Hipparcos

Hipparcos

Hipparcos satellite in the Large Solar Simulator, ESTEC, February 1988
General information
NSSDC ID	1989-062B
Organization	European Space Agency
Major contractors	Matra Marconi Space, Alenia Spazio
Launch date	8 August 1989
Launched from	Kourou, French Guiana
Launch vehicle	Ariane 4 (V33)
Mission length	3.5 years Mission end: March 1993
Mass	1140 kg (at launch)
Type of orbit	Geostationary transfer orbit
Orbit height	507 to 35,888 km
Orbit period	10 hours 40 min
Wavelength	Visible light
Diameter	29 cm
Focal length	1.4 m
Website	http://www.rssd.esa.int/hipparcos

Hipparcos (an acronym for High Precision Parallax Collecting Satellite) was a scientific mission of the European Space Agency (ESA), launched in 1989 and operated between 1989 and 1993. It was the first space experiment devoted to astrometry, the accurate measurement of star positions, distances from us, parallaxes, and proper motions. The Hipparcos Catalogue, a high-precision catalogue of more than 100,000 stars, was published in 1997. The lower precision Tycho Catalogue of more than a million stars was published at the same time, while the enhanced Tycho-2 Catalogue of 2.5 million stars was published in 2000.

Background

By the second half of the 20th century, the accurate measurement of star positions from the ground was running into essentially insurmountable barriers to improvements in accuracy, especially for large-angle measurements and systematic terms. Problems were dominated by the effects of the Earth's atmosphere, but were compounded by complex optical terms, thermal and gravitational instrument flexures, and the absence of all-sky visibility. A proposal to make these exacting observations from space was first put forward in 1967.^[1]

Although originally proposed to the French space agency CNES, it was considered too complex and expensive for a single national programme. Its acceptance within the European Space Agency's scientific programme in 1980 was the result of a lengthy process of study and lobby. The underlying scientific motivation was to determine the physical properties of the stars through the measurement of their distances and space motions, and thus to place theoretical studies of stellar structure and evolution, and studies of galactic structure and kinematics, on a more secure empirical basis. Observationally, the objective was to provide the positions, parallaxes, and annual proper motions for some 100,000 stars with an unprecedented accuracy of 0.002 arcseconds, a target in practice eventually surpassed by a factor of two. The name of the space telescope Hipparcos was an acronym for High Precision Parallax Collecting Satellite, and also reflected the name of the Greek astronomer Hipparchus.

Satellite and payload

The spacecraft carried a single all-reflective eccentric Schmidt telescope, with an aperture of 29 cm. A special beam-combining mirror superimposed two fields of view, 58 degrees apart, into the common focal plane. This complex mirror consisted of two mirrors tilted in opposite directions, each occupying half of the rectangular entrance pupil, and providing an unvignetted field of view of about 1°×1°. The telescope used a system of grids, at the focal surface, composed of 2688 alternate opaque and transparent bands, with a period of 1.208 arc-sec (8.2 micrometre). Behind this grid system, an image dissector tube (photomultiplier type detector) with a sensitive field of view of about 38 arc-sec diameter converted the modulated light into a sequence of photon counts (with a sampling frequency of 1200 Hz) from which the phase of the entire pulse train from a star could be derived. The apparent angle between two stars in the combined fields of view, modulo the grid period, was obtained from the phase difference of the two star pulse trains. Originally targeting the observation of some 100,000 stars with an astrometric accuracy of about 0.002 arc-sec, the final Hipparcos Catalogue comprised nearly 120,000 stars with a median accuracy of slightly better than 0.001 arc-sec (1 milliarc-sec).

Optical micrograph of part of the main modulating grid (top) and the star mapper grid (bottom) The period of the main grid is 8.2 micrometre.

An additional photomultiplier system viewed a beam splitter in the optical path and was used as a star mapper – to monitor and determine the satellite attitude, and in the process to gather photometric and astrometric data of all stars down to about 11th magnitude. These measurements were made in two broad bands approximately corresponding to B and V in the (Johnson) UBV photometric system. The positions of these latter stars were to be determined to a precision of 0.03 arcssec, which is a factor of 25 less than the main mission stars. Originally targeting the observation of around 400,000 stars, the resulting Tycho Catalogue comprised just over 1 million stars, with a subsequent analysis extending this to the Tycho-2 Catalogue of about 2.5 million stars.

The attitude of the spacecraft about its center of gravity was controlled to scan the celestial sphere in a regular precessional motion maintaining a constant inclination between the spin axis and the sun direction. The spacecraft spun around its Z-axis at the rate of 11.25 rev/day (168.75 arc-sec/sec) at an angle of 43° to the sun. The Z-axis rotated about the sun-satellite line at 6.4 rev/year.

The spacecraft consisted of two platforms and six vertical panels, all made of aluminum honeycomb. The solar array consisted of three deployable sections, generating around 300W in total. Two S-band antennas were located on the top and bottom of the spacecraft, providing an omni-directional downlink data rate of 24 kbit/s. An attitude and orbit-control subsystem (comprising 5 Newton hydrazine thrusters for course manoeuvres, 20 milli-Newton cold gas thrusters for attitude control, and gyroscopes for attitude determination) ensured correct dynamic attitude control and determination during the operational lifetime.

Principles

Some key features of the observations were as follows:

• through observations from space, the effects of astronomical seeing due to the atmosphere, instrumental gravitational flexure and thermal distortions could be obviated or minimised;
• all-sky visibility permitted a direct linking of the stars observed all over the celestial sphere;
• the two viewing directions of the satellite, separated by a large and suitable angle (58°), resulted in a rigid connection between quasi-instantaneous one-dimensional observations in different parts of the sky. In turn, this led to parallax determinations which are absolute (rather than relative, with respect to some unknown zero-point);
• the continuous ecliptic-based scanning of the satellite resulted in an optimum use of the available observing time, with a resulting catalogue providing reasonably homogeneous sky density and uniform astrometric accuracy over the entire celestial sphere;

Principles of the astrometric measurements. Filled circles and solid lines show three objects from one field of view (about 1° in size), and open circles and dashed lines show three objects from a distinct sky region superimposed by virtue of the large basic angle. Left: object positions at one reference epoch. Middle: their space motions over about four years, with arbitrary proper motion vectors and scale factors; triangles show their positions at a fixed epoch near the end of the interval. Right: the total positional changes including the additional apparent motions due to annual parallax, the four loops corresponding to four Earth orbits around the sun. The parallax-induced motions are in phase for all stars in the same region of sky, so that relative measurements within one field can only provide relative parallaxes. Although the relative separations between the stars change continuously over the measurement period, they are described by just five numerical parameters per star (two components of position, two of proper motion, and the parallax).

• the various geometrical scan configurations for each star, at multiple epochs throughout the 3-year observation programme, resulted in a dense network of one-dimensional positions from which the barycentric coordinate direction, the parallax, and the object's proper motion, could be solved for in what was effectively a global least squares reduction of the totality of observations. The astrometric parameters as well as their standard errors and correlation coefficients were derived in the process;
• since the number of independent geometrical observations per object was large (typically of order 30) compared with the number of unknowns for the standard model (five astrometric unknowns per star) astrometric solutions not complying with this simple five-parameter model, could be expanded to take into account the effects of double or multiple stars, or non-linear photocentric motions ascribed to unresolved astrometric binaries;
• a somewhat larger number of actual observations per object, of order 110, provided accurate and homogeneous photometric information for each star, from which mean magnitudes, variability amplitudes, and in many cases period and variability type classification could be undertaken.

The path on the sky of one of the Hipparcos Catalogue objects, over a period of three years. Each straight line indicates the observed position of the star at a particular epoch: because the measurement is one-dimensional, the precise location along this position line is undetermined by the observation. The curve is the modelled stellar path fitted to all the measurements. The inferred position at each epoch is indicated by a dot, and the residual by a short line joining the dot to the corresponding position line. The amplitude of the oscillatory motion gives the star's parallax, with the linear component representing the star's proper motion.

Development, launch and operations

The Hipparcos satellite was financed and managed under the overall authority of the European Space Agency. The main industrial contractors were Matra Marconi Space (now EADS Astrium) and Alenia Spazio (now Thales Alenia Space).

Other hardware components were supplied as follows: the beam-combining mirror from REOSC at Saint Pierre du Perray; the spherical, folding and relay mirrors from Carl Zeiss AG in Oberkochen; the external straylight baffles from CASA in Madrid; the modulating grid from CSEM in Neuchatel; the mechanism control system and the thermal control electronics from Dornier Satellite Systems in Friedrichshafen; optical filters, the experiment structures and the attitude and orbit control system from Matra Marconi Space in Velizy; instrument switching mechanisms from Oerlikon-Contraves in Zurich; the image dissector tube and photomultiplier detectors assembled by the Dutch Space Research Organisation, SRON in The Netherlands; the refocusing assembly mechanism designed by TNO-TPD in Delft; the electrical power subsystem from British Aerospace in Bristol; the structure and reaction control system from Daimler-Benz Aerospace in Bremen; the solar arrays and thermal control system from Fokker Space System in Leiden; the data handling and telecommunications system from Saab-Ericsson Space in Gotenborg; and the apogee boost motor from SEP in France. Groups from the Institut d'Astrophysique in Liege and the Laboratoire d'Astronomie Spatiale in Marseille contributed optical performance, calibration and alignment test procedures; Captec in Dublin and Logica in London contributed to the on-board software and calibration.

The Hipparcos satellite was launched (with the direct broadcast satellite TV-SAT2 as co-passenger) on an Ariane 4 launch vehicle, flight V33, from Kourou, French Guiana, on 8 August 1989. Launched into a geostationary transfer orbit, the Mage-2 apogee boost motor failed to fire, and the intended geostationary orbit was never achieved. However, with the addition of further ground stations, in addition to the primary ground station at Odenwald in Germany, the satellite was successfully operated in its geostationary transfer orbit for almost 3.5 years. All of the original mission goals were, eventually, exceeded.

The satellite was operated by the ESA operations control centre at ESOC, Darmstadt (Germany).

Including an estimate for the scientific activities related to the satellite observations and data processing, Hipparcos mission cost some 600 MEuro (2000 economic conditions), and its execution involved some 200 European scientists and more than 2000 individuals in European industry.

Hipparcos Input Catalogue

The satellite observations relied on a pre-defined list of target stars. Stars were observed as the satellite rotated, by a sensitive region of the image dissector tube detector. This pre-defined star list formed the Hipparcos Input Catalogue: each star in the final Hipparcos Catalogue was contained in the Input Catalogue^[2]. The Input Catalogue was compiled by the INCA Consortium over the period 1982—89, finalised pre-launch, and published both digitally and in printed form ^[3]. Although fully superseded by the satellite results, it nevertheless includes supplemental information on multiple system components as well as compilations of radial velocities and spectral types which, not observed by the satellite, were not included in the published Hipparcos Catalogue.

Constraints on total observing time, and on the uniformity of stars across the celestial sphere for satellite operations and data analysis, led to an Input Catalogue of some 118,000 stars. It merged two components: first, a survey of around 58,000 objects as complete as possible to the following limiting magnitudes: V<7.9 + 1.1sin|b| for spectral types earlier than G5, and V<7.3 + 1.1sin|b| for spectral types later than G5 (b is the Galactic latitude). Stars constituting this survey are flagged in the Hipparcos Catalogue.

The second component comprised additional stars selected according to their scientific interest, with none fainter than about magnitude V=13 mag. These were selected from around 200 scientific proposals submitted on the basis of an Invitation for Proposals issued by ESA in 1982, and prioritised by the Scientific Proposal Selection Committee in consultation with the Input Catalogue Consortium. This selection had to balance 'a priori' scientific interest, and the observing programme's limiting magnitude, total observing time, and sky uniformity constraints.

Data reductions

For the main mission results, the data analysis was carried out by two independent scientific teams, NDAC and FAST, together comprising some 100 astronomers and scientists, mostly from European (ESA-member state) institutes. The analyses, proceeding from nearly 1000 Gbit of satellite data acquired over 3.5 years, incorporated a comprehensive system of cross-checking and validation, and is described in detail in the published catalogue.

A detailed optical calibration model was included to map the transformation from sky to instrumental coordinates. Its adequacy could be verified by the detailed measurement residuals. The Earth's orbit, and the satellite's orbit with respect to the Earth, were essential for describing the location of the observer at each epoch of observation, and were supplied by an appropriate Earth ephemeris combined with accurate satellite ranging. Corrections due to special relativity (stellar aberration) made use of the corresponding satellite velocity. Modifications due to General Relativistic light bending were significant (4 milliarc-sec at 90° to the ecliptic) and corrected for deterministically assuming γ=1 in the PPN formalism. Residuals were examined to establish limits on any deviations from this General Relativistic value, and no significant discrepancies were found.

The Hipparcos reference frame

The satellite observations essentially yielded highly accurate relative positions of stars with respect to each other, throughout the measurement period (1989–93). In the absence of direct observations of extragalactic sources (apart from marginal observations of 3C 273) the resulting rigid reference frame was transformed to an inertial frame of reference linked to extragalactic sources. This allows surveys at different wavelengths to be directly correlated with the Hipparcos stars, and ensures that the catalogue proper motions are, as far as possible, kinematically non-rotating. The determination of the relevant three solid-body rotation angles, and the three time-dependent rotation rates, was conducted and completed in advance of the catalogue publication. This resulted in an accurate but indirect link to an inertial, extragalactic, reference frame^[4].

Typical accuracies of the FK5, Hipparcos, Tycho-1, and Tycho-2 Catalogues as a function of time. Tycho-1 dependencies are shown for two representative magnitudes. For Tycho-2, a typical proper motion error of 2.5 milliarc-sec applies to both bright stars (positional error at J1991.25 of 7 milliarc-sec) and faint stars (positional error at J1991.25 of 60 milliarc-sec).

A variety of methods to establish this reference frame link before catalogue publication were included and appropriately weighted: interferometric observations of radio stars by VLBI networks, MERLIN and VLA; observations of quasars relative to Hipparcos stars using CCDs, photographic plates, and the Hubble Space Telescope; photographic programmes to determine stellar proper motions with respect to extragalactic objects (Bonn, Kiev, Lick, Potsdam, Yale/San Juan); and comparison of Earth rotation parameters obtained by VLBI and by ground-based optical observations of Hipparcos stars. Although very different in terms of instruments, observational methods and objects involved, the various techniques generally agreed to within 10 milliarc-sec in the orientation and 1 milliarc-sec/yr in the rotation of the system. From appropriate weighting, the coordinate axes defined by the published catalogue are believed to be aligned with the extragalactic radio frame to within ±0.6 milliarc-sec at the epoch J1991.25, and non-rotating with respect to distant extragalactic objects to within ±0.25 milliarc-sec/yr.

The Hipparcos and Tycho Catalogues were then constructed such that the Hipparcos reference frame coincides, to within observational uncertainties, with the International Celestial Reference System (the ICRS), and representing the best estimates at the time of the catalogue completion (in 1996). The resulting Hipparcos reference frame is thus the materialisation of the ICRS in the optical. It extends and improves the J2000(FK5) system, retaining approximately the global orientation of that system but without its regional errors.

Double and multiple stars

Whilst of enormous astronomical importance, double stars and multiple stars provided considerable complications to the observations (due to the finite size and profile of the detector's sensitive field of view) and to the data analysis. The data processing classified the astrometric solutions as follows:

• single star solutions: 100,038 entries, of which 6,763 were flagged as suspected double
• component solutions (Annex C): 13,211 entries, comprising 24,588 components in 12,195 solutions
• acceleration solutions (Annex G): 2,622 solutions
• orbital solutions (Annex O): 235 entries
• variability-induced movers (Annex V): 288 entries
• stochastic solutions (Annex X): 1,561 entries
• no valid astrometric solution: 263 entries (of which 218 were flagged as suspected double)

If a binary star has a long orbital period such that non-linear motions of the photocentre were insignificant over the short (3-year) measurement duration, the binary nature of the star would pass unrecognised by Hipparcos, but could show as a Hipparcos proper motion discrepant compared to those established from long temporal baseline proper motion programmes on ground. Higher-order photocentric motions could be represented by a 7-parameter, or even 9-parameter model fit (compared to the standard 5-parameter model), and typically such models could be enhanced in complexity until suitable fits were obtained. A complete orbit, requiring 7 elements, was determined for 45 systems. Orbital periods close to one year can become degenerate with the parallax, resulting in unreliable solutions for both. Triple or higher-order systems provided further challenges to the data processing.

Photometric observations

The highest accuracy photometric data were provided as a by-product of the main mission astrometric observations. They were made in a broad-band visible light passband, specific to Hipparcos, and designated Hp. The median photometric precision, for Hp<9 mag, was 0.0015 mag, with typically 110 distinct observations per star throughout the 3.5-year observation period. As part of the data reductions and catalogue production, new variables were identified and designated with appropriate variable star identifiers. Variable stars were classified as periodic or unsolved variables; the former were published with estimates of their period, variability amplitude, and variability type. In total some 11,597 variable objects were detected, of which 8237 were newly-classified as variable. There are, for example, 273 Cepheid variables, 186 RR Lyr variables, 108 Delta Scuti variables, and 917 eclipsing binary stars. The star mapper observations, constituting the Tycho (and Tycho-2) Catalogue, provided two colours, roughly B and V in the Johnson UBV photometric system, important for spectral classification and effective temperature determination.

Radial velocities

Classical astrometry concerns only motions in the plane of the sky and ignores the star's radial velocity, i.e. its space motion along the line-of-sight. Whilst critical for an understanding of stellar kinematics, and hence population dynamics, its effect is generally imperceptible to astrometric measurements (in the plane of the sky), and therefore it is generally ignored in large-scale astrometric surveys. In practice, it can be measured as a Doppler shift of the spectral lines. More strictly, however, the radial velocity does enter a rigorous astrometric formulation. Specifically, a space velocity along the line-of-sight means that the transformation from tangential linear velocity to (angular) proper motion is a function of time. The resulting effect of secular or perspective acceleration is the interpretation of a transverse acceleration actually arising from a purely linear space velocity with a significant radial component, with the positional effect proportional to the product of the parallax, the proper motion, and the radial velocity. At the accuracy levels of Hipparcos it is of (marginal) importance only for the nearest stars with the largest radial velocities and proper motions, but was accounted for in the 21 cases for which the accumulated positional effect over two years exceeds 0.1 milliarc-sec. Radial velocities for Hipparcos Catalogue stars, to the extant that they are presently known from independent ground-based surveys, can be found from the astronomical data base of the Centre de Données astronomiques de Strasbourg.

The absence of reliable distances for the majority of stars means that the angular measurements made, astrometrically, in the plane of the sky, cannot generally be converted into true space velocities in the plan of the sky. For this reason, astrometry characterises the transverse motions of stars in angular measure (e.g. arcsec per year) rather than in km/sec or equivalent. Similarly, the typical absence of reliable radial velocities means that the transverse space motion (when known) is, in any case, only a component of the complete, three-dimensional, space velocity.

Published catalogues

The final Hipparcos Catalogue was the result of the critical comparison and merging of the two (NDAC and FAST consortia) analyses, and contains 118,218 entries (stars or multiple stars), corresponding to an average of some three stars per square degree over the entire sky^[5]. Median precision of the five astrometric parameters (Hp<9 mag) exceeded the original mission goals, and are between 0.6–1.0 mas. Some 20,000 distances were determined to better than 10%, and 50,000 to better than 20%. The inferred ratio of external to standard errors is ≈1.0–1.2, and estimated systematic errors are below 0.1 mas. The number of solved or suspected double or multiple stars is 23,882^[6]. Photometric observations yielded multi-epoch photometry with a mean number of 110 observations per star, and a median photometric precision (Hp<9 mag) of 0.0015 mag, with 11,597 entries were identified as variable or possibly variable^[7].

For the star mapper results, the data analysis was carried out by the TDAC consortium. The Tycho Catalogue comprises more than one million stars with 20–30 milliarc-sec astrometry and two-colour (B and V band) photometry^[8].

The final Hipparcos and Tycho Catalogues were completed in August 1996. The catalogues were published by ESA on behalf of the scientific teams in June 1997^[9].

A more extensive analysis of the star mapper (Tycho) data extracted additional faint stars from the data stream. Combined with old photographic plate observations made several decades earlier as part of the Astrographic Catalogue programme, the Tycho-2 Catalogue of more than 2.5 million stars (and fully superseding the original Tycho Catalogue) was published in 2000^[10].

The Hipparcos and Tycho-1 Catalogues were used to create the Millennium Star Atlas: an all-sky atlas of one million stars to visual magnitude 11. Some 10,000 nonstellar objects are also included to complement the catalogue data^[11].

Between 1997 and 2007, investigations into subtle effects in the satellite attitude and instrument calibration continued. A number of effects in the data that had not been fully accounted for were studied, such as scan-phase discontinuities and micrometeoroid-induced attitude jumps. A re-reduction of the associated steps of the analysis was eventually undertaken^[12]. This has led to improved astrometric accuracies for stars brighter than Hp=9.0 mag, reaching a factor of about three for the brightest stars (Hp<4.5 mag), while also underlining the conclusion that the Hipparcos Catalogue as originally published is generally reliable within the quoted accuracies.

All catalogue data are available online from the Centre de Données astronomiques de Strasbourg.

Scientific results

The Hipparcos results impact a very broad range of astronomical research, which can be classified into three major themes:

(a) the provision of an accurate reference frame: this has allowed the consistent and rigorous re-reduction of historical astrometric measurements, including those from Schmidt plates, meridian circles, the 100-year old Astrographic Catalogue, and 150 years of Earth-orientation measurements. These, in turn, have yielded a dense reference framework with high-accuracy long-term proper motions (the Tycho-2 Catalogue). Reduction of current state-of-the-art survey data has yielded the dense UCAC2 Catalogue of the US Naval Observatory on the same reference system, and improved astrometric data from recent surveys such as the Sloan Digital Sky Survey and 2MASS. Implicit in the high-accuracy reference frame is the measurement of General Relativistic light bending, and the detection and characterisation of double and multiple stars;

(b) constraints on stellar structure and stellar evolution: the accurate distances and luminosities of 100,000 stars has provided the most comprehensive and accurate data set of fundamental stellar parameters to date, placing constraints on internal rotation, element diffusion, convective motions, and asteroseismology. Combined with theoretical models and other data it yields evolutionary masses, radii, and ages for large numbers of stars covering a wide range of evolutionary states;

Artists concept of our Milky Way galaxy, showing two prominent spiral arms attached to the ends of a thick central bar. Hipparcos has mapped our solar precinct in great detail.

(c) Galactic kinematics and dynamics: the uniform and accurate distances and proper motions have provided a substantial advance in understanding of stellar kinematics and the dynamical structure of the solar neighbourhood, ranging from the presence and evolution of clusters, associations and moving groups, the presence of resonance motions due to the Galaxy's central bar and spiral arms, determination of the parameters describing Galactic rotation, discrimination of the disk and halo populations, evidence for halo accretion, and the measurement of space motions of runaway stars, globular clusters, and many other types of star.

Associated with these major themes, Hipparcos has provided results in topics as diverse as Solar System science, including mass determinations of asteroids, Earth's rotation and Chandler Wobble, the internal structure of white dwarfs, the masses of brown dwarfs, the characterisation of extra-solar planets and their host stars, the height of the Sun above the Galactic mid-plane, the age of the Universe, the stellar initial mass function and star formation rates, and strategies for the search for extraterrestrial intelligence. The high-precision multi-epoch photometry has been used to measure variability and stellar pulsations in many classes of objects. The Hipparcos and Tycho Catalogues are now routinely used to point ground-based telescopes, navigate space missions, and drive public planetaria.

Since 1997, several thousand scientific papers have been published making use of the Hipparcos and Tycho Catalogues. A detailed review of the Hipparcos scientific literature between 1997–2007 was published in 2009^[13]. Some examples of notable results include (listed chronologically):

• studies of Galactic rotation from Cepheid variables^[14]
• the nature of Delta Scuti variables^[15]
• studies of local stellar kinematics^[16]
• testing the white dwarf mass-radius relation^[17]
• the structure and dynamics of the Hyades cluster^[18]
• kinematics of Wolf-Rayet stars and O-type runaway stars^[19]
• subdwarf parallaxes: metal-rich clusters and the thick disk^[20]
• fine structure of the red giant clump and associated distance determinations^[21]
• unexpected stellar velocity distribution in the warped Galactic disk^[22]
• refining the Oort and Galactic constants^[23]
• Galactic disk dark matter, terrestrial impact cratering and the law of large numbers^[24]
• vertical motion and expansion of the Gould Belt^[25]
• the use of gamma ray bursts as direction and time markers in SETI strategies^[26]
• evidence of a galaxy merger in the early formation history of the Milky Way^[27]
• study of nearby OB associations^[28]
• close approaches of stars to the Solar System^[29]
• studies of binary star orbits and masses^[30]
• the HD 209458 planetary transits^[31]
• formation of the stellar Galactic halo and thick disk^[32]
• the local density of matter in the Galaxy and the Oort limit^[33]
• ice age epochs and the Sun's path through the Galaxy^[34]
• local kinematics of K and M giants and the concept of superclusters^[35]
• an improved reference frame for long-term Earth rotation studies^[36]
• the local stellar velocity field in the Galaxy^[37]

One controversial result has been the derived proximity, at about 120 parsecs, of the Pleiades cluster, established both from the original catalogue^[38] as well as from the revised analysis^[12]. This has been contested by various other recent work, placing the mean cluster distance at around 130 parsecs.^{[39][40][41][42]}

People

• Pierre Lacroute (Observatory of Strasbourg): proposer of space astrometry in 1967
• Michael Perryman: ESA project scientist
• Catherine Turon (Observatoire de Paris-Meudon): leader of Input Catalogue Consortium
• Erik Høg: leader of the TDAC Consortium
• Lennart Lindegren: leader of the NDAC Consortium
• Jean Kovalevsky: leader of the FAST Consortium
• Adriaan Blaauw: chair of the observing programme selection committee
• Hipparcos Science Team: Uli Bastian, Pierluigi Bernacca, Michel Crézé, Francesco Donati, Michel Grenon, Michael Grewing, Erik Høg, Jean Kovalevsky, Floor van Leeuwen, Lennart Lindegren, Hans van der Marel, Francois Mignard, Andrew Murray, Michael Perryman (chair), Rudolf Le Poole, Hans Schrijver, Catherine Turon
• Franco Emiliani: ESA project manager (1981–85)
• Hamid Hassan: ESA project manager (1985–89)
• Dietmar Heger: ESA/ESOC spacecraft operations manager
• Michel Bouffard: Matra Marconi Space project manager
• Bruno Strim: Alenia Spazio project manager

See also

• Gaia mission
• Space Interferometry Mission
• Full-Sky Astrometric Mapping Explorer

References

External links

• ESA website The Hipparcos Space Astrometry Mission
• Hipparcos and Tycho Catalogues from the CDS Data Base The Hipparcos and Tycho Catalogues