FlexRay

From Wikipedia, the free encyclopedia

FlexRay is an automotive network communications protocol developed by the FlexRay Consortium to govern on-board automotive computing. It is designed to be faster and more reliable than CAN and TTP, but it is also more expensive. The FlexRay consortium disbanded in 2009. The FlexRay standard is now a set of ISO standards ISO 17458-1 to 17458-5 [1]

Features

FlexRay's prominent features are:

  • High data rates (up to 10 Mbit/s)
  • Time- and event-triggered behavior
  • Redundancy
  • Fault-tolerance
  • Deterministic

Consortium

The FlexRay Consortium was made up of the following core members:

There were also Premium Associate and Associate members of FlexRay consortium. By September 2009, there were 28 premium associate members and more than 60 associate members. At the end of 2009, the consortium disbanded.

Where used

The first series production vehicle with FlexRay was at the end of 2006 in the BMW X5, enabling a new and fast adaptive damping system. Full use of FlexRay was introduced in 2008 in the new BMW 7 Series (F01).

Vehicles

Details

Clock

FlexRay system consists of a bus and processors (Electronic control unit, or ECUs). Each ECU has an independent clock. The clock drift must be not more than 0.15% from the reference clock, so the difference between the slowest and the fastest clock in the system is no greater than 0.3%.

This means that, if ECU-s is a sender and ECU-r is a receiver, then for every 300 cycles of the sender there will be between 299 and 301 cycles of the receiver. The clocks are resynchronized frequently enough to assure that this causes no problems. Clock is sent in static segment.[3]

Bits on the bus

0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0

Correct averaging in case of no errors. The signal is merely delayed by 2 cycles.

0 0 0 0 0 0 1 1 1 1 0 1 1 1 0 0 0 0
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0

Errors near the middle of 8-cycle region are canceled.

0 0 0 1 0 1 1 1 1 1 1 1 1 0 0 0 0
0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0

Errors near the boundary of 8-cycle region may affect the boundary bit.

At each time, only one ECU writes to the bus. Each bit to be sent is held on the bus for 8 sample clock cycles. The receiver keeps a buffer of the last 5 samples, and uses the majority of the last 5 samples as the input signal.

Single-cycle transmission errors may affect results near the boundary of the bits, but will not affect cycles in the middle of the 8-cycle region.

Sampled bits

The value of the bit is sampled in the middle of the 8-bit region. The errors are moved to the extreme cycles, and the clock is synchronized frequently enough for the drift to be small. (Drift is smaller than 1 cycle per 300 cycles, and during transmission the clock is synchronized more than once every 300 cycles).

Frame

All the communication is sent in the form of frames. The message consists of bytes \{x_{0},x_{1},\dots ,x_{{m-1}}\}, packed in the following way:

  • Transmission Start Signal (TSS) – bit 0
  • Frame Start Signal (FSS) – bit 1
  • m times:
    • Byte Start Signal 0 (BSS0) – bit 1
    • Byte Start Signal 1 (BSS1) – bit 0
    • 0-th bit of i-th byte
    • 1-st bit of i-th byte
    • 2-nd bit of i-th byte
    • ...
    • 7-th bit of i-th byte
  • Frame End Signal (FES) – bit 0
  • Transmission End Signal (TES) – bit 1

If nothing is being communicated, the bus is held in state 1 (high voltage), so every receiver knows that the communication started when the voltage drops to 0.

The receiver knows when the message is complete by checking whether BSS0 (1) or FES (0) was received.

Note that 8-cycle per bit has nothing to do with bytes. Each byte takes 80 cycles to transfer. 16 for BSS0 and BSS1 and 64 for its bits. Also note that BSS0 has value 1, and BSS1 has value 0.

Clock synchronization

Clocks are resynchronized when the voted signal changes from 1 to 0, if the receiver was in either idle state or expecting BSS1.

So the clock is synchronized when the transmission starts and between BSS0 and BSS1. As synchronization is done on the voted signal, small transmission errors during synchronization that affect the boundary bits may skew the synchronization no more than 1 cycle. As there are at most 88 cycles between synchronization (BSS1, 8 bits of the last byte, FES and TES - 11 bits of 8 cycles each), and the clock drift is no larger than 1 per 300 cycles, the drift may skew the clock no more than 1 cycle. Small transmission errors during the receiving may affect only the boundary bits. So in the worst case the two middle bits are correct, and thus the sampled value is correct.

Here's an example of a particularly bad case - error during synchronization, a lost cycle due to clock drift and error in transmission.

Errors that happened in the example

  • Because of a single-bit error during synchronization, the synchronization was delayed by 1 cycle
  • Receiver clock was slower than sender clock, so receiver missed one cycle (marked X). This will not happen again before the next synchronization due to limits on maximum allowable clock drift.
  • Because of a single-bit error during transmission, a bit was voted wrongly near the result.

Despite so many errors, the communication was received correctly.

The green cells are sampling points. All except the first are synchronized by the 1->0 edge in the transmission fragment shown.

Signal to be sent 1 0 1 0 1
Signal sent 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1
On the bus 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 0 1 1
Received 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 1 1 1 1 1 1 X 1 0 0 0 0 0 0 1 0 1 1
5-maj voted 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 X 1 1 1 0 0 0 0 0 0 0 1


Development tools

When developing and/or troubleshooting the FlexRay bus, examination of hardware signals can be very important. Logic analyzers and bus analyzers are tools which collect, analyze, decode, store signals so people can view the high-speed waveforms at their leisure.

The future of FlexRay

The bus has certain disadvantages like lower operating voltage levels and asymmetry of the edges, which leads to problems in extending the network length. Ethernet may replace FlexRay for bandwidth intensive, non-safety critical applications.[4]

See also

References

  1. ↑ The FlexRay Electrical Physical Layer Evolution; Automotive 2010.
  2. ↑ "2011 Audi A8 4.2 FSI First Drive". Retrieved 18 February 2010. 
  3. ↑ http://www.eberspaecher-electronics.com/en/company/flexray-introduction.html#c62713
  4. ↑ http://www.eetimes.com/document.asp?doc_id=1256700. Retrieved 21 July 2013.  Missing or empty |title= (help)

External links


Computer bus — technical and de facto standards (wired)
General
Standards
Storage
Peripheral
Audio
Portable
Embedded
Note: interfaces are listed in speed ascending order (roughly), the interface at the end of each section should be the fastest
Category
Process automation
Industrial control system
Building automation
Power system automation
Automatic meter reading
Automobile / Vehicle
This article is issued from Wikipedia. The text is available under the Creative Commons Attribution/Share Alike; additional terms may apply for the media files.