay-like minerals" (specifically, phyllosilicates), often associated with organic materials, on the icy crust of Europa, moon of Jupiter.^[2] The presence of the minerals may have been the result of a collision with an asteroid or comet according to the scientists.^[2]

Mission overview

Galileo launching

Galileo shot of Earth's Moon

A false-color mosaic constructed from a series of 53 images taken through three spectral filters by Galileo' s imaging system as the spacecraft flew over the northern regions of the Moon on December 7, 1992.

Work on the spacecraft began at JPL in 1977, while the Voyager 1 and 2 missions were still being prepared for launch. Early plans called for a launch on Space Shuttle Columbia on what was then codenamed STS-23 in January 1982, but delays in the development of the Space Shuttle allowed more time for development of the probe. As the shuttle program got underway, Galileo was scheduled for launch in 1984, but this later slipped to 1985 and then to 1986.^[3] The mission was initially called the Jupiter Orbiter Probe; it was christened Galileo in 1978.^[4]

Once the spacecraft was complete, its launch was scheduled for STS-61-G on-board Atlantis in 1986. The Inertial Upper Stage booster was going to be used at first, but this changed to the Centaur booster, then back to IUS after Challenger.^[3]

The Centaur-G liquid hydrogen-fueled booster stage allowed a direct trajectory to Jupiter. However, the mission was further delayed by the hiatus in launches that occurred after the Space Shuttle Challenger disaster. New safety protocols introduced as a result of the disaster prohibited the use of the Centaur-G stage on the Shuttle, forcing Galileo to use a lower-powered Inertial Upper Stage solid-fuel booster. The mission was re-profiled in 1987 to use several gravitational slingshots, referred to as the "VEEGA" or Venus Earth Earth Gravity Assist maneuvers, to provide the additional velocity required to reach its destination.

It was finally launched on October 18, 1989, by the Space Shuttle Atlantis on the STS-34 mission.

Venus was flown by at 05:58:48 UT on February 10, 1990 at a range of 16,106 km. Having gained 8,030 km per hour in speed, the spacecraft flew by Earth twice, the first time at a range of 960 km at 20:34:34 UT on 8 December 1990 before approaching the minor planet 951 Gaspra to a distance of 1,604 km at 22:37 UT on 29 October 1991. Galileo then performed a second flyby of Earth at 303.1 km at 15:09:25 UT on 8 December 1992, adding 3.7 km per second to its cumulative speed. Galileo performed close observation of a second asteroid, 243 Ida, at 16:51:59 UT on 28 August 1993 at a range of 2,410 km. The spacecraft discovered Ida has a moon Dactyl, the first discovery of a natural satellite orbiting an asteroid. In 1994, Galileo was perfectly positioned to watch the fragments of the comet Shoemaker-Levy 9 crash into Jupiter, whereas terrestrial telescopes had to wait to see the impact sites as they rotated into view. After releasing its atmospheric probe on 13 July 1995, the Galileo orbiter became the first man-made satellite of Jupiter at 00:27 UT on 8 December 1995 when it fired its main engine to enter a 198-day parking orbit.^[5]

Amalthea

Galileo's prime mission was a two-year study of the Jovian system. The spacecraft traveled around Jupiter in elongated ellipses, each orbit lasting about two months. The differing distances from Jupiter afforded by these orbits allowed Galileo to sample different parts of the planet's extensive magnetosphere. The orbits were designed for close-up flybys of Jupiter's largest moons. Once the prime mission concluded, an extended mission started on December 7, 1997; the spacecraft made a number of flybys of Europa and Io. The closest approach was 180 km (110 mi) on October 15, 2001. The radiation environment near Io was very unhealthy for Galileo's systems, and so these flybys were saved for the extended mission when loss of the spacecraft would be more acceptable.

Galileo's cameras were deactivated on January 17, 2002, after they had sustained irreparable radiation damage. NASA engineers were able to recover the damaged tape recorder electronics, and Galileo continued to return scientific data until it was deorbited in 2003, performing one last scientific experiment —a measurement of the moon Amalthea's mass as the spacecraft swung by it.

Spacecraft

The Jet Propulsion Laboratory built the Galileo spacecraft and managed the Galileo mission for NASA. Germany supplied the propulsion module. NASA's Ames Research Center managed the probe, which was built by Hughes Aircraft Company.

Galileo with its main antenna open

At launch, the orbiter and probe together had a mass of 2,564 kilograms (5,653 pounds) and stood seven metres tall. One section of the spacecraft rotated at 3 rpm, keeping Galileo stable and holding six instruments that gathered data from many different directions, including the fields and particles instruments. The other section of the spacecraft was an antenna, and data were periodically transmitted to it. Back on the ground, the mission operations team used software containing 650,000 lines of programming code in the orbit sequence design process; 1,615,000 lines in the telemetry interpretation; and 550,000 lines of code in navigation.

Command and Data Handling (CDH)

The CDH subsystem was actively redundant, with two parallel data system buses running at all times.^[6] Each data system bus (aka string) was composed of the same functional elements, consisting of multiplexers (MUX), high-level modules (HLM), low-level modules (LLM), power converters (PC), bulk memory (BUM), data management subsystem bulk memory (DBUM), timing chains (TC), phase locked loops (PLL), Golay coders (GC), hardware command decoders (HCD) and critical controllers (CRC).

The CDH subsystem was responsible for maintaining the following functions:

1. decoding of uplink commands
2. execution of commands and sequences
3. execution of system-level fault-protection responses
4. collection, processing, and formatting of telemetry data for downlink transmission
5. movement of data between subsystems via a data system bus

The spacecraft was controlled by six RCA 1802 COSMAC microprocessor CPUs: four on the spun side and two on the despun side. Each CPU was clocked at about 1.6 MHz, and fabricated on sapphire (silicon on sapphire), which is a radiation-and static-hardened material ideal for spacecraft operation. This microprocessor was the first low-power CMOS processor chip, quite on a par with the 8-bit 6502 that was being built into the Apple II desktop computer at that time. Galileo's attitude control system software was written in the HAL/S programming language, also used in the Space Shuttle program.

Memory capacity provided by each BUM was 16K of RAM, while the DBUMs each provided 8K of RAM. There were two BUMs and two DBUMs in the CDH subsystem and they all resided on the spun side of the spacecraft. The BUMs and DBUMs provided storage for sequences and contain various buffers for telemetry data and interbus communication.

Every HLM and LLM was built up around a single 1802 microprocessor and 32K of RAM (for HLMs) or 16K of RAM (for LLMs). Two HLMs and two LLMs resided on the spun side while two LLMs were on the despun side.

Thus, total memory capacity available to the CDH subsystem was 176K of RAM: 144K allocated to the spun side and 32K to the despun side.

Each HLM was responsible for the following functions:

1. uplink command processing
2. maintenance of the spacecraft clock
3. movement of data over the data system bus
4. execution of stored sequences (time-event tables)
5. telemetry control
6. error recovery including system fault-protection monitoring and response

Each LLM was responsible for the following functions:

1. collect and format engineering data from the subsystems
2. provide the capability to issue coded and discrete commands to spacecraft users
3. recognize out-of-tolerance conditions on status inputs
4. perform some system fault-protection functions

The HCD receives command data from the modulation/demodulation subsystem, decodes these data and transfers them to the HLMs and CRCs.

The CRC controls the configuration of CDH subsystem elements. It also controls access to the two data system buses by other spacecraft subsystems. In addition, the CRC supplies signals to enable certain critical events (e.g. probe separation).

The GCs provide Golay encoding of data via hardware.

The TCs and PLLs establish timing within the CDH subsystem.

Propulsion

Galileo captures a dynamic eruption at Tvashtar Catena, a chain of volcanic bowls on Jupiter's moon Io.

The Propulsion Subsystem consisted of a 400 N main engine and twelve 10 N thrusters, together with propellant, storage and pressurizing tanks and associated plumbing. The 10 N thrusters were mounted in groups of six on two 2-meter booms. The fuel for the system was 925 kg of monomethylhydrazine and nitrogen tetroxide. Two separate tanks held another 7 kg of helium pressurant. The Propulsion Subsystem was developed and built by Daimler Benz Aero Space AG (DASA) (formerly Messerschmitt–Bölkow–Blohm (MBB)) and provided by Germany, the major international partner in Project Galileo.^[7]

Electrical power

At the time, Solar panels were not practical at Jupiter's distance from the Sun (it would have needed a minimum of 65 square meters (700 sq ft) of solar panels). Chemical batteries would likewise be prohibitively massive due to the technological limitations. The solution was two radioisotope thermoelectric generators (RTGs) which powered the spacecraft through the radioactive decay of plutonium-238. The heat emitted by this decay was converted into electricity through the solid-state Seebeck effect. This provided a reliable and long-lasting source of electricity unaffected by the cold environment and high-radiation fields in the Jovian system.

Each GPHS-RTG, mounted on a 5-meter long boom, carried 7.8 kilograms (17.2 lb) of ²³⁸Pu.^[8] Each RTG contained 18 separate heat source modules, and each module encased four pellets of plutonium dioxide, a ceramic material resistant to fracturing. The modules were designed to survive a range of hypothetical accidents: launch vehicle explosion or fire, re-entry into the atmosphere followed by land or water impact, and post-impact situations. An outer covering of graphite provided protection against the structural, thermal, and eroding environments of a potential re-entry. Additional graphite components provided impact protection, while iridium cladding of the fuel cells provided post-impact containment. The RTGs produced about 570 watts at launch. The power output initially decreased at the rate of 0.6 watts per month and was 493 watts when Galileo arrived at Jupiter.

A diagram of Galileo's main components.

As the launch of Galileo neared, anti-nuclear groups, concerned over what they perceived as an unacceptable risk to the public's safety from Galileo's RTGs, sought a court injunction prohibiting Galileo's launch. RTGs had been used for years in planetary exploration without mishap: the Lincoln Experimental Satellites 8/9, launched by the U.S. Department of Defense, had 7% more plutonium on board than Galileo, and the two Voyager spacecraft each carried 80% as much plutonium as Galileo did. However, activists remembered the messy crash of the Soviet Union's nuclear-powered Cosmos 954 satellite in Canada in 1978, and though was not nuclear-powered, the 1986 Challenger accident raised public awareness about spacecraft failures. In addition, no RTGs had ever done a non-orbital swing past the Earth at close range and high speed, as Galileo's Venus-Earth-Earth Gravity Assist trajectory required it to do. This created a novel mission failure modality that might plausibly have entailed total dispersal of Galileo's plutonium in the Earth's atmosphere. Scientist Carl Sagan, for example, a strong supporter of the Galileo mission, said in 1989 that "there is nothing absurd about either side of this argument." ^[9]

After Challenger, a study considered additional shielding but rejected it, in part because such a design significantly increased the overall risk of mission failure and only shifted the other risks around (for example, if a failure on orbit had occurred, additional shielding would have significantly increased the consequences of a ground impact).^[8]

Instrumentation overview

Jovian "Hotspot" in visible (top) and near infrared (bottom)

Scientific instruments to measure fields and particles were mounted on the spinning section of the spacecraft, together with the main antenna, power supply, the propulsion module and most of Galileo's computers and control electronics. The sixteen instruments, weighing 118 kg altogether, included magnetometer sensors mounted on an 11 m boom to minimize interference from the spacecraft; a plasma instrument for detecting low-energy charged particles and a plasma-wave detector to study waves generated by the particles; a high-energy particle detector; and a detector of cosmic and Jovian dust. It also carried the Heavy Ion Counter, an engineering experiment added to assess the potentially hazardous charged particle environments the spacecraft flew through, and an added Extreme Ultraviolet detector associated with the UV spectrometer on the scan platform.

The despun section's instruments included the camera system; the near infrared mapping spectrometer to make multi-spectral images for atmospheric and moon surface chemical analysis; the ultraviolet spectrometer to study gases; and the photo-polarimeter radiometer to measure radiant and reflected energy. The camera system was designed to obtain images of Jupiter's satellites at resolutions from 20 to 1,000 times better than Voyager's best, because Galileo flew closer to the planet and its inner moons, and because the more modern CCD sensor in Galileo's camera was more sensitive and had a broader color detection band than the vidicons of Voyager.

Instrumentation details

The following information was taken directly from NASA's Galileo legacy site.^[10]

Despun section

Detailed diagram of Galileo' s instruments and subsystems (click to enlarge).

Solid State Imager (SSI)

The spacecraft's Solid-State Imager.

The SSI was an 800-by-800-pixel solid state camera consisting of an array of silicon sensors called a "charge coupled device" (CCD). Galileo was one of the first spacecraft to be equipped with a CCD camera.^{[citation needed]} The optical portion of the camera was built as a Cassegrain telescope. Light was collected by the primary mirror and directed to a smaller secondary mirror that channeled it through a hole in the center of the primary mirror and onto the CCD. The CCD sensor was shielded from radiation, a particular problem within the harsh Jovian magnetosphere. The shielding was accomplished by means of a 10 mm thick layer of tantalum surrounding the CCD except where the light enters the system. An eight-position filter wheel was used to obtain images at specific wavelengths. The images were then combined electronically on Earth to produce color images. The spectral response of the SSI ranged from about 0.4 to 1.1 micrometres. The SSI weighed 29.7 kilograms and consumed, on average, 15 watts of power.^[11][12]

Near-Infrared Mapping Spectrometer (NIMS)

The NIMS instrument was sensitive to 0.7-to-5.2-micrometre wavelength IR light, overlapping the wavelength range of the SSI. The telescope associated with NIMS was all reflective (using only mirrors and no lenses) with an aperture of 229 mm. The spectrometer of NIMS used a grating to disperse the light collected by the telescope. The dispersed spectrum of light was focused on detectors of indium antimonide and silicon. The NIMS weighed 18 kilograms and used 12 watts of power on average.^[13][14]

Ultraviolet Spectrometer / Extreme Ultraviolet Spectrometer (UVS/EUV)

Ultraviolet Spectrometer

The Cassegrain telescope of the UVS had a 250 mm aperture and collected light from the observation target. Both the UVS and EUV instruments used a ruled grating to disperse this light for spectral analysis. This light then passed through an exit slit into photomultiplier tubes that produced pulses or "sprays" of electrons. These electron pulses were counted, and these count numbers constituted the data that were sent to Earth. The UVS was mounted on Galileo's scan platform and could be pointed to an object in inertial space. The EUV was mounted on the spun section. As Galileo rotated, EUV observed a narrow ribbon of space perpendicular to the spin axis. The two instruments combined weighed about 9.7 kilograms and used 5.9 watts of power.^[15][16]

Photopolarimeter-Radiometer (PPR)

The PPR had seven radiometry bands. One of these used no filters and observed all incoming radiation, both solar and thermal. Another band allowed only solar radiation through. The difference between the solar-plus-thermal and the solar-only channels gave the total thermal radiation emitted. The PPR also measured in five broadband channels that spanned the spectral range from 17 to 110 micrometres. The radiometer provided data on the temperatures of Jupiter's atmosphere and satellites. The design of the instrument was based on that of an instrument flown on the Pioneer Venus spacecraft. A 100 mm aperture reflecting telescope collected light and directed it to a series of filters, and, from there, measurements were performed by the detectors of the PPR. The PPR weighed 5.0 kilograms and consumed about 5 watts of power.^[17][18]

Spun section

Dust Detector Subsystem (DDS)

The Dust Detector Subsystem (DDS) was used to measure the mass, electric charge, and velocity of incoming particles. The masses of dust particles that the DDS could detect go from 10⁻¹⁶ to 10⁻⁷ grams. The speed of these small particles could be measured over the range of 1 to 70 kilometers per second. The instrument could measure impact rates from 1 particle per 115 days (10 megaseconds) to 100 particles per second. Such data was used to help determine dust origin and dynamics within the magnetosphere. The DDS weighed 4.2 kilograms and used an average of 5.4 watts of power.^[19][20]

Energetic Particles Detector (EPD)

The Energetic Particles Detector (EPD) was designed to measure the numbers and energies of ions and electrons whose energies exceeded about 20 keV (3.2 fJ). The EPD could also measure the direction of travel of such particles and, in the case of ions, could determine their composition (whether the ion is oxygen or sulfur, for example). The EPD used silicon solid state detectors and a time-of-flight detector system to measure changes in the energetic particle population at Jupiter as a function of position and time. These measurements helped determine how the particles got their energy and how they were transported through Jupiter's magnetosphere. The EPD weighed 10.5 kilograms and used 10.1 watts of power on average.^[21][22]

Heavy Ion Counter (HIC)

Galileo' s Heavy Ion Counter.

The HIC was in effect a repackaged and updated version of some parts of the flight spare of the Voyager Cosmic Ray System. The HIC detected heavy ions using stacks of single crystal silicon wafers. The HIC could measure heavy ions with energies as low as 6 MeV (1 pJ) and as high as 200 MeV (32 pJ) per nucleon. This range included all atomic substances between carbon and nickel. The HIC and the EUV shared a communications link and, therefore, had to share observing time. The HIC weighed 8 kilograms and used an average of 2.8 watts of power.^[23][24]

Magnetometer (MAG)

The magnetometer (MAG) used two sets of three sensors. The three sensors allowed the three orthogonal components of the magnetic field section to be measured. One set was located at the end of the magnetometer boom and, in that position, was about 11 m from the spin axis of the spacecraft. The second set, designed to detect stronger fields, was 6.7 m from the spin axis. The boom was used to remove the MAG from the immediate vicinity of Galileo to minimize magnetic effects from the spacecraft. However, not all these effects could be eliminated by distancing the instrument. The rotation of the spacecraft was used to separate natural magnetic fields from engineering-induced fields. Another source of potential error in measurement came from the bending and twisting of the long magnetometer boom. To account for these motions, a calibration coil was mounted rigidly on the spacecraft to generate a reference magnetic field during calibrations. The magnetic field at the surface of the Earth has a strength of about 50,000 nT. At Jupiter, the outboard (11 m) set of sensors could measure magnetic field strengths in the range from ±32 to ±512 nT, while the inboard (6.7 m) set was active in the range from ±512 to ±16,384 nT. The MAG experiment weighed 7 kilograms and used 3.9 watts of power.^[25][26]

The Plasma Wave Subsystem.

Plasma Subsystem (PLS)

The PLS used seven fields of view to collect charged particles for energy and mass analysis. These fields of view covered most angles from 0 to 180 degrees, fanning out from the spin axis. The rotation of the spacecraft carried each field of view through a full circle. The PLS measured particles in the energy range from 0.9 eV to 52 keV (0.1 aJ to 8.3 fJ). The PLS weighed 13.2 kilograms and used an average of 10.7 watts of power.^[27][28]

Plasma Wave Subsystem (PWS)

An electric dipole antenna was used to study the electric fields of plasmas, while two search coil magnetic antennas studied the magnetic fields. The electric dipole antenna was mounted at the tip of the magnetometer boom. The search coil magnetic antennas were mounted on the high-gain antenna feed. Nearly simultaneous measurements of the electric and magnetic field spectrum allowed electrostatic waves to be distinguished from electromagnetic waves. The PWS weighed 7.1 kilograms and used an average of 9.8 watts.^[29][30]

Galileo Probe

Artist's impression of the probe's entry into Jupiter's atmosphere

The descent module

Timeline of the probe's atmospheric entry.

The Galileo Probe was an atmospheric-entry probe carried by the main spacecraft to Jupiter, where it directly entered and returned data from the planet.^[31] The 339-kilogram (747 lb) probe was built by Hughes Aircraft Company^[32] at its El Segundo, California plant, measured about 1.3 meters (4.3 ft) across. Inside the probe's heat shield, the scientific instruments were protected from extreme heat and pressure during its high-speed journey into the Jovian atmosphere, travelling at 47.8 kilometers (29.7 mi) per second.

The probe was released from the main spacecraft in July 1995, five months before reaching Jupiter, and entered Jupiter's atmosphere with no braking beforehand. The probe was slowed from its arrival speed of about 47 kilometers per second to subsonic speed in less than two minutes.

At the time, this was by far the most difficult atmospheric entry ever attempted; the probe had to withstand 230 g^[33] and the probe's 152 kg heat shield, making up almost half of the probe's total mass, lost 80 kg during the entry.^[34][35] NASA built a special laboratory, the Giant Planet Facility, to simulate the heat load, which was similar to the convective heating experienced by an ICBM warhead reentering the atmosphere combined with the radiative heating of a thermonuclear fireball.^[36][37] It then deployed its 2.5-meter (8 ft) parachute, and dropped its heat shield, which fell into Jupiter's interior.

As the probe descended through 156 kilometres (97 mi)^[31] of the top layers of the Jovian atmosphere, it collected 58 minutes of data on the local weather. It only stopped transmitting when the ambient pressure exceeded 23 atmospheres and the temperature reached 153 °C (307 °F).^[38] The data was sent to the spacecraft overhead, then transmitted back to Earth. Each of 2 L-band transmitters operated at 128 bits per second and sent nearly identical streams of scientific data to the orbiter. All the probe's electronics were powered by lithium sulfur dioxide (LiSO₂) batteries that provided a nominal power output of about 580 watts with an estimated capacity of about 21 ampere-hours on arrival at Jupiter. The probe included six instruments for taking data on its plunge into Jupiter:

• an atmospheric structure instrument group measuring temperature, pressure and deceleration,
• a neutral mass spectrometer,
• a helium-abundance interferometer supporting atmospheric composition studies,
• a nephelometer for cloud location and cloud-particle observations,
• a net-flux radiometer measuring the difference between upward and downward radiant flux at each altitude, and
• a lightning/radio-emission instrument with an energetic-particle detector that measured light and radio emissions associated with lightning and energetic particles in Jupiter's radiation belts.

Total data returned from the probe was about 3.5 megabits (~460,000 bytes). The probe stopped transmitting before the line of sight link with the orbiter was cut. The likely proximal cause of the final probe failure was overheating, which sensors indicated before signal loss.

The atmosphere through which the probe descended was somewhat hotter and more turbulent than expected. The probe was eventually completely destroyed as it continued to descend through the molecular hydrogen layer beneath the Jovian cloud tops. The parachute would have melted first, roughly 30 minutes after entry,^[39] then the aluminum components after another 40 minutes of free fall through a sea of supercritical fluid hydrogen. The titanium structure would have lasted around 6.5 hours more before disintegrating. Due to the high pressure, the droplets of metals from the probe would finally have vaporized once their critical temperature had been reached, and mixed with Jupiter's liquid metallic hydrogen interior.

Jupiter was found to have half the amount of helium expected.^[31] Also, the data did not support the three-cloud layer theory.^[31] It detected less lightning, less water, but more winds than expected; consistent 530 kilometers per hour (330 mph) winds during its descent.^[31] No solid surface was detected during its journey downward to 156 kilometres (97 mi).^[31]

Jupiter science

Pwyll crater on Europa.

Terrain on Ganymede. This region is about 213 by 97 km (132 by 60 miles.)^[1]

After arriving on December 7, 1995 and completing 35 orbits around Jupiter throughout a nearly eight-year mission, the Galileo Orbiter was destroyed during a controlled impact with Jupiter on September 21, 2003. During that intervening time, Galileo forever changed the way scientists saw Jupiter and provided a wealth of information on the moons orbiting the planet which will be studied for years to come. Culled from NASA's press kit, the top orbiter science results were:

• Galileo made the first observation of ammonia clouds in another planet's atmosphere. The atmosphere creates ammonia ice particles from material coming up from lower depths.
• The moon Io was confirmed to have extensive volcanic activity that is 100 times greater than that found on Earth. The heat and frequency of eruptions are reminiscent of early Earth.
• Complex plasma interactions in Io's atmosphere create immense electrical currents which couple to Jupiter's atmosphere.
• Several lines of evidence from Galileo support the theory that liquid oceans exist under Europa's icy surface.
• Ganymede possesses its own, substantial magnetic field - the first satellite known to have one.
• Galileo magnetic data provide evidence that Europa, Ganymede and Callisto have a liquid-saltwater layer under the visible surface.
• Evidence exists that Europa, Ganymede, and Callisto all have a thin atmospheric layer known as a 'surface-bound exosphere'.
• Jupiter's ring system is formed by dust kicked up as interplanetary meteoroids smash into the planet's four small inner moons. The outermost ring is actually two rings, one embedded with the other. There is probably a separate ring along Amalthea's orbit, as well.
• The Galileo spacecraft identified the global structure and dynamics of a giant planet's magnetosphere.

Other science conducted by Galileo

Star scanner

Galileo' s star scanner was a small optical telescope that provided an absolute attitude reference. It also made several scientific discoveries serendipitously.^[40] In the prime mission, it was found that the star scanner was able to detect high-energy particles as a noise signal. These data were eventually calibrated to show the particles were predominantly >2 MeV electrons that were trapped in the Jovian magnetic belts.

A second discovery occurred in 2000. The star scanner was observing a set of stars which included the second magnitude star Delta Velorum. At one point, this star dimmed for 8 hours below the star scanner's detection threshold. Subsequent analysis of Galileo data and work by amateur and professional astronomers showed that Delta Velorum is the brightest known eclipsing binary, brighter at maximum than even Algol.^[41] It has a primary period of 45 days and the dimming is just visible with the naked eye.

A final discovery occurred during the last two orbits of the mission. When the spacecraft passed the orbit of Jupiter's moon Amalthea, the star scanner detected unexpected flashes of light that were reflections from moonlets. None of the individual moonlets were sighted twice, hence no orbits were determined and the moonlets did not meet the International Astronomical Union requirements to receive designations.^[42] It is believed that these moonlets most likely are debris ejected from Amalthea and form a tenuous, and perhaps temporary, ring.

Remote detection of life on Earth

Galileo image of Earth, taken in December 1990

The cosmologist Carl Sagan, pondering the question of whether life on Earth could be easily detected from space, devised a set of experiments in the late 1980s using Galileo' s remote sensing instruments during the mission's first Earth flyby in December 1990. After data acquisition and processing, Sagan et al. published a paper in Nature in 1993 detailing the results of the experiment. Galileo had indeed found what are now referred to as the "Sagan criteria for life". These included strong absorption of light at the red end of the visible spectrum (especially over continents) which was caused by absorption by chlorophyll in photosynthesizing plants, absorption bands of molecular oxygen which is also a result of plant activity, infrared absorption bands caused by the ~1 micromole per mole (µmol/mol) of methane in Earth's atmosphere (a gas which must be replenished by either volcanic or biological activity), and modulated narrowband radio wave transmissions uncharacteristic of any known natural source. Galileo' s experiments were thus the first ever controls in the newborn science of astrobiological remote sensing. ^[43]

The Galileo optical experiment

An image of Earth taken by Galileo during the GOPEX test, showing laser pulses coming from a transmitting telescope on the night side. Galileo's imager was panned downward during the exposure to separate the pulses, thus blurring Earth's image on the right.

In December 1992, during Galileo' s second gravity-assist planetary flyby of Earth, another groundbreaking experiment was performed. Optical communications in space was assesed by detecting light pulses from powerful lasers with Galileo' s CCD. The experiment, dubbed Galileo OPtical EXperiment or GOPEX,^[44] used two separate sites to beam laser pulses to the spacecraft, one at Table Mountain Observatory in California and the other at the Starfire Optical Range in New Mexico. The Table Mountain site used a frequency doubled Neodymium-Yttrium-Aluminium Garnet (Nd:YAG) laser operating at 532 nm with a repetition rate of ~15 to 30 Hz and a pulse power (FWHM) in the tens of megawatts range, which was coupled to a 0.6 meter Cassegrain telescope for transmission to Galileo; the Starfire range site used a similar setup with a larger transmitting telescope (1.5 m). Long exposure (~0.1 to 0.8 s) images using Galileo's 560 nm centered green filter produced images of Earth clearly showing the laser pulses even at distances of up to 6,000,000 km. Adverse weather conditions, restrictions placed on laser transmissions by the U.S. Space Defense Operations Center (SPADOC) and a pointing error caused by the scan platform acceleration on the spacecraft being slower than expected (which prevented laser detection on all frames with less than 400 ms exposure times) all contributed to the reduction of the number of successful detections of the laser transmission to 48 of the total 159 frames taken. Nonetheless, the experiment was considered a resounding success and the data acquired will likely be used in the future to design laser "downlinks" which will send large volumes of data very quickly, from spacecraft to Earth. The scheme is already being studied (as of 2004) for a data link to a future Mars orbiting spacecraft.^[45]

Asteroid encounters

951 Gaspra (enhanced colorization).

First asteroid encounter: 951 Gaspra

On October 29, 1991, two months after entering the asteroid belt, Galileo performed the first asteroid encounter by a human spacecraft, passing approximately 1,600 kilometers (990 mi) from 951 Gaspra at a relative speed of about 8 kilometers per second (18,000 mph). Several pictures of Gaspra were taken, along with measurements using the NIMS instrument to indicate composition and physical properties. The last two images were relayed back to Earth in November 1991 and June 1992. The imagery revealed a cratered and very irregular body, measuring about 19 by 12 by 11 kilometers (12 by 7.5 by 7 miles). The remainder of data taken, including low-resolution images of more of the surface, were transmitted in late November 1992.^[46]

Second asteroid encounter: 243 Ida and Dactyl

243 Ida. The bright dot to the right is its moon, Dactyl.

On August 28, 1993, Galileo flew within 2,400 kilometers (1,500 mi) of the asteroid 243 Ida. The probe discovered that Ida had a small moon, dubbed Dactyl, measuring around 1.4 kilometers (0.87 mi) in diameter; this was the first asteroid moon discovered. Measurements using Galileo's solid state imager, magnetometer and NIMS instrument were taken. From subsequent analysis of this data, Dactyl appears to be an SII subtype S type asteroid, and is spectrally different from 243 Ida. It is hypothesized that Dactyl may have been produced by partial melting within a Koronis parent body, while the 243 Ida region escaped such igneous processing.

Spacecraft malfunctions and anomalies

Main antenna failure

Laboratory tests verified that holding ribs 9, 10, and 11 in the stowed position most closely modeled the spacecraft's telemetry.

Galileo' s high-gain antenna failed to fully deploy after its first flyby of Earth. The antenna had 18 ribs, like an umbrella and when the driver motor started and put pressure on the ribs, they were supposed to pop out of the cup their tips were held in. Only 15 popped out, leaving the antenna looking like a lop-sided, half-open umbrella. Investigators concluded that during the 4.5 years that Galileo spent in storage after the 1986 Challenger disaster, the lubricants between the tips of the ribs and the cup evaporated and no one thought to renew them. Engineers tried thermal-cycling the antenna, rotating the spacecraft up to its maximum spin rate of 10.5 rpm, and "hammering" the antenna deployment motor — turning it on and off repeatedly — over 13,000 times, but all attempts failed to open the high-gain antenna. The associated problem mission managers faced was if one rib popped free, there would be increased pressure on the remaining two, and if one of them popped out the last would be under so much pressure it would never release. The second part of the problem was due to Galileo's revised flight plan. The probe had never been intended to approach the sun any closer than the orbit of Earth, but sending it to Venus would expose it to temperatures at least 50 degrees higher than at Earth distance. So the probe had to be protected from that extra heat, part of which protection which involved adapting some of the computer functions. Forty-one drivers had been programmed into the computer, with no room for any more, and mission planners had to decide which driver they could use in association with the heat protection. They chose the antenna motor reverse driver. Even with the dry grease at the antenna rib tips, had the antenna motor been able to run backwards, as well as forwards, the ribs would have eventually popped out.

Artist's concept of Galileo at Io; note the fully deployed high-gain antenna. Compare with below image.

Artist's concept of Galileo at Jupiter with its high-gain antenna only partially deployed.

Fortunately, Galileo possessed an additional low-gain antenna that was capable of transmitting information back to Earth, although since it transmitted a signal isotropically, the low-gain antenna's bandwidth was significantly less than the high-gain antenna's would have been; the high-gain antenna was to have transmitted at 134 kilobits per second, whereas the low-gain antenna was only intended to transmit at about 8 to 16 bits per second. Galileo' s low-gain antenna transmitted with a power of about 15 to 20 watts, which, by the time it reached Earth, and had been collected by one of the large aperture (70 m) DSN antennas, had a total power of about -170 dBm or 10 zeptowatts (10 × 10⁻²¹ watts).^[47] Through the implementation of sophisticated technologies, the arraying of several Deep Space Network antennas and sensitivity upgrades to the receivers used to listen to Galileo' s signal, data throughput was increased to a maximum of 160 bits per second.^[48] By further using data compression, the effective data rate could be raised to 1,000 bits per second.^[48][49] The data collected on Jupiter and its moons was stored in the spacecraft's onboard tape recorder, and transmitted back to Earth during the long apozene portion of the probe's orbit using the low-gain antenna. At the same time, measurements were made of Jupiter's magnetosphere and transmitted back to Earth. The reduction in available bandwidth reduced the total amount of data transmitted throughout the mission, although 70% of Galileo' s science goals could still be met.^[50]

Tape recorder anomalies and remote repair

The failure of Galileo' s high-gain antenna meant that data storage to the tape recorder for later compression and playback was absolutely crucial in order to obtain any substantial information from the flybys of Jupiter and its moons. In October 1995, Galileo' s four-track, 114-megabyte^[51] digital tape recorder, which was manufactured by Odetics Corporation, remained stuck in rewind mode for 15 hours before engineers learned what had happened and sent commands to shut it off. Though the recorder itself was still in working order, the malfunction possibly damaged a length of tape at the end of the reel. This section of tape was subsequently declared "off limits" to any future data recording, and was covered with 25 more turns of tape to secure the section and reduce any further stresses, which could tear it. Because it happened only weeks before Galileo entered orbit around Jupiter, the anomaly prompted engineers to sacrifice data acquisition of almost all of the Io and Europa observations during the orbit insertion phase, in order to focus solely on recording data sent from the Jupiter probe descent.

In November 2002, after the completion of the mission's only encounter with Jupiter's moon Amalthea, problems with playback of the tape recorder again plagued Galileo. About 10 minutes after the closest approach of the Amalthea flyby, Galileo stopped collecting data, shut down all of its instruments, and went into safe mode, apparently as a result of exposure to Jupiter's intense radiation environment. Though most of the Amalthea data was already written to tape, it was found that the recorder refused to respond to commands telling it to play back data. After weeks of troubleshooting of an identical flight spare of the recorder on the ground, it was determined that the cause of the malfunction was a reduction of light output in three infrared Optek OP133 light emitting diodes located in the drive electronics of the recorder's motor encoder wheel. The GaAs LEDs had been particularly sensitive to proton-irradiation-induced atomic lattice displacement defects, which greatly decreased their effective light output and caused the drive motor's electronics to falsely believe the motor encoder wheel was incorrectly positioned. Galileo' s flight team then began a series of "annealing" sessions, where current was passed through the LEDs for hours at a time to heat them to a point where some of the crystalline lattice defects would be shifted back into place, thus increasing the LED's light output. After about 100 hours of annealing and playback cycles, the recorder was able to operate for up to an hour at a time. After many subsequent playback and cooling cycles, the complete transmission back to Earth of all recorded Amalthea flyby data was successful.

Near-failure of atmospheric probe parachute

The parachute for the entry probe is tested on Earth

The atmospheric probe deployed its first parachute about one minute later than anticipated, resulting in a small loss of upper atmospheric readings. Through review of records, the problem was later determined to likely be faulty wiring in the parachute control system. The fact that the chute opened at all was attributed to luck.^[52] It is now believed that the accelerometer controlling the parachute's pyrotechnics was installed backwards. A similar defect affected the Genesis probe's sample return capsule when it returned to Earth in September 2004, causing the capsule to crash in the Utah desert.^[53]

Other radiation-related anomalies

Jupiter's uniquely harsh radiation environment caused over 20 anomalies over the course of Galileo's mission, in addition to the incidents expanded upon above. Despite exceeding its radiation design limit by at least a factor of three, the spacecraft survived all these anomalies – work-arounds were found eventually for all of these problems, and Galileo was never rendered entirely non-functional by Jupiter's radiation. The radiation limits for Galileo's computers were based off data returned from Pioneers 10 and 11, since much of the design work was underway before the two Voyagers arrived at Jupiter in 1979.^[54]

A typical effect of the radiation was that several of the science instruments suffered increased noise while within about 700,000 kilometres (430,000 mi) of Jupiter. The SSI camera began producing totally white images when the spacecraft was hit by the exceptional 'Bastille Day' coronal mass ejection in 2000, and did so again on subsequent close approaches to Jupiter. The quartz crystal used as the frequency reference for the radio suffered permanent frequency shifts with each Jupiter approach. A spin detector failed, and the spacecraft gyro output was biased by the radiation environment.

The most severe effect of the radiation were current leakages somewhere in spacecraft's power bus, most likely across brushes at a spin bearing connecting rotor and stator sections of the orbiter. These current leakages triggered a reset of the onboard computer and caused it to go into safe mode. The resets occurred when the spacecraft was either close to Jupiter or in the region of space magnetically downstream of the Earth. A change to the software was made in April 1999 that allowed the onboard computer to detect these resets and autonomously recover, so as to avoid safe mode.^[55]

End of mission and deorbit

Years of Jupiter's intense radiation took its toll on the spacecraft systems, and its fuel supply was running low in the early 2000s. Galileo had not been sterilized, so to prevent forward contamination of its moons, a plan was formulated to send it directly into Jupiter. So Galileo was intentionally commanded to crash into Jupiter, which eliminated the possibility it would impact Europa and seed it with bacteria.

In order to crash into Jupiter, Galileo flew by Amalthea on November 5, 2002,^[56] during its 34th orbit, allowing a measurement of the moon's mass as it passed within 163.0 kilometers (101.3 mi) ± 11.7 kilometers (7.3 mi) of its surface. On April 14, 2003, Galileo reached its greatest distance from Jupiter for the entire mission prior to orbital insertion, 26,000,000 kilometers (16,000,000 mi), before plunging back towards the gas giant for its final impact.^[57] At the completion of its 35th and final circuit around the Jovian system, Galileo impacted the gas giant in darkness just south of the equator on September 21, 2003, at 18:57 GMT. Its impact speed was approximately 173,736 kilometres per hour (107,955 mph).^[58] The total mission cost was about US$1.4 billion.^[59][60]

The four largest moons of Jupiter, as imaged by Galileo.

See also

• Exploration of Jupiter
• Cassini–Huygens, Saturn orbiter

References

External links

Wikimedia Commons has media related to Galileo mission.

• Galileo home page
• Galileo Mission Profile by NASA's Solar System Exploration
• Galileo Satellite Image Mosaics
• Site explaining the LGA bandwidth upgrades from the Parkes Observatory
• GOPEX site from JPL
• NASA site on Galileo life detection experiments
• Mission to Jupiter: a History of the Galileo Project, by Michael Meltzer, NASA SP 2007-4231 (on-line book)
• Exploring the Moon: Galileo Mission
• JPL guide to Galileo Telecommunications
• Gallery of Jupiter system photos, including some by Galileo
• View of Europa from Galileo flybys

v t e Spacecraft missions to Jupiter Orbiters Galileo Juno (en route) Descent probes Galileo Probe Flybys Pioneer 10 Pioneer 11 Voyager 1 Voyager 2 Ulysses Cassini–Huygens New Horizons Planned missions Jupiter Icy Moon Explorer (2022) Proposed flybys Argo New Horizons 2 Innovative Interstellar Explorer Uranus Orbiter Jupiter and Trojan asteroid exploration Proposed missions Europa Clipper Europa Jupiter System Mission-Laplace Jupiter Europa Orbiter Jupiter Ganymede Orbiter Jupiter Magnetospheric Orbiter Europa Lander Io Volcano Observer Cancelled missions Europa Orbiter Jupiter Icy Moons Orbiter Neptune Orbiter Jovian Europa Orbiter Pioneer H Tsiolkovsky mission Related topics Deep Space Network Exploration of Io Moons of Jupiter Italics indicates active missions, even if they passed Jupiter already.

v t e Spacecraft missions to Venus Flybys Venera 1 Mariner 2 Zond 1 Venera 2 Mariner 5 Mariner 10 Venera 11 Venera 12 Venera 13 Venera 14 Vega 1 Vega 2 Galileo Cassini–Huygens MESSENGER IKAROS Shin-en Akatsuki (intended as an orbiter) Orbiters Venera 9 Venera 10 Pioneer Venus Orbiter Venera 15 Venera 16 Magellan Venus Express Descent probes Venera 3 Venera 4 Venera 5 Venera 6 Pioneer Venus Multiprobe Landers Venera 7 Venera 8 Kosmos 482 (failed) Venera 9 Venera 10 Venera 11 Venera 12 Venera 13 Venera 14 Vega 1 Vega 2 Pioneer Venus Small Probes Balloon probes Vega 1 Vega 2 Planned and proposed Venera-D Venus Entry Probe Venus In-Situ Explorer Cancelled Manned Venus Flyby TMK-Mavr See also Colonization of Venus Observations and explorations of Venus List of artificial objects on Venus Italics indicates active missions