| Year created | 2004 |
|---|---|
| Created by | Intel · Dell · IBM · HP |
| Supersedes | AGP · PCI · PCI-X |
| Width in bits | 1–32 |
| Number of devices |
One device each on each endpoint of each connection. PCI Express switches can create multiple endpoints out of one endpoint to allow sharing one endpoint with multiple devices. |
| Capacity |
Per lane (each direction):
16 lane slot (each direction):
|
| Style | Serial |
| Hotplugging interface | Yes, if ExpressCard, PCI Express ExpressModule or XQD card |
| External interface | Yes, with PCI Express External Cabling such as Intel Thunderbolt |
PCI Express (Peripheral Component Interconnect Express), officially abbreviated as PCIe, is a computer expansion card standard designed to replace the older PCI, PCI-X, and AGP bus standards. PCIe has numerous improvements over the aforementioned bus standards, including higher maximum system bus throughput, lower I/O pin count and smaller physical footprint, better performance-scaling for bus devices, a more detailed error detection and reporting mechanism, and native hot-plug functionality. More recent revisions of the PCIe standard support hardware I/O virtualization.
The PCIe electrical interface is also used in a variety of other standards, most notably ExpressCard, a laptop expansion card interface.
Format specifications are maintained and developed by the PCI-SIG (PCI Special Interest Group), a group of more than 900 companies that also maintain the Conventional PCI specifications. PCIe 3.0 is the latest standard for expansion cards that is available on mainstream personal computers.[1][2]
Contents |
PCI Express is used in consumer, server, and industrial applications, as a motherboard-level interconnect (to link motherboard-mounted peripherals), a passive backplane interconnect and as an expansion card interface for add-in boards.
In virtually all modern PCs, from consumer laptops and desktops to enterprise data servers, the PCIe bus serves as the primary motherboard-level interconnect, connecting the host system processor with both integrated-peripherals (surface mounted ICs) and add-on peripherals (expansion cards.) In most of these systems, the PCIe bus co-exists with one or more legacy PCI buses, for backward compatibility with the large body of legacy PCI peripherals.
Conceptually, the PCIe bus is like a high-speed serial replacement of the older PCI/PCI-X bus,[3] an interconnect bus using shared address/data lines.
A key difference between PCIe bus and the older PCI is the bus topology. PCI uses a shared parallel bus architecture, where the PCI host and all devices share a common set of address/data/control lines. In contrast, PCIe is based on point-to-point topology, with separate serial links connecting every device to the root complex (host). Due to its shared bus topology, access to the older PCI bus is arbitrated (in the case of multiple masters), and limited to one master at a time, in a single direction. Furthermore, the older PCI's clocking scheme limits the bus clock to the slowest peripheral on the bus (regardless of the devices involved in the bus transaction). In contrast, a PCIe bus link supports full-duplex communication between any two endpoints, with no inherent limitation on concurrent access across multiple endpoints.
In terms of bus protocol, PCIe communication is encapsulated in packets. The work of packetizing and de-packetizing data and status-message traffic is handled by the transaction layer of the PCIe port (described later). Radical differences in electrical signaling and bus protocol require the use of a different mechanical form factor and expansion connectors (and thus, new motherboards and new adapter boards); PCI slots and PCIe slots are not interchangeable. At the software level, PCIe preserves backward compatibility with PCI; legacy PCI system software can detect and configure newer PCIe devices without explicit support for the PCIe standard, though PCIe's new features are inaccessible.
The PCIe link between two devices can consist of anywhere from 1 to 32 lanes. In a multi-lane link, the packet data is striped across lanes, and peak data-throughput scales with the overall link width. The lane count is automatically negotiated during device initialization, and can be restricted by either endpoint. For example, a single-lane PCIe (×1) card can be inserted into a multi-lane slot (×4, ×8, etc.), and the initialization cycle auto-negotiates the highest mutually supported lane count. The link can dynamically down-configure the link to use fewer lanes, thus providing some measure of failure tolerance in the presence of bad or unreliable lanes. The PCIe standard defines slots and connectors for multiple widths: ×1, ×4, ×8, ×16, ×32. This allows PCIe bus to serve both cost-sensitive applications where high throughput is not needed, as well as performance-critical applications such as 3D graphics, network (10 Gigabit Ethernet, multiport Gigabit Ethernet), and enterprise storage (SAS, Fibre Channel.)
As a point of reference, a PCI-X (133 MHz 64-bit) device and PCIe device at 4-lanes (×4), Gen1 speed have roughly the same peak transfer rate in a single-direction: 1064 MB/sec. The PCIe bus has the potential to perform better than the PCI-X bus in cases where multiple devices are transferring data communicating simultaneously, or if communication with the PCIe peripheral is bidirectional.
PCIe devices communicate via a logical connection called an interconnect[4] or link. A link is a point-to-point communication channel between 2 PCIe ports, allowing both to send/receive ordinary PCI-requests (configuration read/write, I/O read/write, memory read/write) and interrupts (INTx, MSI, MSI-X). At the physical level, a link is composed of 1 or more lanes.[4] Low-speed peripherals (such as an 802.11 Wi-Fi card) use a single-lane (×1) link, while a graphics adapter typically uses a much wider (and thus, faster) 16-lane link.
A lane is composed of a transmit and receive pair of differential lines. Each lane is composed of 4 wires or signal paths, meaning conceptually, each lane is a full-duplex byte stream, transporting data packets in 8 bit 'byte' format, between endpoints of a link, in both directions simultaneously.[5] Physical PCIe slots may contain from one to thirty-two lanes, in powers of two (1, 2, 4, 8, 16 and 32).[4] Lane counts are written with an × prefix (e.g., ×16 represents a sixteen-lane card or slot), with ×16 being the largest size in common use.[6]
The bonded serial format was chosen over a traditional parallel bus format due to the latter's inherent limitations, including single-duplex operation, excess signal count and an inherently lower bandwidth due to timing skew. Timing skew results from separate electrical signals within a parallel interface traveling down different-length conductors, on potentially different printed circuit board layers, at possibly different signal velocities. Despite being transmitted simultaneously as a single word, signals on a parallel interface experience different travel times and arrive at their destinations at different moments. When the interface clock rate is increased to a point where its inverse (i.e., its clock period) is shorter than the largest possible time between signal arrivals, the signals no longer arrive with sufficient coincidence to make recovery of the transmitted word possible. Since timing skew over a parallel bus can amount to a few nanoseconds, the resulting bandwidth limitation is in the range of hundreds of megahertz.
A serial interface does not exhibit timing skew because there is only one differential signal in each direction within each lane, and there is no external clock signal since clocking information is embedded within the serial signal. As such, typical bandwidth limitations on serial signals are in the multi-gigahertz range. PCIe is just one example of a general trend away from parallel buses to serial interconnects. Other examples include Serial ATA, USB, SAS, FireWire (1394) and RapidIO.
Multichannel serial design increases flexibility by allocating slow devices to fewer lanes than fast devices.
A PCIe card fits into a slot of its physical size or larger (maximum ×16), but may not fit into a smaller PCIe slot (×16 in a ×8 slot). Some slots use open-ended sockets to permit physically longer cards and negotiates the best available electrical connection. The number of lanes actually connected to a slot may also be less than the number supported by the physical slot size.
An example is a ×8 slot that actually only runs at ×1. These slots allow any ×1, ×2, ×4 or ×8 card, though only running at ×1 speed. This type of socket is called a ×8 (×1 mode) slot, meaning it physically accepts up to ×8 cards but only runs at ×1 speed. The advantage is that it can accommodate a larger range of PCIe cards without requiring motherboard hardware to support the full transfer rate. This keeps design and implementation costs down.
The following table identifies the conductors on each side of the edge connector on a ×4 PCI Express card. The solder side of the printed circuit board (PCB) is the A side, and the component side is the B side.[7]
| Pin | Side B | Side A | Comments |
|---|---|---|---|
| 1 | +12V | PRSNT1# | Pulled low to indicate card inserted |
| 2 | +12V | +12V | |
| 3 | +12V | +12V | |
| 4 | Ground | Ground | |
| 5 | SMCLK | TCK | SMBus and JTAG port pins |
| 6 | SMDAT | TDI | |
| 7 | Ground | TDO | |
| 8 | +3.3V | TMS | |
| 9 | TRST# | +3.3V | |
| 10 | +3.3Vaux | +3.3V | Standby power |
| 11 | WAKE# | PWRGD | Link reactivation, power good. |
| Key notch | |||
| 12 | Reserved | Ground | |
| 13 | Ground | REFCLK+ | Reference clock differential pair |
| 14 | HSOp(0) | REFCLK- | Lane 0 transmit data, + and − |
| 15 | HSOn(0) | Ground | |
| 16 | Ground | HSIp(0) | Lane 0 receive data, + and − |
| 17 | PRSNT2# | HSIn(0) | |
| 18 | Ground | Ground | |
| 19 | HSOp(1) | Reserved | Lane 1 transmit data, + and − |
| 20 | HSOn(1) | Ground | |
| 21 | Ground | HSIp(1) | Lane 1 receive data, + and − |
| 22 | Ground | HSIn(1) | |
| 23 | HSOp(2) | Ground | Lane 2 transmit data, + and − |
| 24 | HSOn(2) | Ground | |
| 25 | Ground | HSIp(2) | Lane 2 receive data, + and − |
| 26 | Ground | HSIn(2) | |
| 27 | HSOp(3) | Ground | Lane 3 transmit data, + and − |
| 28 | HSOn(3) | Ground | |
| 29 | Ground | HSIp(3) | Lane 3 receive data, + and − |
| 30 | Reserved | HSIn(3) | |
| 31 | PRSNT2# | Ground | |
| 32 | Ground | Reserved | |
An ×1 slot is a shorter version of this, ending after pin 18. ×8 and ×16 slots extend the pattern.
| Ground pin | Zero volt reference |
|---|---|
| Power pin | Supplies power to the PCIe card |
| Output pin | Signal from the card to the motherboard |
| Input pin | Signal from the motherboard to the card |
| Open drain | May be pulled low and/or sensed by multiple cards |
| Sense pin | Tied together on card |
| Reserved | Not presently used, do not connect |
PCI Express cards are allowed a maximum power consumption of 25W (×1: 10W for power-up). Low profile cards are limited to 10W (×16 to 25W). PCI Express Graphics (PEG) cards may increase power (from slot) to 75W after configuration (3.3V/3A + 12V/5.5A).[8] Optional connectors add 75W (6-pin) or 150W (8-pin) power for up to 300W total.
PCI Express Mini Card (also known as Mini PCI Express, Mini PCIe, and Mini PCI-E) is a replacement for the Mini PCI form factor, based on PCI Express. It is developed by the PCI-SIG. The host device supports both PCI Express and USB 2.0 connectivity, and each card may use either standard. Most laptop computers built after 2005 are based on PCI Express and can have several Mini Card slots.
PCI Express Mini Cards are 30×50.95 mm. There is a 52-pin edge connector, consisting of two staggered rows on a 0.8 mm pitch. Each row has 8 contacts, a gap equivalent to 4 contacts, then a further 18 contacts. A half-length card is also specified 30×26.8 mm. Cards have a thickness of 1.0 mm (excluding components).
PCI Express Mini Card edge connector provide multiple connections and buses:
Despite the mini-PCI Express form factor, a mini-PCI Express slot must have support for the electrical connections an mSATA drive requires. For this reason, only certain notebooks are compatible with mSATA drives. Most compatible systems are based on Intel's newest Sandy Bridge processor architecture, using the new Huron River platform.
Notebooks like Lenovo's newest T-Series, W-Series, and X-Series ThinkPads released in March–April 2011 have support for an mSATA SSD card in their WWAN card slot. The ThinkPad Edge E220s/E420s, and the Lenovo IdeaPad Y460/Y560 also support mSATA.[9]
Some notebooks (notably the Asus Eee PC, the MacBook Air, and the Dell mini9 and mini10) use a variant of the PCI Express Mini Card as an SSD. This variant uses the reserved and several non-reserved pins to implement SATA and IDE interface passthrough, keeping only USB, ground lines, and sometimes the core PCIe 1x bus intact.[10] This makes the 'miniPCIe' flash and solid state drives sold for netbooks largely incompatible with true PCI Express Mini implementations.
Also, the typical Asus miniPCIe SSD is 71mm long, causing the Dell 51mm model to often be (incorrectly) referred to as half length. A true 51mm Mini PCIe SSD was announced in 2009, with two stacked PCB layers, which allows for higher storage capacity. The announced design preserves the PCIe interface, making it compatible with the standard mini PCIe slot. No working product has yet been developed, likely as a result of the popularity of the alternative variant.
PCI Express External Cabling (also known as External PCI Express, Cabled PCI Express, or ePCIe) specifications were released by the PCI-SIG in February 2007.[11][12]
Standard cables and connectors have been defined for ×1, ×4, ×8, and ×16 link widths, with a transfer rate of 250 MB/s per lane. The PCI-SIG also expects the norm will evolve to reach the 500 MB/s, as in PCI Express 2.0. The maximum cable length remains undetermined. An example of the uses of Cabled PCI Express is a metal enclosure, containing a number of PCI slots and PCI-to-ePCIe adapter circuitry. This device would not be possible had it not been for the ePCIe spec.
There are several other expansion card types derived from PCIe. These include:
While in early development, PCIe was initially referred to as HSI (for High Speed Interconnect), and underwent a name change to 3GIO (for 3rd Generation I/O) before finally settling on its PCI-SIG name PCI Express. It was first drawn up by a technical working group named the Arapaho Work Group (AWG) that, for initial drafts, consisted only of Intel engineers. Subsequently the AWG expanded to include industry partners.
PCIe is a technology under constant development and improvement. The current PCI Express implementation is version 3.0.
In 2003, PCI-SIG introduced PCIe 1.0a, with a data rate of 250 MB/s and a transfer rate of 2.5 GT/s.
In 2005, PCI-SIG introduced PCIe 1.1. This updated specification includes clarifications and several improvements, but is fully compatible with PCI Express 1.0a. No changes were made to the data rate.
PCI-SIG announced the availability of the PCI Express Base 2.0 specification on 15 January 2007.[13] The PCIe 2.0 standard doubles the transfer rate compared with PCIe 1.0 to 5 GT/s and the per-lane throughput rises from 250 MB/s to 500 MB/s. This means a 32-lane PCI connector (×32) can support throughput up to 16 GB/s aggregate.
PCIe 2.0 motherboard slots are fully backward compatible with PCIe v1.x cards. PCIe 2.0 cards are also generally backward compatible with PCIe 1.x motherboards, using the available bandwidth of PCI Express 1.1. Overall, graphic cards or motherboards designed for v2.0 will work with the other being v1.1 or v1.0a.
The PCI-SIG also said that PCIe 2.0 features improvements to the point-to-point data transfer protocol and its software architecture.[14]
Intel's first PCIe 2.0 capable chipset was the X38 and boards began to ship from various vendors (Abit, Asus, Gigabyte) as of October 21, 2007.[15] AMD started supporting PCIe 2.0 with its AMD 700 chipset series and nVidia started with the MCP72.[16] All of Intel's prior chipsets, including the Intel P35 chipset, supported PCIe 1.1 or 1.0a.[17]
PCI Express 2.1 supports a large proportion of the management, support, and troubleshooting systems planned for full implementation in PCI Express 3.0. However, the speed is the same as PCI Express 2.0. Most motherboards sold currently come with PCI Express 2.0 connectors.
PCI Express 3.0 Base specification revision 3.0 was made available in November 2010, after multiple delays. In August 2007, PCI-SIG announced that PCI Express 3.0 would carry a bit rate of 8 gigatransfers per second, and that it would be backwards compatible with existing PCIe implementations. At that time, it was also announced that the final specification for PCI Express 3.0 would be delayed until 2011.[18] New features for the PCIe 3.0 specification include a number of optimizations for enhanced signaling and data integrity, including transmitter and receiver equalization, PLL improvements, clock data recovery, and channel enhancements for currently supported topologies.[19]
Following a six-month technical analysis of the feasibility of scaling the PCIe interconnect bandwidth, PCI-SIG's analysis found out that 8 gigatransfers per second can be manufactured in mainstream silicon process technology, and can be deployed with existing low-cost materials and infrastructure, while maintaining full compatibility (with negligible impact) to the PCIe protocol stack.
PCIe 2.0 delivers 5 GT/s, but uses an 8b/10b encoding scheme that results in a 20 percent ((10-8)/10) overhead on the raw bit rate. PCIe 3.0 removes the requirement for 8b/10b encoding, and instead uses a technique called "scrambling" that applies a known binary polynomial to a data stream in a feedback topology. Because the scrambling polynomial is known, the data can be recovered by running it through a feedback topology using the inverse polynomial.[20] and also uses a 128b/130b encoding scheme, reducing the overhead to approximately 1.5% ((130-128)/130), as opposed to the 20% overhead of 8b/10b encoding used by PCIe 2.0. PCIe 3.0's 8 GT/s bit rate effectively delivers double PCIe 2.0 bandwidth. PCI-SIG expects the PCIe 3.0 specifications to undergo rigorous technical vetting and validation before being released to the industry. This process, which was followed in the development of prior generations of the PCIe Base and various form factor specifications, includes the corroboration of the final electrical parameters with data derived from test silicon and other simulations conducted by multiple members of the PCI-SIG.
On November 18, 2010, the PCI Special Interest Group officially published the finalized PCI Express 3.0 specification to its members to build devices based on this new version of PCI Express.[21]
AMD latest flagship graphic card, the Radeon 7970, launching in January 9, 2012, will be the world's first PCIe 3.0 graphic card.[22] Although initial reviews suggest that the new interface would not improve graphic performance compared to earlier PCIe 2.0, which at the time of writing, is still under-utilized. However, the new interface would prove advantageous when used for computing purposes.[23]
On November 29, 2011, PCI-SIG has announced to proceed to PCI Express 4.0 featuring 16 GT/s, still on copper technology. Additionally, active and idle power optimizations are to be investigated. Final specifications are expected to be released in 2014/2015.[24]
PCI Express has replaced AGP as the default interface for graphics cards on new systems. Most models of graphics card released in 2009 and 2010 by AMD (ATI) and NVIDIA use PCI Express. NVIDIA uses the high bandwidth data transfer of PCIe for its Scalable Link Interface (SLI) technology, which allows multiple graphics cards of the same chipset and model number to run in tandem, allowing increased performance. AMD has also developed a multi-GPU system based on PCIe called CrossFire. AMD and NVIDIA have released motherboard chipsets that support as many as four PCIe ×16 slots, allowing tri-GPU and quad-GPU card configurations.
PCI Express has displaced a major portion of the add-in card market. PCI Express was originally only common in disk array controllers, onboard gigabit Ethernet, Wi-Fi and graphics cards. Most sound cards, TV/capture-cards, modems, serial port/USB/FireWire cards, network/Wi-Fi cards that would have used the conventional PCI in the past have moved to PCI Express ×8, ×4, or ×1. While some motherboards have conventional PCI slots, these are primarily for legacy cards and are being phased out.
The PCIe link is built around dedicated unidirectional couples of serial (1-bit), point-to-point connections known as lanes. This is in sharp contrast to the earlier PCI connection, which is a bus-based system where all the devices share the same bidirectional, 32-bit or 64-bit parallel bus.
PCI Express is a layered protocol, consisting of a transaction layer, a data link layer, and a physical layer. The Data Link Layer is subdivided to include a media access control (MAC) sublayer. The Physical Layer is subdivided into logical and electrical sublayers. The Physical logical-sublayer contains a physical coding sublayer (PCS). The terms are borrowed from the IEEE 802 networking protocol model.
The PCIe Physical Layer (PHY, PCIEPHY, PCI Express PHY, or PCIe PHY) specification is divided into two sub-layers, corresponding to electrical and logical specifications. The logical sublayer is sometimes further divided into a MAC sublayer and a PCS, although this division is not formally part of the PCIe specification. A specification published by Intel, the PHY Interface for PCI Express (PIPE),[25] defines the MAC/PCS functional partitioning and the interface between these two sub-layers. The PIPE specification also identifies the physical media attachment (PMA) layer, which includes the serializer/deserializer (SerDes) and other analog circuitry; however, since SerDes implementations vary greatly among ASIC vendors, PIPE does not specify an interface between the PCS and PMA.
At the electrical level, each lane consists of two unidirectional LVDS or PCML pairs at 2.525 Gbit/s. Transmit and receive are separate differential pairs, for a total of 4 data wires per lane.
A connection between any two PCIe devices is known as a link, and is built up from a collection of 1 or more lanes. All devices must minimally support single-lane (×1) link. Devices may optionally support wider links composed of 2, 4, 8, 12, 16, or 32 lanes. This allows for very good compatibility in two ways:
In both cases, PCIe negotiates the highest mutually supported number of lanes. Many graphics cards, motherboards and bios versions are verified to support ×1, ×4, ×8 and ×16 connectivity on the same connection.
Even though the two would be signal-compatible, it is not usually possible to place a physically larger PCIe card (e.g., a ×16 sized card) into a smaller slot —though if the PCIe slots are open-ended, by design or by hack, some motherboards will allow this.
The width of a PCIe connector is 8.8 mm, while the height is 11.25 mm, and the length is variable. The fixed section of the connector is 11.65 mm in length and contains 2 rows of 11 (22 pins total), while the length of the other section is variable depending on the number of lanes. The pins are spaced at 1 mm intervals, and the thickness of the card going into the connector is 1.8 mm.[26][27]
| Lanes | Pins | Length | ||
|---|---|---|---|---|
| Total | Variable | Total | Variable | |
| ×1 | 2×18 = 36[28] | 2×7 = 14 | 25 mm | 7.65 mm |
| ×4 | 2×32 = 64 | 2×21 = 42 | 39 mm | 21.65 mm |
| ×8 | 2×49 = 98 | 2×38 = 76 | 56 mm | 38.65 mm |
| ×16 | 2×82 = 164 | 2×71 = 142 | 89 mm | 71.65 mm |
PCIe sends all control messages, including interrupts, over the same links used for data. The serial protocol can never be blocked, so latency is still comparable to conventional PCI, which has dedicated interrupt lines.
Data transmitted on multiple-lane links is interleaved, meaning that each successive byte is sent down successive lanes. The PCIe specification refers to this interleaving as data striping. While requiring significant hardware complexity to synchronize (or deskew) the incoming striped data, striping can significantly reduce the latency of the nth byte on a link. Due to padding requirements, striping may not necessarily reduce the latency of small data packets on a link.
As with other high data rate serial transmission protocols, clocking information is embedded in the signal. At the physical level, PCI Express 2.0 utilizes the 8b/10b encoding scheme[20] to ensure that strings of consecutive ones or consecutive zeros are limited in length. This was used to prevent the receiver from losing track of where the bit edges are. In this coding scheme every 8 (uncoded) payload bits of data are replaced with 10 (encoded) bits of transmit data, causing a 20% overhead in the electrical bandwidth. To improve the available bandwidth, PCI Express version 3.0 employs 128b/130b encoding instead: similar but with much lower overhead.
Many other protocols (such as SONET) use a different form of encoding known as scrambling to embed clock information into data streams. The PCIe specification also defines a scrambling algorithm, but it is used to reduce electromagnetic interference (EMI) by preventing repeating data patterns in the transmitted data stream.
The Data Link Layer performs three vital services for the PCIe express link:
On the transmit side, the data link layer generates an incrementing sequence number for each outgoing TLP. It serves as a unique identification tag for each transmitted TLP, and is inserted into the header of the outgoing TLP. A 32-bit cyclic redundancy check code (known in this context as Link CRC or LCRC) is also appended to the end of each outgoing TLP.
On the receive side, the received TLP's LCRC and sequence number are both validated in the link layer. If either the LCRC check fails (indicating a data error), or the sequence-number is out of range (non-consecutive from the last valid received TLP), then the bad TLP, as well as any TLPs received after the bad TLP, are considered invalid and discarded. The receiver sends a negative acknowledgement message (NAK) with the sequence-number of the invalid TLP, requesting re-transmission of all TLPs forward of that sequence-number. If the received TLP passes the LCRC check and has the correct sequence number, it is treated as valid. The link receiver increments the sequence-number (which tracks the last received good TLP), and forwards the valid TLP to the receiver's transaction layer. An ACK message is sent to remote transmitter, indicating the TLP was successfully received (and by extension, all TLPs with past sequence-numbers.)
If the transmitter receives a NAK message, or no acknowledgement (NAK or ACK) is received until a timeout period expires, the transmitter must retransmit all TLPs that lack a positive acknowledgement (ACK). Barring a persistent malfunction of the device or transmission medium, the link-layer presents a reliable connection to the transaction layer, since the transmission protocol ensures delivery of TLPs over an unreliable medium.
In addition to sending and receiving TLPs generated by the transaction layer, the data-link layer also generates and consumes DLLPs, data link layer packets. ACK and NAK signals are communicated via (DLLP), as are flow control credit information, some power management messages and flow control credit information (on behalf of the transaction layer.)
In practice, the number of in-flight, unacknowledged TLPs on the link is limited by two factors: the size of the transmitter's replay buffer (which must store a copy of all transmitted TLPs until they the remote receiver ACKs them), and the flow control credits issued by the receiver to a transmitter. PCI Express requires all receivers to issue a minimum number of credits, to guarantee a link allows sending PCIConfig TLPs and message TLPs.
PCI Express implements split transactions (transactions with request and response separated by time), allowing the link to carry other traffic while the target device gathers data for the response.
PCI Express uses credit-based flow control. In this scheme, a device advertises an initial amount of credit for each received buffer in its transaction layer. The device at the opposite end of the link, when sending transactions to this device, counts the number of credits each TLP consumes from its account. The sending device may only transmit a TLP when doing so does not make its consumed credit count exceed its credit limit. When the receiving device finishes processing the TLP from its buffer, it signals a return of credits to the sending device, which increases the credit limit by the restored amount. The credit counters are modular counters, and the comparison of consumed credits to credit limit requires modular arithmetic. The advantage of this scheme (compared to other methods such as wait states or handshake-based transfer protocols) is that the latency of credit return does not affect performance, provided that the credit limit is not encountered. This assumption is generally met if each device is designed with adequate buffer sizes.
PCIe 1.x is often quoted to support a data rate of 250 MB/s in each direction, per lane. This figure is a calculation from the physical signaling rate (2.5 Gbaud) divided by the encoding overhead (10 bits per byte.) This means a sixteen lane (×16) PCIe card would then be theoretically capable of 16×250 MB/s = 4 GB/s in each direction. While this is correct in terms of data bytes, more meaningful calculations are based on the usable data payload rate, which depends on the profile of the traffic, which is a function of the high-level (software) application and intermediate protocol levels.
Like other high data rate serial interconnect systems, PCIe has a protocol and processing overhead due to the additional transfer robustness (CRC and acknowledgements). Long continuous unidirectional transfers (such as those typical in high-performance storage controllers) can approach >95% of PCIe's raw (lane) data rate. These transfers also benefit the most from increased number of lanes (×2, ×4, etc.) But in more typical applications (such as a USB or Ethernet controller), the traffic profile is characterized as short data packets with frequent enforced acknowledgements.[29] This type of traffic reduces the efficiency of the link, due to overhead from packet parsing and forced interrupts (either in the device's host interface or the PC's CPU.) Being a protocol for devices connected to the same printed circuit board, it does not require the same tolerance for transmission errors as a protocol for communication over longer distances, and thus, this loss of efficiency is not particular to PCIe.
Theoretically, external PCIe could give a notebook the graphics power of a desktop, by connecting a notebook with any PCIe desktop video card (enclosed in its own external housing, with strong power supply and cooling); This is possible with an ExpressCard interface, which provides single lane v1.1 performance.
IBM/Lenovo has also included a PCI-Express slot in their Advanced Docking Station 250310U. It provides a half-sized slot with an ×16 length slot, but only ×1 connectivity.[35] However, docking stations with expansion slots are becoming less common as the laptops are getting more advanced video cards and either DVI-D interfaces, or DVI-D pass through for port replicators and docking stations.
Additionally, Nvidia has developed Quadro Plex external PCIe video cards that can be used for advanced graphic applications. These video cards require a PCI Express ×8 or ×16 slot for the interconnection cable.[36] In 2008, AMD announced the ATI XGP technology, based on a proprietary cabling solution that is compatible with PCIe ×8 signal transmissions.[37] This connector is available on the Fujitsu Amilo and the Acer Ferrari One notebooks. Only Fujitsu has an actual external box available, which also works on the Ferrari One. Recently Acer launched the Dynavivid graphics dock for XGP.
There are now card hubs in development that one can connect to a laptop through an ExpressCard slot, though they are currently rare, obscure, or unavailable on the open market. These hubs can have full-sized cards placed in them.
Magma and ViDock also makes use of ExpressCard and implements the usage of external graphic solutions .ViDock are expansion chassis tailored specifically for adapting PCI Express graphics cards for use with ExpressCard equipped laptop PCs. This enables user to make use of connecting PCIe cards externally. Although, the developments in these technologies are still ongoing. Other examples that underwent are - MSI GUS, Asus XG Station.
Recently, Intel and Apple introduced Thunderbolt, which allows for external PCI(e) devices.
Several communications standards have emerged based on high bandwidth serial architectures. These include InfiniBand, RapidIO, HyperTransport, QPI and StarFabric. The differences are based on the tradeoffs between flexibility and extensibility vs latency and overhead. An example of such a tradeoff is adding complex header information to a transmitted packet to allow for complex routing (PCI Express is not capable of this). The additional overhead reduces the effective bandwidth of the interface and complicates bus discovery and initialization software. Also making the system hot-pluggable requires that software track network topology changes. Examples of buses suited for this purpose are InfiniBand and StarFabric.
Another example is making the packets shorter to decrease latency (as is required if a bus must operate as a memory interface). Smaller packets mean packet headers consume a higher percentage of the packet, thus decreasing the effective bandwidth. Examples of bus protocols designed for this purpose are RapidIO and HyperTransport.
PCI Express falls somewhere in the middle, targeted by design as a system interconnect (local bus) rather than a device interconnect or routed network protocol. Additionally, its design goal of software transparency constrains the protocol and raises its latency somewhat.
When developing and/or troubleshooting the PCI Express bus, examination of hardware signals can be very important to find the problems. Logic analyzers and bus analyzers are tools that collect, analyze, decode, store signals so people can view the high-speed waveforms at their leisure.
|
|||||||||||||||||||||||