Scramjet

Scramjet
Part of a series on
Aircraft propulsion
Shaft engines :
driving propellers, rotors, ducted fans, or propfans
Reaction engines
Others

A scramjet (supersonic combustion ramjet) is a variant of a ramjet airbreathing jet engine in which combustion takes place in supersonic airflow. As in ramjets, a scramjet relies on high vehicle speed to forcefully compress and decelerate the incoming air before combustion (hence ramjet), but whereas a ramjet decelerates the air to subsonic velocities before combustion, airflow in a scramjet is supersonic throughout the entire engine. This allows the scramjet to efficiently operate at extremely high speeds: theoretical projections place the top speed of a scramjet between Mach 12 and Mach 24, which is near orbital velocity. The fastest air-breathing aircraft is a SCRAM jet design, the NASA X-43A which reached Mach 9.8. For comparison, the second fastest[1] air-breathing aircraft, the manned SR-71 Blackbird, has a cruising speed of Mach 3.2.[2]

The scramjet is composed of three basic components: a converging inlet, where incoming air is compressed and decelerated; a combustor, where gaseous fuel is burned with atmospheric oxygen to produce heat; and a diverging nozzle, where the heated air is accelerated to produce thrust. Unlike a typical jet engine, such as a turbojet or turbofan engine, a scramjet does not use rotating, fan-like components to compress the air; rather, the achievable speed of the aircraft moving through the atmosphere causes the air to compress within the inlet. As such, no moving parts are needed in a scramjet. In comparison, typical turbojet engines require inlet fans, multiple stages of rotating compressor fans, and multiple rotating turbine stages, all of which add weight, complexity, and a greater number of failure points to the engine.

Due to the nature of their design, scramjet operation is limited to near-hypersonic velocities. As they lack mechanical compressors, scramjets require the high kinetic energy of a hypersonic flow to compress the incoming air to operational conditions. Thus, a scramjet-powered vehicle must be accelerated to the required velocity by some other means of propulsion, such as turbojet, railgun, or rocket engines.[3] In the flight of the experimental scramjet-powered Boeing X-51A, the test craft was lifted to flight altitude by a Boeing B-52 Stratofortress before being released and accelerated by a detachable rocket to near Mach 4.5.[4]

While scramjets are conceptually simple, actual implementation is limited by extreme technical challenges. Hypersonic flight within the atmosphere generates immense drag, and temperatures found on the aircraft and within the engine can be much greater than that of the surrounding air. Maintaining combustion in the supersonic flow presents additional challenges, as the fuel must be injected, mixed, ignited, and burned within milliseconds. While scramjet technology has been under development since the 1950s, only very recently have scramjets successfully achieved powered flight.[5]

Contents

History

During and after World War II, tremendous amounts of time and effort were put into researching high-speed jet- and rocket-powered aircraft. The Bell X-1 attained supersonic flight in 1947 and, by the early 1960s, rapid progress towards faster aircraft suggested that operational aircraft would be flying at "hypersonic" speeds within a few years. Except for specialized rocket research vehicles like the North American X-15 and other rocket-powered spacecraft, aircraft top speeds have remained level, generally in the range of Mach 1 to Mach 3.

In the 1950s and 1960s a variety of experimental scramjets engines were built and ground tested in US and the UK. In 1964, Dr. Frederick S. Billig and Dr. Gordon L. Dugger submitted a patent application for a supersonic combustion ramjet based on Billig’s Ph.D. thesis. This patent was issued in 1981 following the removal of an order of secrecy.[6]

In 1981 tests were made in Australia under the guidance of Professor Ray Stalker in the T3 ground test facility at ANU.[7]

First successful flight test of Scramjet was performed by Russia in 1991. It was axisymmetric hydrogen-fueled dual-mode scramjet developed by Central Institute of Aviation Motors (CIAM), Moscow from late 1970s. The scramjet flight was flown captive-carry atop the SA-5 surface-to-air missile that included an experiment flight support unit known as the "Hypersonic Flying Laboratory" (HFL), “Kholod”.[8] Then during the period since 1992 up to 1998 an additional 6 flight tests of the axisymmetric high-speed scramjet-demonstrator were conducted by CIAM together with France and then with NASA, USA.[9][10] Maximum flight velocity greater than Mach 6.4 was achieved and Scramjet operation during 77 seconds was demonstrated. These flight test series also provided insight into autonomous hypersonic flight controls.

Investigations of hypersonic flight have continued over the past few decades. At present, the US military and NASA have formulated a "National Hypersonics Strategy" to investigate a range of options for hypersonic flight.

Different U.S. organizations have accepted hypersonic flight as a common goal. The U.S. Army desires hypersonic missiles that can attack mobile missile launchers quickly. NASA believes hypersonics could help develop economical, reusable launch vehicles. The Air Force is interested in a range of hypersonic systems, from air-launched cruise missiles to orbital spaceplanes, that the service believes could bring about a true "aerospace force."

The problem is complicated by the release of previously classified material and by partial publication, where claims are made, but specific parts of an experiment are kept secret. Additionally experimental difficulties in verifying that supersonic combustion actually occurred, or that actual net thrust was produced mean that at least four consortia have legitimate claims to "firsts", with several nations and institutions involved in each consortium. On June 15, 2007, the US Defense Advanced Research Project Agency (DARPA) and the Australian Defence Science and Technology Organization (DSTO), announced a successful scramjet flight at Mach 10 using rocket engines to boost the test vehicle to hypersonic speeds, at the Woomera Rocket Range in Central Australia.

No scramjet powered vehicle has yet been produced outside an experimental program.

Design principles

Scramjet engines are a type of jet engine, and rely on the combustion of fuel and an oxidizer to produce thrust. Similar to conventional jet engines, scramjet-powered aircraft carry the fuel on board, and obtain the oxidizer by the ingestion of atmospheric oxygen (as compared to rockets, which carry both fuel and an oxidizing agent). This requirement limits scramjets to suborbital atmospheric flight, where the oxygen content of the air is sufficient to maintain combustion.

Basic principles

Scramjets are designed to operate in the hypersonic flight regime, beyond the reach of turbojet engines, and, along with ramjets, fill the gap between the high efficiency of turbojets and the high speed of rocket engines. Turbomachinery-based engines, while highly efficient at subsonic speeds, become increasingly inefficient at transonic speeds, as the compressor fans found in turbojet engines require subsonic speeds to operate. While the flow from transonic to low supersonic speeds can be decelerated to these conditions, doing so at supersonic speeds results in a tremendous increase in temperature and a loss in the total pressure of the flow. Around Mach 3–4, turbomachinery is no longer useful, and ram-style compression becomes the preferred method.[11]

Ramjets utilize high-speed characteristics of air to literally 'ram' air through an inlet nozzle into the combustor. At transonic and supersonic flight speeds, the air upstream of the nozzle is not able to move out of the way quickly enough, and is compressed within the nozzle before being diffused into the combustor. Combustion in a ramjet takes place at subsonic velocities, similar to turbojets, but the combustion products are then accelerated through a convergent-divergent nozzle to supersonic speeds. As they have no mechanical means of compression, ramjets cannot start from a standstill, and generally do not achieve sufficient compression until supersonic flight. The lack of intricate turbomachinery allows ramjets to deal with the temperature rise associated with decelerating a supersonic flow to subsonic speeds, but this only goes so far: at near-hypersonic velocities, the temperature rise and inefficiencies discourage decelerating the flow to the magnitude found in ramjet engines.[11]

Scramjet engines operate on the same principles as ramjets, but do not decelerate the flow to subsonic velocities. Rather, a scramjet combustor is supersonic: the inlet decelerates the flow to a lower Mach number for combustion, after which it is accelerated to an even higher Mach number through the nozzle. By limiting the amount of deceleration, temperatures within the engine are kept at a tolerable level, from both a material and combustive standpoint. Even so, current scramjet technology requires the use of high-energy fuels and active cooling schemes to maintain sustained operation, often using hydrogen and regenerative cooling techniques.[12]

Theory

All scramjet engines have an intake, which compresses the incoming air, fuel injectors, a combustion chamber, and a divergent thrust nozzle. Sometimes engines also include a region which acts as a flame holder, although the high stagnation temperatures mean that an area of focused waves may be used, rather than a discrete engine part as seen in turbine engines. Other engines use pyrophoric fuel additives, such as silane, to avoid such issues. An isolator between the inlet and combustion chamber is often included to improve the homogeneity of the flow in the combustor and to extend the operating range of the engine.

A scramjet is reminiscent of a ramjet. In a typical ramjet, the supersonic inflow of the engine is decelerated at the inlet to subsonic speeds and then reaccelerated through a nozzle to supersonic speeds to produce thrust. This deceleration, which is produced by a normal shock, creates a total pressure loss which limits the upper operating point of a ramjet engine.

For a scramjet, the kinetic energy of the freestream air entering the scramjet engine is large comparable to the energy released by the reaction of the oxygen content of the air with a fuel (say hydrogen). Thus the heat released from combustion at Mach 25 is around 10% of the total enthalpy of the working fluid. Depending on the fuel, the kinetic energy of the air and the potential combustion heat release will be equal at around Mach 8. Thus the design of a scramjet engine is as much about minimizing drag as maximizing thrust.

This high speed makes the control of the flow within the combustion chamber more difficult. Since the flow is supersonic, no upstream influence propagates within the freestream of the combustion chamber. Thus throttling of the entrance to the thrust nozzle is not a usable control technique. In effect, a block of gas entering the combustion chamber must mix with fuel and have sufficient time for initiation and reaction, all the while traveling supersonically through the combustion chamber, before the burned gas is expanded through the thrust nozzle. This places stringent requirements on the pressure and temperature of the flow, and requires that the fuel injection and mixing be extremely efficient. Usable dynamic pressures lie in the range 20 to 200 kPa (0.2-2 bar), where

q = \frac{1}{2}\rho v^2

where

q is the dynamic pressure of the gas
ρ (rho) is the density of the gas
v is the velocity of the gas

To keep the combustion rate of the fuel constant, the pressure and temperature in the engine must also be constant. This is problematic because the airflow control systems that would facilitate this are not physically possible in a scramjet launch vehicle due to the large speed and altitude range involved, meaning that it must travel at an altitude specific to its speed. Because air density reduces at higher altitudes, a scramjet must climb at a specific rate as it accelerates to maintain a constant air pressure at the intake. This optimal climb/descent profile is called a "constant dynamic pressure path". It is thought that scramjets might be operable up to an altitude of 75 km.[13]

Fuel injection and management is also potentially complex. One possibility would be that the fuel be pressurized to 100 bar by a turbo pump, heated by the fuselage, sent through the turbine and accelerated to higher speeds than the air by a nozzle. The air and fuel stream are crossed in a comb like structure, which generates a large interface. Turbulence due to the higher speed of the fuel leads to additional mixing. Complex fuels like kerosene need a long engine to complete combustion.

The minimum Mach number at which a scramjet can operate is limited by the fact that the compressed flow must be hot enough to burn the fuel, and have pressure high enough that the reaction be finished before the air moves out the back of the engine. Additionally, in order to be called a scramjet, the compressed flow must still be supersonic after combustion. Here two limits must be observed: Firstly, since when a supersonic flow is compressed it slows down, the level of compression must be low enough (or the initial speed high enough) not to slow the gas below Mach 1. If the gas within a scramjet goes below Mach 1 the engine will "choke", transitioning to subsonic flow in the combustion chamber. This effect is well known amongst experimenters on scramjets since the waves caused by choking are easily observable. Additionally, the sudden increase in pressure and temperature in the engine can lead to an acceleration of the combustion, leading to the combustion chamber exploding.

Secondly, the heating of the gas by combustion causes the speed of sound in the gas to increase (and the Mach number to decrease) even though the gas is still travelling at the same speed. Forcing the speed of air flow in the combustion chamber under Mach 1 in this way is called "thermal choking". It is clear that a pure scramjet can operate at Mach numbers of 6-8,[14] but in the lower limit, it depends on the definition of a scramjet. Certainly there are designs where a ramjet transforms into a scramjet over the Mach 3-6 range (Dual-mode scramjets).[15] In this range however, the engine is still receiving significant thrust from subsonic combustion of "ramjet" type.

The high cost of flight testing and the unavailability of ground facilities have hindered scramjet development. A large amount of the experimental work on scramjets has been undertaken in cryogenic facilities, direct-connect tests, or burners, each of which simulates one aspect of the engine operation. Further, vitiated facilities, storage heated facilities, arc facilities and the various types of shock tunnels each have limitations which have prevented perfect simulation of scramjet operation. The HyShot flight test showed the relevance of the 1:1 simulation of conditions in the T4 and HEG shock tunnels, despite having cold models and a short test time. The NASA-CIAM tests provided similar verification for CIAM's C-16 V/K facility and the Hyper-X project is expected to provide similar verification for the Langley AHSTF,[16] CHSTF[17] and 8 ft (2.4 m) HTT.

Computational fluid dynamics has only recently reached a position to make reasonable computations in solving scramjet operation problems. Boundary layer modeling, turbulent mixing, two-phase flow, flow separation, and real-gas aerothermodynamics continue to be problems on the cutting edge of CFD. Additionally, the modeling of kinetic-limited combustion with very fast-reacting species such as hydrogen makes severe demands on computing resources. Reaction schemes are numerically stiff requiring reduced reaction schemes.

Much of scramjet experimentation remains classified. Several groups including the US Navy with the SCRAM engine between 1968–1974, and the Hyper-X program with the X-43A have claimed successful demonstrations of scramjet technology. Since these results have not been published openly, they remain unverified and a final design method of scramjet engines still does not exist.

The final application of a scramjet engine is likely to be in conjunction with engines which can operate outside the scramjet's operating range. Dual-mode scramjets combine subsonic combustion with supersonic combustion for operation at lower speeds, and rocket-based combined cycle (RBCC) engines supplement a traditional rocket's propulsion with a scramjet, allowing for additional oxidizer to be added to the scramjet flow. RBCCs offer a possibility to extend a scramjet's operating range to higher speeds or lower intake dynamic pressures than would otherwise be possible.

Advantages and disadvantages of scramjets

Advantages

  1. Does not have to carry oxygen
  2. No rotating parts makes it easier to manufacture
  3. Has a higher specific impulse (change in momentum per unit of propellant) than a conventional engine; could provide between 1000 and 4000 seconds, while a rocket only provides 600 seconds or less
  4. Higher speed could mean cheaper access to outer space in the future

Special cooling and materials

Unlike a rocket that quickly passes mostly vertically through the atmosphere or a turbojet or ramjet that flies at much lower speeds, a hypersonic airbreathing vehicle optimally flies a "depressed trajectory", staying within the atmosphere at hypersonic speeds. Because scramjets have only mediocre thrust-to-weight ratios, acceleration would be limited. Therefore time in the atmosphere at hypersonic speed would be considerable, possibly 15–30 minutes. Similar to a reentering space vehicle, heat insulation would be a formidable task. The time in the atmosphere would be greater than that for a typical space capsule, but less than that of the space shuttle.

New materials offer good insulation at high temperature, but they often sacrifice themselves in the process. Therefore studies often plan on "active cooling", where coolant circulating throughout the vehicle skin prevents it from disintegrating. Often the coolant is the fuel itself, in much the same way that modern rockets use their own fuel and oxidizer as coolant for their engines. All cooling systems add weight and complexity to a launch system. The cooling of scramjets in this way may result in greater efficiency, as heat is added to the fuel prior to entry into the engine, but result in increased complexity and weight which ultimately could outweigh any performance gains.

Vehicle performance

The performance of a launch system is complex and depends greatly on its weight. Normally craft are designed to maximise range (R), orbital radius (R) or payload mass fraction (\Gamma) for a given engine and fuel. This results in tradeoffs between the efficiency of the engine (takeoff fuel weight) and the complexity of the engine (takeoff dry weight), which can be expressed by the following:

\Pi_e%2B\Pi_f%2B\frac{1}{\Gamma}=1

Where :

A scramjet increases the mass of the engine \Pi_e over a rocket, and decreases the mass of the fuel \Pi_f. It can be difficult to decide whether this will result in an increased \Gamma (which would be an increased payload delivered to a destination for a constant vehicle takeoff weight). The logic behind efforts driving a scramjet is (for example) that the reduction in fuel decreases the total mass by 30%, while the increased engine weight adds 10% to the vehicle total mass. Unfortunately the uncertainty in the calculation of any mass or efficiency changes in a vehicle is so great that slightly different assumptions for engine efficiency or mass can provide equally good arguments for or against scramjet powered vehicles.

Additionally, the drag of the new configuration must be considered. The drag of the total configuration can be considered as the sum of the vehicle drag (D) and the engine installation drag (D_e). The installation drag traditionally results from the pylons and the coupled flow due to the engine jet, and is a function of the throttle setting. Thus it is often written as:

D_e=\phi_eF Where:

For an engine strongly integrated into the aerodynamic body, it may be more convenient to think of (D_e) as the difference in drag from a known base configuration.

The overall engine efficiency can be represented as a value between 0 and 1 (\eta_0), in terms of the specific impulse of the engine:

\eta_0=\frac{g_0V_0}{h_{PR}}\cdot I_{sp}=\frac{\mbox{Thrust Power}}{\mbox{Chemical energy rate}}

Where:

Specific impulse is often used as the unit of efficiency for rockets, since in the case of the rocket, there is a direct relation between specific impulse, specific fuel consumption and exhaust velocity. This direct relation is not generally present for airbreathing engines, and so specific impulse is less used in the literature. Note that for an airbreathing engine, both \eta_0 and I_{sp} are a function of velocity.

The specific impulse of a rocket engine is independent of velocity, and common values are between 200 and 600 seconds (450s for the space shuttle main engines). The specific impulse of a scramjet varies with velocity, reducing at higher speeds, starting at about 1200s, although values in the literature vary.

For the simple case of a single stage vehicle, the fuel mass fraction can be expressed as:

\Pi_f=1-\exp\left[-\frac{\left(\frac{V_{initial}^2}{2}-\frac{V_i^2}{2}\right)%2B\int{g}\,dr}{\eta_0h_{PR}\left(1-\frac{D%2BD_e}{F}\right)}\right]

Where this can be expressed for single stage transfer to orbit as:

\Pi_f=1-\exp\left[-\frac{g_0r_0\left(1-\frac{1}{2}\frac{r_0}{r}\right)}{\eta_0h_{PR}\left(1-\frac{D%2BD_e}{F}\right)}\right]

or for level atmospheric flight from air launch (missile flight):

\Pi_f=1-\exp\left[-\frac{g_0R}{\eta_0h_{PR}\left(1-\phi_e\right)\frac{C_L}{C_D}}\right]

Where R is the range, and the calculation can be expressed in the form of the Breguet range formula:

\Pi_f=1-e^{-BR}
B=\frac{g_0}{\eta_0h_{PR}\left(1-\phi_e\right)\frac{C_L}{C_D}}

Where:

This extremely simple formulation, used for the purposes of discussion assumes:

However they are true generally for all engines.

Initial propulsion requirements

A scramjet cannot produce efficient thrust unless boosted to high speed, around Mach 5, although depending on the design it could act as a ramjet at low speeds. A horizontal take-off aircraft would need conventional turbofan or rocket engines to take off, sufficiently large to move a heavy craft. Also needed would be fuel for those engines, plus all engine-associated mounting structure and control systems. Turbofan engines are heavy and cannot easily exceed about Mach 2-3, so another propulsion method would be needed to reach scramjet operating speed. That could be ramjets or rockets. Those would also need their own separate fuel supply, structure, and systems. Many proposals instead call for a first stage of droppable solid rocket boosters, which greatly simplifies the design.

Testing difficulties

Unlike jet or rocket propulsion systems facilities which can be tested on the ground, testing scramjet designs use extremely expensive hypersonic test chambers or expensive launch vehicles, both of which lead to high instrumentation costs. Tests using launched test vehicles very typically end with destruction of the test item and instrumentation.

Advantages and disadvantages for orbital vehicles

Propellant

An advantage of a hypersonic airbreathing (typically scramjet) vehicle like the X-30 is avoiding or at least reducing the need for carrying oxidizer. For example the space shuttle external tank holds 616,432 kg of liquid oxygen (LOX) and 103,000 kg of liquid hydrogen (LH2) while having an empty weight of 30,000 kg. The orbiter gross weight is 109,000 kg with a maximum payload of about 25,000 kg and to get the assembly off the launch pad the shuttle uses two very powerful solid rocket boosters with a weight of 590,000 kg each. If the oxygen could be eliminated, the vehicle could be lighter at liftoff and maybe carry more payload. That would be an advantage, but the central motivation in pursuing hypersonic airbreathing vehicles would be to reduce cost.

On the other hand, scramjets spend more time in the atmosphere and require more hydrogen fuel to deal with aerodynamic drag. Whereas liquid oxygen is quite a dense fluid, liquid hydrogen has much lower density and takes up much more volume. This means that the vehicle using this fuel becomes much bigger and gives even more drag.[18]

Thrust-to-weight ratio

One issue is that scramjet engines are predicted to have exceptionally poor thrust-to-weight ratio, when installed in a launch vehicle, of around 2.[19] A rocket has the advantage that its engines have very high thrust-weight ratios (~100:1), while the tank to hold the liquid oxygen approaches a tankage ratio of ~100:1 also. Thus a rocket can achieve a very high mass fraction, which improves performance. By way of contrast the projected thrust/weight ratio of scramjet engines of about 2 mean a very much larger percentage of the takeoff mass is engine (ignoring that this fraction increases anyway by a factor of about four due to the lack of onboard oxidiser). In addition the vehicle's lower thrust does not necessarily avoid the need for the expensive, bulky, and failure prone high performance turbopumps found in conventional liquid-fuelled rocket engines, since most scramjet designs seem to be incapable of orbital speeds in airbreathing mode, and hence extra rocket engines are needed.

Need for additional propulsion to reach orbit

Scramjets might be able to accelerate from approximately Mach 5-7 to around somewhere between half of orbital velocity and orbital velocity (X-30 research suggested that Mach 17 might be the limit compared to an orbital speed of Mach 25, and other studies put the upper speed limit for a pure scramjet engine between Mach 10 and 25, depending on the assumptions made). Generally, another propulsion system (very typically rocket is proposed) is expected to be needed for the final acceleration into orbit. Since the delta-V is moderate and the payload fraction of scramjets high, lower performance rockets such as solids, hypergolics, or simple liquid fueled boosters might be acceptable.

Reentry

The scramjet's heat-resistant underside potentially doubles as its reentry system if a single-stage-to-orbit vehicle using non-ablative, non-active cooling is visualised. If an ablative shielding is used on the engine it will probably not be usable after ascent to orbit. If active cooling is used the loss of all fuel during the burn to orbit will also mean the loss of all cooling for the thermal protection system.

Costs

Reducing the amount of fuel and oxidizer does not necessarily improve costs as rocket propellants are comparatively very cheap. Indeed, the unit cost of the vehicle can be expected to end up far higher, since aerospace hardware cost is about two orders of magnitude higher than liquid oxygen, fuel and tankage, and scramjet hardware seems to be much heavier than rockets for any given payload. Still, if scramjets enable reusable vehicles, this could theoretically be a cost benefit. Whether equipment subject to the extreme conditions of a scramjet can be reused sufficiently many times is unclear; all flown scramjet tests only survive for short periods and have never been designed to survive a flight to date.

The eventual cost of such a vehicle is the subject of intense debate since even the best estimates disagree whether a scramjet vehicle would be advantageous. It is likely that a scramjet vehicle would need to lift more load than a rocket of equal takeoff weight in order to be equally as cost efficient (if the scramjet is a non-reusable vehicle).

Issues

Space launch vehicles may or may not benefit from having a scramjet stage. A scramjet stage of a launch vehicle theoretically provides a specific impulse of 1000 to 4000 s whereas a rocket provides less than 450 s while in the atmosphere,[20][21] potentially permitting much cheaper access to space. A scramjet's specific impulse decreases rapidly with speed, however, and the vehicle would suffer from a relatively low lift to drag ratio.

The installed thrust to weight ratio of scramjets compares very unfavorably with the 50-100 of a typical rocket engine. This is compensated for in scramjets partly because the weight of the vehicle would be carried by aerodynamic lift rather than pure rocket power (giving reduced 'gravity losses'), but scramjets would take much longer to get to orbit due to lower thrust which greatly offsets the advantage. The takeoff weight of a scramjet vehicle is significantly reduced over that of a rocket, due to the lack of onboard oxidiser, but increased by the structural requirements of the larger and heavier engines.

Whether this vehicle would be reusable or not is still a subject of debate and research.

Applications

An aircraft using this type of jet engine could dramatically reduce the time it takes to travel from one place to another, potentially putting any place on Earth within a 90 minute flight. However, there are questions about whether such a vehicle could carry enough fuel to make useful length trips, and there are issues with sonic booms.

Scramjet vehicle has been proposed for a single stage to tether vehicle, where a Mach 12 spinning orbital tether would pick up a payload from a vehicle at around 100 km and carry it to orbit.[22]

Progress in the 2000s

Main article: Scramjet programs

In the 2000s, significant progress was made in the development of hypersonic technology, particularly in the field of scramjet engines.

US efforts are probably the best funded, and the Hyper-X team claimed the first flight of a thrust-producing scramjet powered vehicle with full aerodynamic maneuvering surfaces in 2004 with the X-43A.[23][24] However, the first group to demonstrate a scramjet working in an atmospheric test was a project by a joint British and Australian team from UK defense company QinetiQ and the University of Queensland.

The HyShot project demonstrated scramjet combustion on July 30, 2002. The scramjet engine worked effectively and demonstrated supersonic combustion in action. However, the engine was not designed to provide thrust to propel a craft. It was designed more or less as a technology demonstrator.

On Friday, June 15, 2007, the US Defense Advanced Research Project Agency (DARPA), in cooperation with the Australian Defence Science and Technology Organization (DSTO), announced a successful scramjet flight at Mach 10 using rocket engines to boost the test vehicle to hypersonic speeds.[25]

A series of scramjet ground test were completed at NASA Langley Arc-Heated Scramjet Test Facility (AHSTF) at simulated Mach 8 flight conditions. These experiments were used to support HiFIRE flight 2.[26]

On May 22, 2009, Woomera hosted the first successful test flight of a hypersonic aircraft in HIFire. The launch was one of 10 planned test flights. The series of up to 10 planned hypersonic flight experiments are part of a joint research program between the Defence Science and Technology Organisation and the US Air Force, designated as the Hypersonic International Flight Research Experimentation (HIFiRE).[27] HIFiRE is investigating hypersonics technology (the study of flight exceeding five times the speed of sound) and its application to advanced scramjet-powered space launch vehicles — the objective is to support the new Boeing X-51 scramjet demonstrator while also building a strong base of flight test data for quick-reaction space launch development and hypersonic "quick-strike" weapons.[27]

On 22 and 23 March 2010, Australian and American defence scientists successfully tested a (HIFiRE) hypersonic rocket. It reached an atmospheric velocity of "more than 5,000 kilometres per hour" after taking off from the Woomera Test Range in outback South Australia.[28][29]

On May 27, 2010, NASA and the United States Air Force successfully flew the X-51A Waverider for approximately 200 seconds at Mach 5, setting a new world record hypersonic airspeed. The Waverider flew autonomously before losing acceleration for an unknown reason and destroying itself as planned. The test was declared a success. The X-51A was carried aboard a B-52, accelerated to Mach 4.5 via a solid rocket booster, and then ignited the Pratt & Whitney Rocketdyne scramjet engine to reach Mach 5 at 70,000 feet.[30] However, a second flight June 13, 2011 was ended prematurely when the engine lit briefly on ethylene but failed to transition to its primary JP7 fuel, failing to reach full power.[31][32]

On 16 November 2010, Australian scientists successfully demonstrated that the high-speed flow in a naturally non-burning scramjet engine can be ignited using a pulsed laser source.[33]

The US Army successfully tested the scramjet powered "Advanced Hypersonic Weapon" (AHW) on November 18, 2011. The weapon reached speeds over Mach 5 and hit a target around 2500 miles distant.

See also

Notes

  1. ^ "SR-71 Online - A-12 Blackbird". SR-71 online. http://www.sr-71.org/blackbird/a-12/. Retrieved 10 December 2010. 
  2. ^ "Lockheed SR-71A Blackbird". March Airfield Museum. http://www.marchfield.org/sr71a.htm. Retrieved 1 July 2010. 
  3. ^ Segal 2009, pp. 1.
  4. ^ Calaguori, Nancy; Kidder, Bryan (2 May 2010). "Pratt & Whitney Rocketdyne Scramjet Powers Historic First Flight of X-51A WaveRider". Press Releases. Pratt & Whitney Rocketdyne. http://www.pw.utc.com/Media+Center/Press+Releases/Pratt+%26+Whitney+Rocketdyne+Scramjet+Powers+Historic+First+Flight+of+X-51A+WaveRider. Retrieved 1 July 2010. 
  5. ^ Segal 2009, pp. 3–11.
  6. ^ "Frederick S. Billig, Ph.D. (1933-2006)". Innovation Hall of Fame. University of Maryland. http://www.eng.umd.edu/ihof/inductees/billig.html. Retrieved 30 April 2010. 
  7. ^ "Milestones in the history of scramjets — UQ News Online — The University of Queensland". University of Queensland, UQ News. http://www.uq.edu.au/news/?article=3399. Retrieved 18 August 2009. 
  8. ^ Roudakov, A.S., Y. Schickhman, V. Semenov, Ph. Novelli, and O. Fourt, “Flight Testing an Axisymmetric Scramjet: Russian Recent Advances,” 44th Congress of the International Astronautical Federation, Oct. 16–22, 1993, Graz, Austria
  9. ^ A.Roudakov, V.Semenov, V.Kopchenov, J.Hicks "Future Flight Test Plans of an Axisymmetric Hydrogen-Fueled Scramjet Engine on the Hypersonic Flying Laboratory" AIAA 96-4572. 7th International Spaceplanes and Hypersonics Systems & Technology Conference November 18–22, 1996/Norfolk, Virginia
  10. ^ A.Roudakov, V.Semenov, J.Hicks "Recent Flight Test Results of the Joint CIAMNASA Mach 6.5 Scramjet Flight Program" NASA/TP-1998-206548
  11. ^ a b Hill & Peterson 1992, pp. 21.
  12. ^ Segal 2009, pp. 4.
  13. ^ "Scramjets". Orbitalvector.com. 2002-07-30. http://www.orbitalvector.com/Orbital%20Travel/Scramjets/Scramjets.htm. Retrieved 2009-08-18. 
  14. ^ Paull, A.; Stalker, R.J., Mee, D.J. (1995). "Experiments on supersonic combustion ramjet propulsion in a shock tunnel". Jfm 296: 156-183. 
  15. ^ Voland, R.T., Auslender, A.H., Smart, M.K., Roudakov, A.S., Semenov, V.L., Kopchenov, V. "CIAM/NASA Mach 6.5 scramjet flight and ground test", AIAA-99-4848.
  16. ^ "The Langley Arc-Heated Scramjet Test Facility Brochure". Wte.larc.nasa.gov. 2005-11-17. http://wte.larc.nasa.gov/facilities/hypersonic/arc-heated.cfm?field=11&id=2&fac=1. Retrieved 2009-08-18. 
  17. ^ "The Langley Combustion-Heated Scramjet Test Facility Brochure". Wte.larc.nasa.gov. 2005-11-17. http://wte.larc.nasa.gov/facilities/hypersonic/combustion.cfm?field=12&id=2&fac=1. Retrieved 2009-08-18. 
  18. ^ States, United; Assessment, Office of Technology; Congress, (2003-05-14). pg 78. Books.google.com. ISBN 9781428922334. http://books.google.com/?id=Smtn0fbL-EAC&lpg=PA77&dq=scramjet&pg=PA78. Retrieved 2009-08-18. 
  19. ^ Varvill, R., Bond, A. "A Comparison of Propulsion Concepts for SSTO Reuseable Launchers", JBIS, Vol 56, pp 108-117, 2003. Figure 7.
  20. ^ Kors, D.L. “Design considerations for combined air breathing-rocket propulsion systems.”, AIAA Paper No. 90-5216, 1990.
  21. ^ Varvill, R., Bond, A. "A Comparison of Propulsion Concepts for SSTO Reuseable Launchers", JBIS, Vol 56, pp 108-117, 2003. Figure 8.
  22. ^ Hypersonic Airplane Space Tether Orbital Launch (HASTOL) System
  23. ^ Dr. Phillip T. Harsha, Lowell C. Keel, Dr. Anthony Castrogiovanni, Robert T. Sherrill, "X-43A Vehicle Design and Manufacture" (pdf), AIAA 2005-3334, http://pdf.aiaa.org/preview/CDReadyMISPHST05_1136/PV2005_3334.pdf 
  24. ^ {{cite |url=http://pdf.aiaa.org/preview/CDReadyMASM06_778/PV2006_1.pdf |last=C. McClinton |title=X-43–Scramjet Power Breaks the Hypersonic Barrier |format=pdf
  25. ^ "Scramjet hits Mach 10 over Australia", New Scientist, 15 June 2007, accessed 17 November 2010.
  26. ^ Cabell, Karen; Hass, Neal; Storch, Andrea; Gruber, Mark. "HIFiRE Direct-Connect Rig (HDCR) Phase I Scramjet Test Results from the NASA Langley Arc-Heated Scramjet Test Facility". NASA Langley Research Center. NASA Technical Reports Server. http://hdl.handle.net/2060/20110011173. Retrieved 21 September 2011. 
  27. ^ a b "Woomera hosts first HIFiRE hypersonic test flight". Daily Telegraph. 2009-05-24. http://www.dailytelegraph.com.au/news/indepth/woomera-hosts-first-hifire-hypersonic-test-flight/story-e6frewsr-1225715365056. 
  28. ^ "Scientists conduct second HIFiRE test". Sydney Morning Herald Online. 2010-03-22. http://news.smh.com.au/breaking-news-national/scientists-conduct-second-hifire-test-20100322-qqrp.html. 
  29. ^ "'Success for hypersonic outback flight". ABC Online. 2010-03-23. http://www.abc.net.au/news/stories/2010/03/23/2853372.htm. 
  30. ^ "X-51A races to hypersonic record". C-Net News. 27 May 2010. http://news.cnet.com/8301-13639_3-20006101-42.html. 
  31. ^ "Hypersonic X-51A Scramjet Failure Perplexes Air Force" http://www.foxnews.com/scitech/2011/07/29/hypersonic-x-51a-scramjet-failure-perplexes-air-force/
  32. ^ "X-51A Waverider Test Falls Short"http://www.youtube.com/watch?v=-mMLZPoU8JU
  33. ^ "Researchers put spark into scramjets". Australian Broadcasting Corporation, ABC News. 16 November 2010. http://www.abc.net.au/science/articles/2010/11/16/3067887.htm?site=science. 

References

External links