| Part of a series on the |
| History of printing |
|---|
| Woodblock printing (200) |
| Movable type (1040) |
| Printing press (1454) |
| Etching (ca. 1500) |
| Mezzotint (1642) |
| Aquatint (1768) |
| Lithography (1796) |
| Chromolithography (1837) |
| Rotary press (1843) |
| Offset printing (1875) |
| Hectograph (19th century) |
| Hot metal typesetting (1886) |
| Mimeograph (1890) |
| Screen printing (1907) |
| Spirit duplicator (1923) |
| Dye-sublimation (1957) |
| Phototypesetting (1960s) |
| Dot matrix printer (1964) |
| Laser printing (1969) |
| Thermal printing (ca. 1972) |
| Inkjet printing (1976) |
| Stereolithography (1986) |
| Digital press (1993) |
| 3D printing (ca. 2003) |
Screen printing is a printing technique that uses a woven mesh to support an ink-blocking stencil. The attached stencil forms open areas of mesh that transfer ink or other printable materials which can be pressed through the mesh as a sharp-edged image onto a substrate. A roller or squeegee is moved across the screen stencil, forcing or pumping ink past the threads of the woven mesh in the open areas.
Screen printing is also a stencil method of print making in which a design is imposed on a screen of silk or other fine mesh, with blank areas coated with an impermeable substance, and ink is forced through the mesh onto the printing surface. It is also known as silkscreen, serigraphy, and serigraph printing.
Contents |
There are various terms used for what is essentially the same technique. Traditionally the process was called screen printing or silkscreen printing because silk was used in the process. Currently, synthetic threads are commonly used in the screen printing process. The most popular mesh in general use is made of polyester. There are special-use mesh materials of nylon and stainless steel available to the screen printer.
Encyclopedia references, encyclopedias and trade publications also use an array of spellings for this process with the two most often encountered English spellings as, screenprinting spelled as a single undivided word, and the more popular two word title of screen printing without hyphenation.
Screen printing first appeared in a recognizable form in China during the Song Dynasty (960–1279 AD).[1][2] Japan and other Asian countries adopted this method of printing and advanced the craft using it in conjunction with block printing and hand applied paints.
Screen printing was largely introduced to Western Europe from Asia sometime in the late 18th century, but did not gain large acceptance or use in Europe until silk mesh was more available for trade from the east and a profitable outlet for the medium discovered.
Screen printing was first patented in England by Samuel Simon in 1907.[2][3] It was originally used as a popular method to print expensive wall paper, printed on linen, silk, and other fine fabrics. Western screen printers developed reclusive, defensive and exclusionary business policies intended to keep secret their workshops' knowledge and techniques.[4]
Early in the 1910s, several printers experimenting with photo-reactive chemicals used the well-known actinic light activated cross linking or hardening traits of potassium, sodium or ammonium Chromate and dichromate chemicals with glues and gelatin compounds. Roy Beck, Charles Peter and Edward Owens studied and experimented with chromic acid salt sensitized emulsions for photo-reactive stencils. This trio of developers would prove to revolutionize the commercial screen printing industry by introducing photo-imaged stencils to the industry, though the acceptance of this method would take many years. Commercial screen printing now uses sensitizers far safer and less toxic than bichromates. Currently there are large selections of pre-sensitized and "user mixed" sensitized emulsion chemicals for creating photo-reactive stencils.[4]
Joseph Ulano founded the industry chemical supplier Ulano and in 1928 created a method of applying a lacquer soluble stencil material to a removable base. This stencil material was cut into shapes, the print areas removed and the remaining material adhered to mesh to create a sharp edged screen stencil.[5]
Originally a profitable industrial technology, screen printing was eventually adopted by artists as an expressive and conveniently repeatable medium for duplication well before the 20th century. It is currently popular both in fine arts and in commercial printing, where it is commonly used to print images on Posters, T-shirts, hats, CDs, DVDs, ceramics, glass, polyethylene, polypropylene, paper, metals, and wood.
A group of artists who later formed the National Serigraphic Society coined the word Serigraphy in the 1930s to differentiate the artistic application of screen printing from the industrial use of the process.[6] "Serigraphy" is a combination word from the Latin word "Seri" (silk) and the Greek word "graphein" (to write or draw).[7]
The Printer's National Environmental Assistance Center says "Screenprinting is arguably the most versatile of all printing processes."[8] Since rudimentary screenprinting materials are so affordable and readily available, it has been used frequently in underground settings and subcultures, and the non-professional look of such DIY culture screenprints have become a significant cultural aesthetic seen on movie posters, record album covers, flyers, shirts, commercial fonts in advertising, in artwork and elsewhere.
Credit is generally given to the artist Andy Warhol for popularizing screen printing identified as serigraphy, in the United States. Warhol is particularly identified with his 1962 depiction of actress Marilyn Monroe screen printed in garish colors.[9][10]
| Artist | Andy Warhol |
|---|---|
| Year | 1962 |
| Type | Acrylic on canvas |
| Dimensions | 205.44 cm × 289.56 cm (80.88 in × 114.00 in) |
| Location | Tate Gallery, London |
American entrepreneur, artist and inventor Michael Vasilantone would start to use, develop, and sell a rotary multicolor garment screen printing machine in 1960. Vasilantone would later file for patent[11] on his invention in 1967 granted number 3,427,964 on February 18, 1969.[11] The original rotary machine was manufactured to print logos and team information on bowling garments but soon directed to the new fad of printing on t-shirts. The Vasilantone patent was licensed by multiple manufacturers, the resulting production and boom in printed t-shirts made the rotary garment screen printing machine the most popular device for screen printing in the industry. Screen printing on garments currently accounts for over half of the screen printing activity in the United States.[12]
In June 1986, Marc Tartaglia, Marc Tartaglia Jr. and Michael Tartaglia created a silk screening device which is defined in its US Patent Document as, "Multi-colored designs are applied on a plurality of textile fabric or sheet materials with a silk screen printer having seven platens arranged in two horizontal rows below a longitudinal heater which is movable across either row." This invention received the patent number 4,671,174 on June 9, 1987, however the patent no longer exists.
Graphic screenprinting is widely used today to create many mass or large batch produced graphics, such as posters or display stands. Full color prints can be created by printing in CMYK (cyan, magenta, yellow and black ('key')). Screenprinting is often preferred over other processes such as dye sublimation or inkjet printing because of its low cost and ability to print on many types of media.
Screen printing lends itself well to printing on canvas. Andy Warhol, Rob Ryan, Blexbolex, Arthur Okamura, Robert Rauschenberg, Harry Gottlieb, and many other artists have used screen printing as an expression of creativity and artistic vision.
A screen is made of a piece of porous, finely woven fabric called mesh stretched over a frame of aluminium or wood. Originally human hair was used, then silk was woven to make a screen mesh; currently most mesh is woven of man-made materials such as steel, nylon, and polyester. Areas of the screen are blocked off with a non-permeable material to form a stencil, which is a negative of the image to be printed; that is, the open spaces are where the ink will appear.
Before ink is applied to the screen, the screen and frame must go through a process referred to as 'pre-press'. In this process, an emulsion is 'scooped' across the mesh and the 'exposure unit' burns away the unnecessary emulsion leaving behind a clean area in the mesh with the identical shape as the desired image. The surface (commonly referred to as a pallet) that the substrate will be printed against is coated with a wide 'pallet tape'. This serves to protect the 'pallet' from any unwanted ink leaking through the substrate and potentially staining the 'pallet' or transferring unwanted ink onto the next substrate. Next, the screen and frame are lined with a tape. The type of tape used in for this purpose often depends upon the ink that is to be printed onto the substrate. These aggressive tapes are generally used for UV and water-based inks due to the inks' lower viscosities. The last process in the 'pre-press' is blocking out any unwanted 'pin-holes' in the emulsion. If these holes are left in the emulsion, the ink will continue through and leave unwanted marks. To block out these holes, materials such as tapes, specialty emulsions and 'block-out pens' may be used effectively.
The screen is placed atop a substrate such as paper or fabric. Ink is placed on top of the screen, and a fill bar (also known as a floodbar) is used to fill the mesh openings with ink. The operator begins with the fill bar at the rear of the screen and behind a reservoir of ink. The operator lifts the screen to prevent contact with the substrate and then using a slight amount of downward force pulls the fill bar to the front of the screen. This effectively fills the mesh openings with ink and moves the ink reservoir to the front of the screen. The operator then uses a squeegee (rubber blade) to move the mesh down to the substrate and pushes the squeegee to the rear of the screen. The ink that is in the mesh opening is pumped or squeezed by capillary action to the substrate in a controlled and prescribed amount, i.e. the wet ink deposit is proportional to the thickness of the mesh and or stencil. As the squeegee moves toward the rear of the screen the tension of the mesh pulls the mesh up away from the substrate (called snap-off) leaving the ink upon the substrate surface.
There are three common types of screenprinting presses. The 'flat-bed', 'cylinder', and the most widely used type, the 'rotary'.[8]
Textile items printed with multi-colour designs often use a wet on wet technique, or colors dried while on the press, while graphic items are allowed to dry between colours that are then printed with another screen and often in a different color after the product is re-aligned on the press.
The screen can be re-used after cleaning. However if the design is no longer needed, then the screen can be "reclaimed"; that is, cleared of all emulsion and used again. The reclaiming process involves removing the ink from the screen then spraying on a stencil remover. Stencil removers come in the form of liquids, gels, or powders. The powdered types have to be mixed with water before use, and so can be considered to belong to the liquid category. After applying the stencil remover, the emulsion must be washed out using a pressure washer.
Most screens are ready for recoating at this stage, but sometimes screens will have to undergo a further step in the reclaiming process called dehazing. This additional step removes haze or "ghost images" left behind in the screen once the emulsion has been removed. Ghost images tend to faintly outline the open areas of previous stencils, hence the name. They are the result of ink residue trapped in the mesh, often in the knuckles of the mesh (the points where threads cross).[13]
While the public thinks of garments in conjunction with screenprinting, the technique is used on tens of thousands of items, including decals, clock and watch faces, balloons, and many other products. The technique has even been adapted for more advanced uses, such as laying down conductors and resistors in multi-layer circuits using thin ceramic layers as the substrate.
There are several ways to create a stencil for screenprinting. An early method was to create it by hand in the desired shape, either by cutting the design from a non-porous material and attaching it to the bottom of the screen, or by painting a negative image directly on the screen with a filler material which became impermeable when it dried. For a more painterly technique, the artist would choose to paint the image with drawing fluid, wait for the image to dry, and then coat the entire screen with screen filler. After the filler had dried, water was used to spray out the screen, and only the areas that were painted by the drawing fluid would wash away, leaving a stencil around it. This process enabled the artist to incorporate their hand into the process, to stay true to their drawing.
A method that has increased in popularity over the past 70 years is the photo emulsion technique:
Photographic screens can reproduce images with a high level of detail, and can be reused for tens of thousands of copies. The ease of producing transparent overlays from any black-and-white image makes this a convenient method for artists. Artists can obtain screens, frames, emulsion, and lights separately; there are also preassembled kits, which are especially popular for printing small items such as greeting cards.
Another advantage of screenprinting is that large quantities can be produced rapidly with new automatic presses, up to 1800 shirts in 1 hour.[14] The current speed loading record is 1805 shirts printed in one hour, documented on 18 February 2005. Maddie Sikorski of the New Buffalo Shirt Factory in Clarence, New York (USA) set this record at the Image Wear Expo in Orlando, Florida, USA, using a 12-colour M&R Formula Press and an M&R Passport Automatic Textile Unloader. The world speed record represents a speed that is over four times the typical average speed for manual loading of shirts for automated screen printing.[12]
Screenprinting is more versatile than traditional printing techniques. The surface does not have to be printed under pressure, unlike etching or lithography, and it does not have to be planar. Different inks can be used to work with a variety of materials, such as textiles, ceramics, wood, paper, glass, metal, and plastic. As a result, screenprinting is used in many different industries, including:
In screen printing on wafer-based solar photovoltaic (PV) cells, the mesh and buses of silver are printed on the front; furthermore, the buses of silver are printed on the back. Subsequently, aluminum paste is dispensed over the whole surface of the back for passivation and surface reflection.[15] One of the parameters that can vary and can be controlled in screen printing is the thickness of the print. This makes it useful for some of the techniques of printing solar cells, electronics etc.
One of the most critical processes to maintain high yield. Solar wafers are becoming thinner and larger, so careful printing is required to maintain a lower breakage rate. On the other hand, high throughput at the printing stage improves the throughput of the whole cell production line.[15]
Traditionally, production garment decoration has relied on screen printing for printing designs on garments including t-shirts; recently, new methods and technologies have become available. Digital printing directly onto garments using modified consumer-quality, and task-specific designed inkjet printers. Screen printing, however, has remained an attractive, cost-effective, and high production-rate method of printing designs onto garments. Digital printing directly onto garments is referred to as DTG or DTS representing Direct To Garment or Direct To Shirt. DTG or DTS direct printing has advantages and disadvantages compared to screen printing. One noted advantage of DTG/DTS is number of visually perceived colors and the obvious photo-reproduction and photo-like print. DTG/DTS is often WYSIWYG (an acronym for What You See Is What You Get), whereas screen printing often requires skilled artistic modification and then must be photo reproduced onto screens and printed. DTG/DTS has the advantage of quick one-off designs and small quantity orders where the screen printing process involves several independent time consuming steps. Screen printing is a production method and quickly overtakes DTG/DTS in cost per print as the higher the volume the lower cost per print becomes, screen printing also has the advantage of a large selection of different types of inks that are all considerably less expensive per garment than DTG/DTS inks.
To print multiple copies of the screen design on garments in an efficient manner, amateur and professional printers usually use a screen printing press. Many companies offer simple to sophisticated printing presses. Most of these presses are manual. A few that are industrial-grade-automatic printers require minimal manual labor and increase production significantly.