Combination square

From Wikipedia, the free encyclopedia

Combination square with standard head

A combination square consisting of the ruler, 45° holder, protractor and center square

A combination square is a tool used for multiple purposes in woodworking, stonemasonry and metalworking. It is composed of a ruled blade and one or more interchangeable heads that may be affixed to it.^[1] The most common head is the standard or square head which is used to lay out or check right and 45° angles.^[1]

Uses

Measuring angles — A combination square can reliably measure 90° and 45° angles. The 45° angle is used commonly in creating miter joints.
Determining flatness — When working with wood the first step is to designate a reference surface on a board which is known as the face side. The rest of the workpiece is measured from the face side
Measuring the center of a circular bar or dowel. The rule is assembled through the center of the center square, the two cast iron legs of the center square are then placed against the outside of the bar (dowel) allowing a center line to be scribed alongside the ruler. Perform this action at two locations and the intersecting lines will approximate the center of the bar (dowel).
Protractor head allows angles to be set and measured between the base and ruler.
A rudimentary level for approximating level surfaces is incorporated in the protractor and also the 45° holder.
By moving and setting the head, it can be used as a depth gauge or to transfer dimensions.
Marking the work surface; with the included Scribe Point stored in a drilled hole in the Square Base.

In woodworking, the starting raw material is neither flat nor square, however, the end product such as a table must be flat and have corners and legs which are square.

In metalworking, it is useful for a wide variety of layout and setup tasks. When used correctly, a fairly high degree of precision can be achieved. One use would be setting large items at the required angle in machine vices, where the long reach of the ruler and firm, heavy base aid the process.

Invented by Laroy S. Starrett in 1878, the combination square continues to be a commonplace tool in home workshops, construction jobsites and metalworking

References

↑ 1.0 1.1 Campbell, Paul D. Q. (1995). An introduction to measuration and calibration. Industrial Press Inc. ISBN 978-0-8311-3060-2.

Metalworking

Tools

Cutting machines	Bandsaw Cold saw Laser Miter saw Plasma Water jet cutter

Cutting tools	Broach Burr Chisel Counterbore Countersink End mill File Hand scraper Milling cutter Nibbler Reamer Shears Tipped tool Tool bit

Forming tools	Brake Die English wheel Hydraulic press Machine press Punch press Screw press Stamping press

Hand tools	Clamp Combination square Drift pin Hacksaw Hammer Hand scraper Machinist square Needlegun scaler Piercing saw Pliers Punch Scriber Tap and die Tongs Vise Workbench Wrench

Machine tooling	Angle plate Chuck Collet Fixture Indexing head Jig Lathe center Machine taper Magnetic base Mandrel Rotary table Wiggler

Measuring instruments	Bore gauge Caliper Center gauge Dial indicator Engineer's blue Engineer's spirit level Feeler gauge Gauge Gauge block Go/no go gauge Height gauge Machinist square Marking blue Marking gauge Marking out Micrometer Optical comparator Radius gauge Ruler Sine bar Straightedge Surface plate Tape measure Thread pitch gauge Vernier scale

Smithing tools	Anvil Forge Fuller Hardy tools Pritchel Steam hammer Swage block Trip hammer

v t e Measuring and alignment tools

architect's scale beam compass caliper chalk box combination square compass coordinate-measuring machine drafting machine engineer's scale flat spline jig laser level laser line level laser measuring tool lesbian rule micrometer plumb-bob protractor ruler set square sliding T bevel spirit level steel square stencil straightedge T-square tape measure theodolite vise weighing scale yardstick

Types of tools Cleaning Cutting and abrasive Forestry and gardening Hand Machine and metalworking Measuring and alignment Power

This article is issued from Wikipedia. The text is available under the Creative Commons Attribution/Share Alike; additional terms may apply for the media files.