Supermarine Spitfire (late Merlin powered variants)

Spitfire
Supermarine Spitfire VIII in the markings of 457(RAAF) Sqn
Role	Fighter / Photo Reconnaissance
Manufacturer	Supermarine
Designed by	Joseph Smith
First flight	September 1941 (Mk III with Merlin 61)
Introduction	June 1942 (Mk IX)
Retired	1955, RAF
Primary user	Royal Air Force
Produced	1942–1945
Number built	8,996 (20,346 total)[1]
Variants	Seafire, Spiteful, Seafang

Spitfire L.F Mk. IX MH434 of Duxford's Historic Aircraft Collection.

The British Supermarine Spitfire was facing several challenges by mid-1942. The debut of the formidable Focke-Wulf Fw 190 in late 1941 had caused problems for RAF fighter squadrons flying the latest Spitfire Mk Vb.^[2] By this time Rolls-Royce engineers were already working on a new version of the Merlin incorporating two-stage superchargers; the combination of the improved Merlins and the Spitfire Mk VC airframe in a "stop-gap" design allowed the RAF to combat the Fw 190 on equal terms. In a second stream of development Supermarine was working on an improved, reinforced Spitfire airframe which incorporated several new features and was designed specifically for the Merlin 60 and 70 series engines.^[3] This new airframe later formed the basis for the Rolls-Royce Griffon powered Spitfires.

This article presents a history of the Spitfire powered by two-stage engine variants and also describes some of the "drawing board" projects and experimental Spitfires. The Griffon powered variants are described in a separate article.

Wing types

The majority of the Spitfires from the Mk VIII on, used three basic wing types; C through to the E types

C type

Also known as the "universal wing" the new design was standard on the majority of Spitfires built from mid 1942. This wing was structurally modified to reduce labour and manufacturing time plus it was designed to allow mixed armament options; A type, B type, or four 20 mm Hispano cannon.^[4]

The undercarriage mountings were redesigned and the undercarriage doors were bowed in cross section allowing the legs to sit lower in the wells, eliminating the upper-wing blisters over the wheel wells and landing gear pivot points. Stronger undercarriage legs were raked 2 inches (5.08 cm) forward, making the Spitfire more stable on the ground and reducing the likelihood of the aircraft tipping onto its nose.^[4]

The Hispano Mk IIs fitted in all cases were now belt fed from box magazines allowing for 120 rpg (the "Chattellerault" system). The fairings over the Hispano barrels were shorter and there was usually a short rubber stub covering the outer cannon port. Redesigned upper wing gun bay doors incorporated "teardrop" shaped blisters to clear the cannon feed motors, and the lower wings no longer had the gun bay heating vents outboard of the gunbays. The first series of Spitfire Mk IXs retained the bay doors first used on Spitfire VCs; these incorporated large blisters to clear the feed motors of two Hispano cannons. All later Spitfires had smaller, more streamlined blisters.^[4] In order to provide room for the belt feed system of the cannon the inner machine gun bays were moved outboard to between ribs 13 and 14.^[4]

Because the Spitfire was no longer to be used as a nightfighter the retractable landing lights were no longer fitted.^[4]

Several versions of the Spitfire, starting with the H.F Mk VIIs had extra 13 gallon integral fuel tanks added to the wing leading edges between the wing-root and the inboard cannon bay.^[5].

Although many earlier Spitfires had been modified to carry bomb racks capable of carrying 250 lb (113 kg) bombs the first Spitfires to be specifically modified for the fighter-bomber role (known as Modification 1209) were those of the Second Tactical Air Force. The first Mk IX Spitfires started being used in the role in June 1944.^[6]

D Type

These were made for the Photo-Reconnaissance Spitfires; no armament was fitted and the "D" shaped leading edges of the wings, ahead of the main spar, were adapted to become integral fuel tanks. These were fitted to the Mk X and XI.

E type

Structurally unchanged from the C wing. The outer machine gun ports were eliminated, although the outer machine gun bays were retained and their access doors were devoid of empty shell case ports and shell deflectors. The inner gun bays allowed for two weapon fits;

• 2 × 20 mm Hispano Mk II cannon with 120 rpg in the outer bays.
• 2 × .50 cal Browning M2 machine guns, with 250 rpg in the inner bays.

or

• 4 × 20 mm Hispano cannon with 120 rpg^[4]

The .303 machine guns mounted in the outer wings were no longer fitted as most aircraft at that time had armour impenetrable by .303 bullets. During a turning combat the effectiveness of the outboard machine guns was low because if the aircraft was pulling 'g' the flexing of the wings meant that the rounds scattered in a large cone. The 20 mm Hispano cannon were moved outboard and a more effective .50 calibre Browning .50 cal M2/AN heavy machine gun with 250 rpg was added to the inner gun-bay. The first trial installation of the installation (modification 1029) was made in BS118 in November 1943; by mid-March 1944 the first Spitfires to be modified were from 485(NZ), 222 and 349 Squadrons. Spitfires with this armament were referred to as Spifire IX LF .5 and the E suffix was not officially introduced until early 1945. This armament was standard for all Spitfire Mk IXs and XVIs used by the 2nd Tactical Air Force as fighters and fighter-bombers from shortly after D-Day.^[6] The improved armament was more effective for both air-to-air engagements and air-to-ground attacks.^[7].

Many Spitfires had their rounded wingtips replaced by shorter, squared off fairings to improve low-altitude performance and enhance the roll rate. These are sometimes referred to as "L.F" versions, e.g. L.F.IX. This designation referred to the low-altitude version of the Rolls-Royce Merlin engine and while many "L.F" Spitfires had the "clipped" wings, a number did not.

Variants

Mark numbers, type numbers

The Mark numbers did not necessarily indicate a chronological order; for example, the Mk IX was a stopgap measure brought into production before the Mks VII and VIII. In addition, some Spitfires of one mark or variant may have been modified to another; for example, several of the first Mk VBs were converted from Mk IBs; the first Mk IXs were originally Mk VCs, converted, in some instances, by Rolls-Royce at their Hucknall facility.

Up until the end of 1942, the RAF always used Roman numerals for mark numbers. 1943-1948 was a transition period during which new aircraft entering service were given Arabic numerals for mark numbers but older aircraft retained their Roman numerals. From 1948 onwards, Arabic numerals were used exclusively. This article adopts the convention of using Roman numerals for the Mks I-XVI and Arabic numerals for the Mks 17-24. Type numbers e.g.; (type 361) are the drawing board design numbers allocated by Supermarine.^[8].^[9]

Features of late Merlin powered Spitfires

With the development of the Merlin 61/63/66 and 70 series engines, with a two-stage, two-speed supercharger requiring an intercooler, several important modifications were made to the basic airframe and applied to all aircraft powered by these engines. The longer Merlin 61 meant the nose forward of the engine/fuel tank bulkhead was 7 inches (17.8 cm) longer. An intercooler was mounted behind the engine, on the supercharger casing. A small rectangular air scoop for a "Heywood" air compressor was fitted on the starboard upper engine cowling.

The carburettor air intake on early to mid-production Spitfire IXs was a different shape to those of single-stage engined aircraft; they were shorter and had a wider air inlet. From 1943, an "Aero-Vee" tropical filter in a long, streamlined fairing was introduced for the carburettor air intake. This was fitted as standard to all Mk VIIs, VIIIs, P.R Mk Xs and Mk XVIs, on mid to late production Mk IXs, and to most P.R Mk XIs.

A new 10 ft 9 in (3.27 m) diameter four bladed Rotol propeller was fitted, housed in a pointed spinner. The exhaust units were changed to six "fishtail" stacks per side. Under the nose, the three piece cowling was changed to a one piece layout. The oil tank was no longer a part of the cowling structure. Early Mk IXs had a teardrop shaped blister for a Coffman engine starter^[a] on the lower starboard side cowling, just behind the propeller. This was replaced by an improved electric starter on most two-stage Merlin powered Spitfires and, from late 1942 the blister was only seen on a few aircraft

The Type C wing was fitted as standard. Some mid and most late production Spifire Mk IXs and all Mk XVI were fitted with the Type E wing. While Spitfire IXs converted from Mk VCs had the large teardrop fairings on the upper surfaces, on the majority of Mk VIIs, VIIIs, IXs and XVIs the teardrop shaped blisters covering the Hispano feed motors were reduced in size and more streamlined than those on the Mk VC. According to A.P 1565J P & L (Spitfire IX, XI and XVI Pilot's Notes) the red painted undercarriage indicator rods, which projected through the tops of the wings when the undercarriage was down, were used only on early production Mk IXs. When fitted these rods supplemented an "Electric visual indicator" mounted on the instrument panel.^[10] The indicator rods seemed to be fitted on all Mk VIIs and VIIs, supplementing the electric visual indicator. A light for the retractable tailwheel was mounted on the instrument panel, just below the main visual indicator^[11][12].

Because the intercooler required a radiator, the radiator under the starboard wing was halved in size and the intercooler radiator housed alongside. Under the port wing a new radiator fairing housed a square oil cooler alongside of the other half-radiator unit. When the engine was running at low speed, one radiator section provided enough coolant; a thermostatic switch turned off the starboard radiator section until more power was called for and extra engine cooling was required^[13].

Other structural changes included flush riveting for the fuselage, which was introduced in mid-1943. A streamlined round rear-view mirror, with a bullet-shaped fairing replaced the rectangular version. On new production Mk IXs the small, teardrop shaped identification light behind the radio mast was removed.

While early Mk IXs converted from Mk VCs had the original size elevator horn mass-balances most had the enlarged version with the straightened leading edge. A new rudder of greater area, which could be identified by a "pointed" tip, was fitted to Mk VIIs, Mk VIIIs, and mid to late production Mk IXs and Mk XVIs.

All Mk VII and Mk VIII Spitfires had the following changes: The internal structure was strengthened and revised. On the wings the ailerons were reduced in span by 8.5 inches (220 mm) outboard of the outer hinges. There had been some instances of earlier models breaking up in the air in steep high speed dives, it was thought, because of aileron flutter.^[b] In addition a 13 gal (64 l) fuel tank was fitted in each wing leading edge between the wingroot and the inner gun-bay.

The main fuselage fuel tanks were increased in capacity; 47 gal (213.7 l) for the upper tank and 49 gal (222.7 l) for the lower. In combination with the wing tanks this gave a total internal capacity of 122 gal (554.6 l), a near 50% increase over the 85 gal (386.4 l) carried by earlier Spitfire marks.^[14]

The main undercarriage legs, for the first time in the Spitfire's life, were fitted with forward facing torque links. In addition, the leg doors were slightly concave, allowing the undercarriage to sit lower in the wheel wells when retracted: this meant the upper wing skinning was free of the small bulge which had hitherto been necessary to clear the wheels. The wheels themselves were a new strengthened Dunlop AH10019 "four spoke" pattern, replacing the "five spoke" pattern used since the first Mk Is. This revised undercarriage was also fitted on some mid to late Mk IXs and all Mk XVIs.^[15] A retractable tailwheel (Dunlop 2184) was fitted, covered by small doors when in flight. This also applied to the P.R Mk Xs and most P.R Mk XIs.

Spitfire H.F Mk. VII EN474 was tested by the USAAF and is now housed at the Smithsonian National Air and Space Museum, the only surviving example of a Mk VII. Note the "pointed", extended wingtips and the cabin pressurisation air intake under the exhausts.

Mk VII (type 351)

Like the Mk VI, the Mk VII was a high altitude pressurised variant, this time powered by the Merlin 64 or 71 series engine with two-stage, two speed superchargers. The cockpit was pressurised in a similar way to that of the Mk VI, although the details were slightly different. Other changes to the airframe are noted above. The Mk VII used a Marshall manufactured compressor for pressurising the cockpit; this was mounted on the right of the engine and drew its air through a long intake under the starboard exhaust stubs. An automatic valve allowed a maximum pressure differential of +2 lb./sq.in. This was built up during the climb and was maintained at heights of 28,000 ft and above^[16].

Extended, "pointed" wingtips were fitted to the Type C wings, increasing the wingspan to 40 ft 2 in (12.2 m). Because the threat from high altitude bombers never materialised many Mk VIIs later reverted to the normal, rounded wingtip.

While early Mk VIIs were fitted with a detachable canopy, secured by four pilot operated catches, later Mk VIIs were fitted with a "Lobelle" type hood which opened by sliding backwards, as on non-pressurised versions of the Spitfire. This was a big improvement on the clamp down cockpit of the Mk VI. The canopy was double-glazed and used rubber tubing to create a proper pressure seal against the fuselage. The canopy rails were bulkier than the standard Spitfire type^[16][17].

In total, 140 Mk VIIs were built by Supermarine. All were powered by the Merlin 64 (F. Mk VII) or Merlin 71 (HF. Mk. VII), the latter fitted with a Bendix-Stromberg "anti-g" carburettor^[18]. The H.F Mk had superb high altitude performance, with a service ceiling of 45,100 feet (13,700 m); French ace Pierre Clostermann recalls in his book, The Big Show, the successful interception of a long-range reconnaissance Messerschmitt Bf 109G-6/R3 by a Mk VII 'Strato Spitfire' of 602 Squadron at 40,000 feet (12,000 m) over the British Home Fleet's base at Scapa Flow in early 1944.

Mk VIII (type 360)

Spitfire Mk VIII

The Mk VIII was an adaptation of the Mk VII without the pressurised cabin, and was intended to become the main production model of the Spitfire. When the "interim" Mk IX proved itself to be adequate for the RAF's needs it was decided to utilise the shadow factory at Castle Bromwich to produce that version only: the Mk VIII Spitfires were all built by Supermarine.

Apart from the lack of pressurisation, the Mk VIII differed little from the Mk VII. Some early production models had extended wingtips but the majority were fitted with the standard version. There were three sub-variants for low altitude (LF Mk VIII), medium altitude (F Mk VIII) and high altitude (HF Mk VIII) which were powered respectively by the Merlin 66, Merlin 63 and Merlin 70 engines^[18].

According to Jeffrey Quill, who was Vickers Supermarine's chief test pilot and was instrumental in test flying and assessing every development of the Spitfire from the prototype K5045 to the last production Mk 24:

When I am asked which mark of Spitfire I consider the best from the flying point of view, I usually reply 'The Mark VIII with standard wingtips.' I hated the extended wingtips...They were of no practical value to the Mark VIII and simply reduced the aileron response and the rate of roll.^[19]

The F Mk VIII's top speed was 408 mph (657 km/h) at 25,000 ft (404 mph for the LF.Mk VIII at 21,000 ft (6,400 m) and 416 mph (669 km/h) for the HF.Mk VIII at 26,500 ft), with a service ceiling of 43,000 ft (41,500 ft for the LF Mk VIII and 44,000 ft (13,000 m) for the HF.Mk VIII). The two main tanks were given an extra 11 gal for a total of 96 gal which, along with the wing tanks, allowed the fighter to fly for a maximum distance of 660 miles (1,060 km) with a full internal fuel load and 1,180 miles (1,900 km) with a full internal load and a 90 gal drop tank. Provision was made to allow the Mk VIII to carry a single "slipper" drop tank of 30, 90 or 170 gal capacity. With a 170 gal tank, the aeroplane could fly over 1,500 miles (2,400 km). When carrying the 90 or 175 gal tank the aircraft was restricted, once airborne and at cruising altitude, to straight and level flight<^[5]

A maximum external bomb load of 1,000 pounds (1 × 500 lb (230 kg) bomb attached to the centre bombrack plus 2 × 250 lb (110 kg) bombs, one under each wing) could be carried.

A Mk VIII JF299 was used to experiment with the use of a new cut-back rear fuselage and a "tear-drop" canopy. This was intended to aid pilot visibility; many Spitfire pilots who were shot down were done so by enemies who approached in the aircraft's blind spot. In trials, the new hood design was found to bring about great improvements to all-round visibility and, with several modifications, was standardised on later Spitfires^[20].

This variant served almost exclusively overseas in the Mediterranean, with both the Desert Air Force and the USAAF, in the Pacific, with the Royal Australian Air Force and with the RAF in the China-Burma-India theatre. After the Mk IX and Mk V, the Mk VIII was the third most numerous operational variant with 1,658 examples.^[19]

Mk IX (type 361)

BS456 UZ-Z of 306(Polish) Toruński Squadron, RAF Northolt, November 1942. A Spitfire IX converted from a Mk VC airframe. A teardrop shaped blister for a Coffman cartridge starter can be seen just behind the propeller. This aircraft carries a 30 gallon "slipper" drop tank under the fuselage.

In the early months of 1942, with the clear superiority of the Focke Wulf Fw 190 over the Spitfire VB, there was much pressure to get Spitfires into production using the new two-stage supercharged Merlin 61 engine. In September 1941 the Spitfire Mk III prototype N3297 had been converted by Rolls-Royce at their Hucknall plant to take a Merlin 60, which had been specifically designed for use in the Wellington Mk VI high altitude bomber.

The performance increase was described as a "quantum leap" over that of the Mk VB and another Spitfire airframe, R6700 was modified to take the new engine. Although design work on the Mk VII and VIII series was under way, these would take over a year to get into production and a counter to the Fw 190 was urgently needed. As a result the Air Ministry made the decision that Mk VC airframes should be converted to take the more powerful engine^[21][22].

As a result many of the early IXs were converted Mk VCs which did not have any of the refinements which later appeared. These could be identified by the Type C wing with the large double blisters over the inner cannon bays and the identification light on the fuselage spine, behind the aerial mast. The elevator horns were also smaller in size than that of most Mk IXs which had larger horn balances.^[c]

The first IX was a modified VC (AB505). It was tested by the AFDU in April 1942. The report said;

The performance of the Spitfire IX is outstandingly better than the Spitfire V especially at heights above 20,000 feet. On the level the Spitfire is considerably faster and climb is exceptionally good. It will climb easily to 38,000 feet and when levelled off there can be made to climb in stages to above 40,000 feet by building up speed on the level and a slight zoom. Its manoeuvrability is as good as a Spitfire V up to 30,000 feet and above and is very much better. At 38,000 feet it is capable of a true speed of 368mph and is still able to manoeuvre well for fighting.^[23]

Although the Mk IX's airframe did not have the aerodynamic and strength improvements, or the modified control surfaces of the Mk VII and VIII, the Mk IX still proved to be an effective counter to the Focke Wulf Fw 190; production of the Mk IX ended in April 1945 and, in combination with the Mk XVI this "compromise" was produced in larger numbers than any other Spitfire variant.

Early Mark IXBs of 611 Squadron based at Biggin Hill in late 1942. Note the large cannon blisters and ID lights behind the mast, denoting converted Mk Vcs.

In September 1942, the "High Altitude Flight" was set up at RAF Northolt to counter the threat of the high altitude Junkers Ju 86 R bombers. Two Spitfire XIs converted from VCs were stripped of armour, the .303 Brownings and other equipment and repainted in a lightweight PRU blue finish. One of them successfully intercepted a Ju 86R at over 40,000 feet (12,000 m).

Production of the Mk IX finished at Supermarine in June 1943, with production continuing exclusively at the Castle Bromwich factory. Several major and large numbers of minor improvements were progressively introduced to Mk IXs, some of which were used on other Spitfire variants.

The Merlin 61 was phased out early in 1943 in favour of the Merlin 63 and 63A^[24]. The new engine had increased power resulting from engine improvements and engine limitations of +18 lbs./sq.in and 3,000 rpm (5 minute combat). During the second half of 1943, production of the Merlin 63 powered F. Mark IX was discontinued in favour of the Merlin 66 powered L.F. Mark IX^[25]. Early production Spitfire IXs suffered from vapour locks in the fuel lines resulting from fuel evaporating if the aircraft was parked in direct sunlight. As a result of this the gun-camera was moved from the port wingroot to the starboard wingroot and a fuel cooler, fed by a small round air-intake was fitted in its place. This fuel cooler was also fitted to early PR Mk XIs^[26]

Production of the L.F. Mk IXs, frequently referred to as the Spitfire IXB, initially ran in parallel with the Merlin 63 powered Marks. This version first became operational in March 1943 with the Biggin Hill Wing, comprised at the time of 611 and 341(Free French) Squadrons. This type was by far the most produced of the Spitfire IX variants, with over 4000 built. The maximum power of the Merlin 66 was 1,720 hp (1,280 kW) at 5,750 ft (1,283 kW at 1,752 m) and the maximum speed of the Spitfire LF IX was 404 mph (650 km/h) at 21,000 feet (6,400 m)^[27]. The Merlin 66 introduced a new Bendix-Stromberg injection carburettor, which replaced the earlier S.U float carburettor^[24].

The H.F IX was powered by the specialised high altitude Merlin 70 and entered service in the Spring of 1944. Serial listings show that the H.F Mk IX was produced in relatively limited numbers when they were required, with priority being given to versions rated for low and medium altitudes^[28][29]. Maximum power of the Merlin 70 was 1,710 hp (1,280 kW) at 11,000 ft (1,275 kW at 3,353 m): maximum speed of the Spitfire H.F.IX was 405 mph (652 km/h) at 25,400 feet (7,700 m) at an all-up weight of 7,320 lbs (3,320 kg)^[30].

The cockpit of a Spitfire IX showing the instrument panel and the Mk II Gyro gunsight.

Also introduced in early 1944 was a new Mark II Gyro gunsight. This gunsight calculated the correct angle of deflection to use when leading the target. Its introduction doubled the effectiveness of RAF gunnery and was a major factor in Allied air superiority^[31].

The capacity of the main fuel tanks was 48 gal for the upper tank and 37 gal for the lower, for a total internal capacity of 85 gal. Jettisonable "slipper tanks" of 30, 45 or 90 gal could be carried under the centre-section^[32]. As an alternative a cylindrical 50 gal drop tank, adapted from those carried by long range Hawker Typhoons, could be carried on the fuselage bomb rack used on most Mk IXs of the Second Tactical Air Force. To further increase the combat radius some late production Mk IXs were fitted with additional internal self-sealing fuel tanks in the rear fuselage: the upper tank carried 41 gal and the lower 34 gal. When both were full this enabled a ferry range of over 1,200 miles (1,900 km), although they made the aircraft unstable in flight and only straight flight and gentle manoeuvres at low altitudes were recommended by the pilot's manual. The pilot was also warned to avoid instrument flying whenever possible^[33][34].

Late production Mk IXs, in common with Mk XVIs introduced a new upper engine cowling which incorporated a distinct bulged top surface; this design was adopted for the Mk XVI to allow for the modified intercooler of the Packard Merlin 266, which had an integral header tank.

The cut-down rear fuselage and bubble canopy, trialled on a Spitfire Mk VIII, was incorporated into very late production Mk IXs. With the cut down fuselage the lower forward fuselage tank capacity was increased to 47 gal while the rear fuel tanks were decreased to a capacity of 66 gal^[32]. These were the rarest of the Mk IXs and many of them featured the "clipped" wings. The great majority of these saw postwar service with the SAAF, both in South Africa and in deployment in Korea during the 1950s.

During early 1945, some Spitfire IXEs and XVIEs of 74 Squadron were fitted with a single RP-3 rocket under each wing. This was believed to be the only RAF Spitfire unit to use rockets operationally during the Second World War.^[35]

PR Mk IX (type 374) and FR Mk IX

Pending development of a dedicated Merlin 61 powered PR Spitfire (the Mk XI) at least three Mk IXs (BS338, BS339 and BS473) were taken off the production line and modified by to carry two vertical cameras in the rear fuselage. The first of these was delivered to 541 Squadron at RAF Benson on 30 November 1942. Subsequently another 15 Mk IXs were converted to PR Mk IXs (factory designation type 374) at the Vickers-Armstrong Worthy Down facility. As well as incorporating camera equipment, a wrap-around PR type windscreen was fitted and a larger oil tank was installed under the nose. All armament was removed and a PRU Blue finish applied. These aircraft lacked the "wet wing" tanks, meaning that the PR IX relied on drop tanks for extra range. The most famous PR Mk IX missions involved carrying out reconnaissance missions in preparation for Operation Chastise, the 617 "Dambusters" Squadron attacks on the Ruhr dams. A PR Mk IX photographed the dams the day before the operation and photographed the Moehne Dam after the operation^[36].

FR IXs were standard, armed Mk IXs modified with a single, port facing, oblique camera. These aircraft were used for low altitude "Dicing" missions in tactical support of army operations. 16 Squadron, which was a unit of the 2nd TAF, used several FR Mk IXs (painted a pale, "Camoutint" Pink, which provided excellent camouflage under cloud cover) to photograph the Arnhem area before and during Operation Market Garden.Another unit using FR Mk IXs was 318(Polish) "City of Gdańsk" Fighter-Reconnaissance Squadron based in the Mediterranean^[37].

Mk T. IX and TR. 9 (type 509)

TR 9 "Grace Spitfire" at RIAT 2004.

Although there were wartime conversions of the Spitfire into a two-seat trainer including the one-off modification of a Mk VC by RAF no. 261 Squadron and a Mk IX converted for use as a trainer by the Soviets, the two-seat Spitfire trainer was primarily a postwar program. In 1946, a MK VIII (MT818) was the first Vickers-built trainer built as a demonstrator, but in 1948, 10 Spitfire T Mk IXs, were exported to India. In 1951, a further six TR 9 trainers were converted from the standard Mk IX to train pilots for the Irish Air Corps (IAC) Seafire fleet. The Spitfires provided transition training that included gunnery practice since the type was equipped with two .303 Browning machine guns, one in each outer wing bay. Most of the TR 9 aircraft passed to the ground technical training school at Baldonnel where they were used as instructional airframes for the training of aircraft engineers for the Air Corps. Four of the IAC aircraft survived and two went on to join the warbird fleet in the 1970s and later.

The Mk IX was the second most numerous variant of Spitfires produced. In total, 5656 were built, 561 by Supermarine and 5,095 by Castle Bromwich.

Spitfire P.R Mk XI in 2008

PR Mk X and PR Mk XI (types 387, 365 and 370)

When development started on new Merlin 60 powered Spitfires, both the Mk VII and VIII were to have photo-reconnaissance (PR) variants. On 21 April 1942, an order was placed for 70 aircraft, provisionally designated PR Mk VIII. Based on the revised MK VIII airframe these aircraft were to be powered by Merlin 61s and were assigned serial numbers LV643-681 and LV726-756. The Spitfires bearing these serials were eventually built as Merlin 66 LF Mk VIIIs^[38].

A policy change resulted in the pressurised PR variant of the Mk VII being renamed PR Mk X (type 387). This version followed the PR Mk XI into production and was based on the Mk VII airframe with PR Mk XI wings and camera installation. It had the pressurised Mk VII cockpit, with the Lobelle sliding canopy, and retained the fighter style windscreen with the bullet-proof glass panel. The long thin air intake to the cockpit pressurisation system was fitted under the exhaust stacks on the starboard cowling. The performance was similar to that of the PR XI although the pressurised cockpit meant that this version could stay at altitudes of over 40,000 ft for longer without the exhausting physiological effects experienced by the pilots of unpressurised cockpits^[39]. Sixteen Mk Xs were built during April and May 1944, with the first mission being flown on 11 May. All saw limited service in 541 and 542 Squadrons in a high altitude reconnaissance role. Experience with this version led to the development and production of the pressurised version of the PR Mk XIX^[40].

The Mk XI (type 365 standard, type 370 tropicalised) was based on a combination of features from the marks VII, VIII and IX. The Mk XI was the first PR variant to have the option of using two vertically-mounted F52 cameras with 36 inch focal length lens in the fuselage behind the cockpit^[41]. Several other configurations could be fitted, depending on mission requirements; the "X Type" installation, for example had two vertically mounted F24s with 14 inch lens and an oblique F24 with an 8 inch lens mounted above and facing to port^[42]. PR Mk XIs used for tactical reconnaissance had an additional, vertically oriented camera in a fairing under each wing^[41].

Physically the Mk XIs had a deeper nose fairing to accommodate a larger 14.5 gal oil tank and used the unarmoured, wrap-around PRU windscreen. "Booster" pumps for the wing tanks were fitted and covered by "teardrop" shaped fairings under the wings. Retractable tailwheels were fitted as standard and the majority of the Mk XIs built had the later large area "pointed" rudder. 260 Mk XIs were powered by Merlin 61, 63 or 63A engines while the remaining 211 used the high altitude Merlin 70. All of the Merlin 70 and 198 of the Merlin 60 series aircraft were fitted with the Vokes Aero-Vee dust filter in the extended, streamlined carburettor air intake under the nose^[41]. All Merlin 60 powered aircraft featured the fuel cooler in the port leading edge wing root. The radio installation was either the VHF TR.1133 or TR.1143 fitted with the "Rebecca" beam approach equipment^[41].

Additional "slipper" drop tanks could be fitted under the centre-section; in common with the Mk IX these could be 30, 45 or 90 gal capacity and, for the Mk XI, a tank of 170 gal capacity was also available^[32].

Spitfire PR Mk XIs were capable of a top speed of 417 mph (671 km/h) at 24,000 ft (7,300 m) and could cruise at 395 mph (636 km/h) at 32,000 ft (9,800 m). Normally Spitfire XIs cruised between these altitudes although, in an emergency, the aircraft could climb to 44,000 ft (13,000 m) However, pilots could not withstand such altitudes for long in a non-pressurised cockpit without suffering from serious physiological effects^[39].

At first, production of the PR Mk XI was delayed because development of the Mk VII and VIII series was delayed. As a result it was decided to base the Merlin 60 powered PR aircraft on the MK IX airframe^[38]. Production was further threatened because of a dispute over RAF PR doctrine: in early 1943, because the new PR Spitfire was delayed, the Air Ministry proposed that all PR units be converted to de Havilland Mosquitoes. After further analysis the Air Staff agreed that Mosquitoes could perform 90% of PR missions so the Spitfire production for only 10% of PR units was mooted. Air Vice Marshal John Slessor, head of Coastal Command pointed out that the Spitfire was smaller than the Mosquito, used half the number of Merlin engines and was faster, more manoeuvrable and quieter and, therefore production should be increased, not reduced. As a result the Air Staff decided that PR Mk XI production should be accelerated at the cost of the fighters^[41].

The first Mk. XIs were built in November 1942: from April 1944 production ran concurrently with the PR Mk XIX before ending in December 1944, when they were phased out in favour of the Mk XIX. In total 471 Mk XI were built by Supermarine^[43].

PR Mk XIII

The PR Mk XIII was an improved PR Type G with a single-stage Merlin engine and is described in Supermarine Spitfire (early Merlin powered variants)

Mk XVI (type 361)

A late Spitfire Mk XVIE with the teardrop canopy.This is TD248, currently flying at Duxford.

The Mk XVI was the same as the Mk IX in nearly all respects except for the engine, a Merlin 266. The Merlin 266 was the Merlin 66 and was built under licence in the USA by the Packard Motor Company. The "2" was added as a suffix in order to avoid confusion with the engines, as they required different tooling. All Mk XVI aircraft produced were of the Low-Altitude Fighter (LF) variety. This was not determined by the length of the wings (clipped wings were fitted to most LF Spitifres), but by the engine, which had been optimised for low-altitude operation. All production Mk XVIs had clipped wings for low altitude work and were fitted with the rear fuselage fuel tanks with a combined capacity of 75 gal^[32]. Many XVIs featured cut-down rear fuselages with "bubble" canopies. On these aircraft the rear fuselage tank capacity was limited to 66 gal^[32].

Because of a slightly taller intercooler and rearranged accessories on the Packard Merlins a new, bulged upper cowling was introduced and also appeared on late production IXs^[44].

Armament for most Mk XVIs consisted of 2 × 20 mm Hispano II cannon - each with 120 rpg - and 2 × .50 calibre Browning machine guns - each with 250 rpg. 1 × 500 lb (227 kg) bomb could be carried underneath the centre rack, and 1 × 250 lb (114 kg) bomb could be slung under each wing. Some production aircraft had rear fuselage fuel tanks in addition to the main tank which allowed it to fly approximately as far as the Spitfire Mk VIII. Problems with the licence-built engines limited introduction to front-line squadrons for several months. A total of 1,054 Mk XVIs were built by Castle Bromwich.

Spitfire Floatplanes (types 355 & 359)

The Spitfire Vb floatplane W3760

With the German invasion of Norway in April 1940 the RAF took an interest in the concept of using floatplane fighters in areas where airfields were not immediately available. To this end a Spitfire Mk I R6722 was taken in hand at the Woolston factory to be modified and mounted on Blackburn Roc floats. Tank tests were carried out at Farnborough, using a 1/7th scale model, it was found that the concept was basically sound, although the vertical tail surfaces would need to be enlarged to counter-balance the side area of the floats. The end of the Battle of Norway and the need for as many Spitfires as possible meant that R6772 was converted back to an ordinary fighter without being flown^[45][46]

With the entry of Japan into the war the concept was revived in early 1942. A Spitfire V W3760 was fitted with a pair of floats 25 ft 7 in (7.8 m) long, mounted on cantilever legs. This aircraft was powered by a Merlin 45 driving a four bladed propeller of 11 ft 3 in (3.43 m) diameter (3.4 m). A Vokes filter was fitted to the carburettor air intake and under the tail an extra fin extension was added. Other changes included external lifting points forward of and behind the cockpit and a spin-recovery parachute with a rudder balance-horn guard. The Spitfire floatplane was first flown on 12 October 1942 by Jeffrey Quill. Soon afterwards the Vokes filter was replaced by an Aero-Vee filter, similar to that on later Merlin 61 series aircraft, which was extended to prevent water entry, and full Mk VB armament was installed. Two more VBs EP751 and EP754 were converted by Folland and all three floatplanes were transported to Egypt, arriving in October 1943. At the time it was thought that the floatplanes could operate from concealed bases in the Dodecanese Islands, disrupting supply lines to German outposts in the area which relied on resupply by transport aircraft. This scheme came to naught when a large number of German troops, backed by the Luftwaffe, took over the British held islands of Kos and Leros. No other role could be found for the floatplane Spitfires, which languished in Egypt, operating from the Great Bitter Lake. Specifications for the VB based floatplane included a maximum speed of 324 mph (521 km/h) at 19,500 ft (521 km/h at 5,943 m), a maximum rate of climb of 2,450 ft/min at 15,500 ft (12.45 m/s at 4,724 m) and an estimated service ceiling of 33,400 ft (10,180 m)^[d][47].

In the spring of 1944, with the prospect of use in the Pacific Theatre, a Spitfire IX MJ892 was converted to a floatplane. This used the same components as the earlier Mk VB conversions. Jeffrey Quill wrote:

"The Spitfire IX on floats was faster than the standard Hurricane. Its handling on the water was extremely good and its only unusual feature was a tendency to "tramp" from side to side on the floats, or to "waddle" a bit when at high speed in the plane."

Soon after testing started the idea of using floatplane fighters was dropped and MJ982 was converted back to a landplane.^[48]

Five aircraft were converted:

• Mk I - R6722
• F.Mk Vb - W3760
• Mk V - EP751 and EP754
• Mk IXb - MJ892 ^[49][50]

Drawing board projects

• Supermarine 305: Designed to the same specification as the Boulton Paul Defiant and Hawker Hotspur. The basic Spitfire wings and undercarriage were mated to a new fuselage which provided room for a gunner and a remote control four gun turret (originally armed with .303 Brownings, later with Lewis machine guns.) Other modifications included a cooling system mounted in a chin radiator housing. There was no forward firing armament and dive brakes were added to the wings. Projected speed 315 mph (507 km/h) at 15,000 ft (4,572 m).^[51]
• Supermarine 312: This was the basic Mk I Spitfire adapted to take four 20 mm Oerlikon cannon mounted in modified wings. The radiator and oil cooler were moved from under the wing to a duct under the fuselage. This was R J Mitchell's last design before his death in 1937.^[52]
• Supermarine 324, 325 and 327: These were designs for twin-engined fighters which used the same construction techniques and the same elliptical wing planforms as the Spitfire. All three designs used tricycle undercarriages with the primary engines being Merlins with an alternative being the Bristol Taurus. The 324 and 325 were intended to carry an armament of 12 .303 calibre Brownings in groups of six in each outer wing while the 327 had the armament changed to six 20 mm Hispanos mounted in the wingroots. The 324 and 327 used conventional tractor engines while the 325 used pusher engines.^[53]

Griffon engine variants

The early Rolls-Royce Griffon powered Spitfire variants were adaptations of Mk VC (early Mk XII) or Mark VIII (late Mk XII and Mk XVI) airframes. The later Griffon engined Spitfire variants embodied new wings, tail units and undercarriages and were very different from any of the earlier Spitfire marks. Because of this the Griffon engined variants are described in a dedicated article.

Production

After the destruction of the main Itchen and Woolston works by the Luftwaffe in September 1940, all Supermarine manufactured Spitfires were built in a number of "Shadow Factories"; by the end of the war there were ten main factories and several smaller workshops which built many of the components. A fuller explanation can be found in Supermarine Spitfire. The main Castle Bromwich factory was also aided by a smaller number of the shadow factories.^[54]. The breakdown of production figures is taken from Air International 1985, p. 187. Information as to when the first production aircraft emerged is from the serial number lists provided in Morgan and Shacklady 2000. Because the first of the Mk IXs were converted from Mk VCs the first true production Mk IX is listed by serial No.

See also

• British military history of World War II
• Allied technological cooperation during World War II
  

Related development

• Supermarine S.6B
• Seafire
• Spiteful
• Seafang
  

References

Footnotes

• ^a The Coffman starter was connected to the propeller reduction gearbox and used large shotgun-like cartridges loaded into a chamber to "kick-start" the engine. It was first used on the Spitfire Mk II and was also used by Napier Sabre powered aircraft.
• ^b After a series of accidents to Mk Vs in 1942 the A&AEE concluded that the break ups were due to longitudinal-instability, resulting from incorrect loading of the aircraft on the squadrons causing the centre of gravity to be outside the safe limits.
• ^c Some of very early Mk IXs were converted by Rolls-Royce at Hucknall with engine cowlings from Mk Vs extended with a new section welded on to the rear and extemporised blisters added, covering the intercooler which was mounted on the supercharger of the Merlin 61.
• ^d Based on figures taken from a trials report of the prototype taken at the Marine Aircraft Experimental Establishment (MAEE) at Helensburgh (near Glasgow) in 1943.

Citations

Bibliography

Videography

External links

• The Spitfire Site
• The Spitfire Society
• Alan Le Marinel hosts Supermarine Spitfire
• Spitfire Performance Testing
• Spitfire/Seafire Serial Numbers, production contracts and aircraft histories
• Warbird Alley: Spitfire page - Information about Spitfires still flying today
• K5054 - Supermarine Type 300 prototype Spitfire & production aircraft history
• The Spitfire: Seventy Years On - Includes images of the factory
• Spitfire Mk. VIII and Mk. XVI - Temora Aviation Museum page
• National Heritage Warbird Foundation