In computing, performance per watt is a measure of the energy efficiency of a particular computer architecture or computer hardware. Literally, it measures the rate of computation that can be delivered by a computer for every watt of power consumed.
The performance and power consumption metrics used depend on the definition; reasonable measures of performance are FLOPS, MIPS, or the score for any performance benchmark. Several measures of power usage may be employed, depending on the purposes of the metric; for example, a metric might only consider the electrical power delivered to a machine directly, while another might include all power necessary to run a computer, such as cooling and monitoring systems. Often the power is the average power used while running the benchmark, but sometimes other measures of power usage may be employed (e.g. peak power, idle power.)
For example, the early UNIVAC I computer performed approximately 0.015 operations per watt-second (performing 1,905 operations per second, while consuming 125 kW).
Most of the power a computer uses is converted into heat, so a system that takes fewer watts to do a job will require less cooling to maintain a given operating temperature. Reduced cooling demands makes it easier to quiet a computer. Lower energy consumption can also make it less costly to run, and reduce the environmental impact of powering the computer (see green computing). If installed where there is limited climate control, a lower power computer will operate at a lower temperature, which may make it more reliable. In a climate controlled environment, reductions in direct power use may also create savings in climate control energy.
Computing energy consumption is sometimes also measured by reporting the energy required to run a particular benchmark, for instance EEMBC EnergyBench. Energy consumption figures for a standard workload may make it easier to judge the effect of an improvement in energy efficiency, just as the use of L/100km is easier than reciprocal measures (such as miles per gallon) when judging impact of automotive fuel economy.
Performance (in operations/second) per watt can also be written as operations/watt-second, or operations/joule, since 1 watt = 1 joule/second.
Contents |
FLOPS (Floating Point Operations Per Second) per watt is a common measure. Like the FLOPS it is based on, the metric is usually applied to scientific computing and simulations involving many floating point calculations.
As of June 2011[update], the Green500 list rates IBM NNSA/SC Blue Gene/Q Prototype 2 as the most efficient supercomputer on the TOP500 in terms of FLOPS per Watt, running at 2097.19 MFLOPS/Watt.[1]
On 9 June 2008, CNN reported that IBM's Roadrunner supercomputer achieves 376 MFLOPS/Watt.[2] [3]In November 2010, IBM machine, Blue Gene/Q achieves 1684 MFLOPS/Watt. [4][5]
As part of Intel's Tera-Scale research project, the team produced an 80 core CPU that can achieve over 16 GFLOPS/Watt.[6][7] The future of that CPU is not certain.
Microwulf, a low cost desktop Beowulf cluster of 4 dual core Athlon 64 x2 3800+ computers, runs at 58 MFLOPS/Watt.[8]
The Green500 list ranks computers from the TOP500 list of supercomputers in terms of energy efficiency. Typically measured as LINPACK FLOPS per watt.[9] [10]
Graphics processing units (GPU) have continued to increase in energy usage, while CPUs designers have recently focused on improving performance per watt. High performance GPUs may now be the largest power consumer in a system. Measures like 3DMark2006 score per watt can help identify more efficient GPUs.[11] However that may not adequately incorporate efficiency in typical use, where much time is spent doing less demanding tasks.[12]
With modern GPUs, energy usage is an important constraint on the possible power. GPU designs are usually highly scalable, allowing the manufacturer to put multiple chips on the same video card, or to use multiple video cards that work in parallel. Peak performance of any system is essentially limited by the amount of power it can draw and the amount of heat it can dissipate. Consequently, performance per watt of a GPU design translates directly into peak performance of a system that uses that design.
Since GPUs may also be used for some general purpose computation, sometimes their performance is measured in terms also applied to CPUs, such as FLOPS per watt.
While performance per watt is useful, absolute power requirements are also important. Claims of improved performance per watt may be used to mask increasing power demands. For instance, though newer generation GPU architectures may provide better performance per watt, continued performance increases can negate the gains in efficiency, and the GPUs continue to consume large amounts of power.[13].
Benchmarks that measure power under heavy load may not adequately reflect typical efficiency. For instance, 3DMark stresses the 3D performance of a GPU, but many computers spend most of their time doing less intense display tasks (idle, 2D tasks, displaying video). So the 2D or idle efficiency of the graphics system may be at least as significant for overall energy efficiency. Likewise, systems that spend much of their time in standby or soft off are not adequately characterized by just efficiency under load. To help address this some benchmarks, like SPECpower, include measurements at a series of load levels.[14]
The efficiency of some electrical components, such as voltage regulators, decreases with increasing temperature, so the power used may increase with temperature. Power supplies, motherboards, and some video cards are some of the subsystems affected by this. So their power draw may depend on temperature, and the temperature or temperature dependence should be noted when measuring.[15][16]
Performance per watt also typically does not include full life-cycle costs. Since computer manufacturing is energy intensive, and computers often have a relatively short lifespan, energy and materials involved in production, distribution, disposal and recycling often make up significant portions of their cost, energy use, and environmental impact.[17][18]
Energy required for climate control of the computer's surroundings is often not counted in the wattage calculation, but can be significant.[19]
SWaP (space, wattage and performance) is a Sun Microsystems metric for data centers, incorporating energy and space.
SWaP = Performance/(Space x Power)
Where performance is measured by any appropriate benchmark, and space is size of the computer. [20]
Energy efficiency benchmarks:
Other: