Renix made automobile electronic ignitions, fuel injection systems, electronic automatic transmission controls, and various engine sensors.
The term Renix also has a number of applications. In certain carburetor equipped Renault and Volvo models, it provides an electronic ignition system, consisting of an engine control unit (ECU) to replace the job of contact breaker points in the distributor. The system uses an angle sensor and a number of fuel sensors to provide a maintenance-free ignition system. The ECU is sealed and cannot be serviced, and the EPROM cannot be re-programmed.
Later, the name was synonymous with a form of fuel injection. In such an application, it consisted of an ECU and a number of sensors. It was first seen in engines produced by Renault (Renault 21, 25, and Espace) in 2.0 L (122 cu in) and 2.2 L (134 cu in) capacities. It is better known in America for its application in the AMC 4.0 L displacing 3,960 cc (242 cu in) straight-6 engines. Production began by American Motors (AMC) with the 1987 Jeep Cherokee (XJ) models. It was preceded by the AMC Computerized Engine Control, and followed by the Mopar MPI system.
Contents |
Renix Electronique S.A., was established in 1981 as a joint venture by Renault with 51% interest and Bendix with 49% that was headquartered in Toulouse.[1] When Renault encountered financial troubles in 1985, it sold its interest in Renix to AlliedSignal Corp., a major auto industry supplier and the new owner of Bendix.[2]
Renix Corporation of America was the North American subsidiary of Renix Electronique and was formed to provided Sales, Logistics, Engineering and Quality support to American Motors. Renix Corporation of America was also absorbed by AlliedSignal Corporation when it purchased Renix Electronique from Renault.
The Renix system was used in the J series engines as fitted to the Renault 21 and Savanna/Nevada, the Renault 25, and the Renault Espace. It was a multi-point fuel injection system, as opposed to a single-point system, with a number of air, throttle and pinking sensors, and an advanced computer. Application of the system could first be seen in 1984, three years before its American debut. The Renix system pushed the power of the carburetor-fed 1,995 cc (122 cu in) engine from 104–120 bhp (78–89 kW). It could also be found in 2.2 L engines fitted to R21, 25, and Espace models.
The Renix electronic ignition system consists of a solid-state Ignition Control Module (ICM), a distributor, a crankshaft position sensor, and an Electronic Control Unit (ECU). The Renix ECU has a powerful microprocessor that was advanced technology for its time.[3] It also incorporates an engine knocking sensor that allows the computer to know if detonation is occurring, thus allowing the computer to make adaptive control by individual cylinder corrections to prevent pinging. The knock detection uses the signal from a wide bank accelerometer mounted on the cylinder head. Good signal to noise ratio is obtained primarily through angular discrimination.
The Renix system has more inputs than the later Mopar system and in some ways is more complex.[4] Its knock sensor automatically tunes the spark advance curve to an optimum mix for each cylinder. Some Renix controlled engines will actually get better fuel economy using higher octane fuel.[4]
The Renix computer was first used on 1986 AMC 2.5 L four-cylinder enginess. The system improved the drivability of the Jeep Cherokee XJ models and the Comanche pickups over the first two months of production that were fitted with carburetors. The power increase was also noticeable. The Renix system was used through the 1990 model year. Unfortunately, the Renix system is now handicapped because there are few scan tools that can be "plugged in" to this on-board diagnostics computer.[3] Model years:
The Renix control system was only found on the 1987-1990 Jeep Cherokee and Comanche with AMC-designed engines (the control setup used with the 2.8 L (171 cu in) V6 was OBD-I General Motors, and the early Diesel was a 2.1 L (128 cu in) Renault turbodiesel I4 that used its own specific control setup.)
The CJ/YJ "Universal" Jeep Wrangler did not get the AMC 4.0 engine until 1991, when it was accompanied by Chrysler-designed electronics as well. Until then, it retained the AMC 258 cu in (4.2 L) engine with a carburetor. No other Jeep vehicle was equipped with Renix electronic controls.
In a typical Jeep application, the ignition control module (ICM) is located in engine compartment. It consists of a solid-state ignition circuit, as well as an integrated ignition coil that can be removed and serviced separately. Electronic signals from the ECU to the ICM determine the amount of ignition timing or retard needed to meet engine power requirements. The ECU provides an input signal to the ICM. The ICM has outputs for a tach signal to the tachometer and a high voltage signal from the coil to the distributor. The crankshaft position sensor senses TDC (Top Dead Center) and BDC crankshaft positions, as well as engine RPM. This sensor is secured by special shouldered bolts to flywheel/drive plate housing and is not adjustable.
The Renix control system is "pre-OBD," and therefore does not have a "Check Engine Lamp". It also does not "store" or "throw" Diagnostic Trouble Codes (DTCs) or "Parameter IDs" (PIDs) - see: OBD-II PIDs.[5] This is a common problem at vehicle inspection, particularly in California and other jurisdictions with emission standards. Most inspection stations are not aware and will try to explain that the CEL/MIL "doesn't work" (note: there may be a cutout for it, but no bulb). It is recommended that the inspection technician be shown the "OBD Exempt" federal emissions label (located under the hood) and/or have the factory service manual as a reference to avoid this problem.
The Volvo 700 Series and some of the Volvo 300 Series used a B200K 2.0 L inline-4 naturally aspirated engine with Renix ignition and some 300 series Volvos with Renault powerplants. The 300 Volvo series is not known U.S. It was manufactured in Holland and some units in Australia for the local Right Hand Drive (RHD) market.
All 300 series Volvo cars with gasoline engines came with Renix/Bendix ignition 1983 onwards until 1991 when production of the 300 series stopped.[6]
Engines equipped with Renix ignition:
Renault (F [=OHC] and C [=OHV Pushrod] series) units:
Ripper, Stephen Michael - Employee of Renix Corporation of America