Loom
A loom is a machine or device for weaving thread or yarn into textiles. Looms can range from very small hand-held frames, to large free-standing hand looms, to huge automatic mechanical devices.
In practice, the basic purpose of any loom is to hold the warp threads under tension to facilitate the interweaving of the weft threads. The precise shape of the loom and its mechanics may vary, but the basic function is the same.
Contents |
Weaving
- See Weaving for more information.
- See Textile manufacturing terminology for more terms connected with looms.
Weaving is done by intersecting the longitudinal threads, the warp, i.e. "that which is thrown across", with the transverse threads, the woof or weft, i.e. "that which is woven".
The earliest attestation of loom with its specific meaning quoted by the Oxford English Dictionary is from the Nottingham Records of 1404, but handwoven cloth existed much earlier, perhaps as far back as 8000 BC.
Types of looms
Handloom
The earliest looms were vertical warp-weighted looms, with the warp threads suspended from a branch or piece of wood and weighted or attached to the ground. The weft threads would be pushed into place by hand or a stick that would eventually become the shuttle. At first, it was necessary to raise and lower every warp thread one at a time, which was a time-consuming and laborious process. Basic techniques, such as the insertion of a rod, were developed to produce a shed, the space between warp threads (perhaps every other thread would be alternately raised and lowered), so that the weft thread or shuttle could pass through the entire warp at once.
Ground looms
On a horizontal ground loom, the warp would be strung between two rows of pegs. The weaver would have to lean over in order to work, so pit looms were developed, with the warp strung over a pit, so the weaver could sit with his or her legs underneath and would then be on a level with the loom.
Frame looms
Frame looms followed basically the same principles as ground looms. The loom was constructed out of sticks and boards attached at right angles (producing a box-like shape), which meant that it was portable and could even be held in the weaver's lap. Frame looms are still in use today, usually as a portable, less expensive, and compact alternative to a table or floor loom. Also known as a small loom.
Back strap looms
Backstrap looms, as the name implies, are tied around the weaver's waist on one end and around a stationary object such as a tree, post, or door on the other. Tension can be adjusted simply by leaning back. Backstrap looms are very portable, since they can simply be rolled up and carried.
Foot-treadle floor looms
Handweavers today tend to use looms with at least four shafts or harnesses. Each shaft contains a set of heddles through which yarn can be threaded (and attached, through a variety of mechanisms, to the front and back beams of the loom), and by raising the harnesses in different combinations, a variety of patterns can be achieved. Looms with two such shafts are used for weaving tabby or even weave fabrics. Multishaft looms with eight, twelve, sixteen or more shafts are available.
The shafts on a floor loom are controlled by a series of pedals called treadles. This is an important development, since it keeps the weaver's hands free to manipulate the shuttle and it is easy to raise and lower warp threads in selected combinations. As the fabric is woven it is rolled around the cloth beam, as unwoven warp or yarn is unrolled from the warp beam, so the length of the weaving is not limited by the size of the loom. A table loom is similar, but, as the name suggests, it is smaller and equipped with hand levers rather than treadles, since it is made to sit on a stand or on top of a table.
A computer assisted loom has no actual treadles as the computer program dictates which harness or shaft is lifted, either by a manual pedal or air cylinders, hydraulic cylinders or electric solenoids. A loom that can only lift the shafts is called a rising shed loom or a Jack loom. A loom that can sink and lift the shafts at the same time is called a sinking shed loom, and is constructed in either of two forms: counterbalance loom or countermarch loom. Most counterbalance looms use four harnesses, whereas countermarch looms use many (up to about thirty-two) harnesses.
A harness is a complete set of loom parts; a lamm, a shaft and an upper harness of cords or jacks. A shaft is a frame which holds a set of heddles which guide some of the warp but not all on one shaft, there is always more than one shaft on a loom.
Rigid heddle looms
Rigid heddle looms cross multiple types of looms, including frame looms and backstrap looms. In rigid heddle looms there is typically a single shaft, with the heddles fixed in place in the shaft. The warp threads pass alternately through a heddle and through a space between the heddles, so that raising the shaft will raise half the threads (those passing through the heddles), and lowering the shaft will lower the same threads -- the threads passing through the spaces between the heddles remain in place.
Haute lisse and basse lisse looms
Looms used for weaving traditional tapestry are classified as haute lisse looms, where the warp is suspended vertically between two rolls, and the basse lisse looms, where the warp extends horizontally between the rolls.
Power looms
The first completely automated loom was made by Jacques Vaucanson in 1745. A different power loom was built by Edmund Cartwright in 1785. Originally, powered looms were shuttle-operated but in the early part of the 20th century the faster and more efficient shuttleless loom came into use. Today, advances in technology have produced a variety of looms designed to maximize production for specific types of material. The most common of these are air-jet looms and water-jet looms. Computer-driven looms are now also available to individual (non-industrial) weavers.
Industrial looms can weave at speeds of six rows per second and faster.
Knitting looms
Knitting looms (also known as Amish looms or knitting boards) were recently popularized in crafting circles by the Knifty Knitter system. Knitting looms are a descendant of the frame loom. Grooved pegs are spaced along a central frame. These pegs are wrapped with yarn in various ways, then the knitter uses an angled hook to pull the wrapped yarn over the top of the peg, resulting in a fabric with stitches similar to a needle knitted item.
Bow Looms
A type of loom used for thin strips of beading. A bow loom consists of a bendable branch of cedar, willow or other easily bendable types of wood. 10-11 holes are then made along the length of two smaller pieces of wood. Thread is looped through the holes and attached to the long bendable piece. Once the bow is threaded, the thread is then used for beading. This method was traditionally used by the Native Americans.
Shuttle Looms
The major components of the loom are the warp beam, heddles, harnesses, shuttle, reed and takeup roll. In the loom, yarn processing includes shedding, picking, battening and taking-up operations.
Shedding. Shedding is the raising of the warp yarns to form a shed through which the filling yarn, carried by the shuttle, can be inserted. The shed is the vertical space between the raised and unraised warp yarns. On the modern loom, simple and intricate shedding operations are performed automatically by the heddle frame, also known as a harness. This is a rectangular frame to which a series of wires, called heddles, are attached. The yarns are passed through the eye holes of the heddles, which hang vertically from the harnesses. The weave pattern determines which harness controls which warp yarns, and the number of harnesses used depends on the complexity of the weave.
Picking. As the harnesses raise the heddles, which raise the warp yarns, the shed is created. The filling yarn in inserted through the shed by a small carrier device called a shuttle. The shuttle is normally pointed at each end to allow passage through the shed. In a traditional shuttle loom, the filling yarn is wound onto a quill, which in turn is mounted in the shuttle. The filling yarn emerges through a hole in the shuttle as it moves across the loom. A single crossing of the shuttle from one side of the loom to the other is known as a pick. As the shuttle moves back and forth across the shed, it weaves an edge, or selvage, on each side of the fabric to prevent the fabric from raveling.
Battening. As the shuttle moves across the loom laying down the fill yarn, it also passes through openings in another frame called a reed (which resembles a comb). With each picking operation, the reed presses or battens each filling yarn against the portion of the fabric that has already been formed. Conventional shuttle looms can operate at speeds of about 150 to 160 picks per minute.
With each weaving operation, the newly constructed fabric must be wound on a cloth beam. This process is called taking up. At the same time, the warp yarns must be let off or released from the warp beams (Corbman, 1975).
Patents
- U.S. Patent 0,000,169 -- Loom
See also
- Timeline of clothing and textiles technology
- Weaving (mythology)
- Shuttle (weaving)
External links
- Loom demonstration video
- "Loom Knitting Help" article
- "Caring for your loom" article
- "Learn to Use a Knitting Loom"
- "The Art and History of Weaving"
- "Shuttle looms for narrow fabrics"
|
|||||||||||||||||||
