Train event recorder

From Wikipedia, the free encyclopedia

Train event recorders are similar to flight data recorders found on aircraft. They record data about the operation of train controls and performance in response to those controls and other train control systems.

Data storage is provided by magnetic tape, battery-backed RAM and, most recently, nonvolatile EEPROM or Flash Memory overwritten in a FIFO continuous loop.The data is mainly used in the investigation of accidents and incidents but can also be used to monitor traction unit performance and the competence of drivers.

Contents

[edit] Definitions

In English speaking countries the term event recorder is used in documents requiring their use and defining specifications.

In the United States: From CFR 49 Ch II 229.5 Definitions. (g) Event recorder means a device, designed to resist tampering, that monitors and records data on train speed, direction of motion, time, distance, throttle position, brake applications and operations (including train brake, independent brake, and, if so equipped, dynamic brake applications and operations) and, where the locomotive is so equipped, cab signal aspect(s), over the most recent 48 hours of operation of the electrical system of the locomotive on which it is installed. A device, designed to resist tampering, that monitors and records the specified data.[1]

In Canadian Regulations: Locomotives Design Requirements (Part II) 12. Event Recorders 12.1 Controlling locomotives other than in designated and/or yard service, shall be equipped with an event recorder meeting the following minimum design criteria: The event recorder shall record the time, the distance, the speed, the brake pipe pressure, the throttle position, the emergency brake application, the independent brake cylinder pressure, the horn signal and Reset Safety Control function. [2]

In the UK the term on-train monitoring recorder‎ (OTMR) is also used in GM/RT 2472 "Design Requirements for Event Recorders on Trains.”

[edit] History

The earliest event recorders were the mechanical TEL (abbreviation of "Telegraphenwerkstätte von G.Hasler")[3] speed recorders of 1891, which recorded both time and speed.

[edit] Regulations

[edit] United States

The Federal Railroad Administrations (FRA) "Final Rule 49 CFR Part 229", (revised June 30, 2005) [4][5] requires that Event recorders be fitted to the leading locomotives of all US, Canadian & Mexican trains operating above 30 MPH on the US rail network including all freight, passenger and commuter rail locomotives but does not apply to transit running on its own dedicated tracks.

The new ruling applies to locomotives either ordered before Oct 1, 2006 or placed in service after Oct 1, 2009 and included:

  • Improved crash worthiness by means of a “hardened” memory module able to withstand:
    • Fire resistance of 750 C for 1 hour this test simulates the temperature of burning diesel fuel
    • Impact shock of 55 g
    • Static crush of 110kN for 5 minutes this test simulates a locomotive derailment and blunt object impact
    • Fluid immersion in Diesel, water, salt water or lube oils for 2-days
    • Hydrostatic pressure equivalent to immersion to a depth of 15 m in water for 2-days
  • Recording of additional information to enhance the quality of information available for post-accident investigations including the following “safety-critical” signals:
    • Speed
    • Direction of travel (Forward or Reverse)
    • Time
    • Distance
    • Throttle position
    • Operation of brakes
    • Status of Headlights & Marker Lights (On or Off)
    • Operation of Horn
    • Status of Cab signals
  • Store the last 48 hours of safety-critical train data. This is to prevent over-writing of the crash data if the loco is used for the subsequent "clean-up" of the crash scene.
  • The phasing out of the old magnetic tape models over a four year period due to their vulnerability to data loss in the event of a crash.

[edit] United Kingdom and Ireland

All trains operating on Network Rail controlled infrastructure are required to be fitted with an Event recorder complying with GM/RT 2472.[6] Ireland has also adopted this regulation.

Crash protection requirements:

  • Fire resistance of 700 C for 5-minutes
  • Impact shock of 100 g, 3 times on each of its 6 sides
  • Static crush of 20kN for 1-minute, to all edges and faces
  • Fluid immersion in water, AFFF or R134A for 1-hour
  • Magnetic field produced by a current of 0 to 64kA, rising at 107 A/sec at a distance of 1-meter

The UK approach is similar to US requirements, but the list of required signals is more comprehensive. This reflects, in part, the prevalence of passenger trains and the inevitable possibility of incidents involving access doors.

Signals to be recorded include:

  • Brake demand including operation of all Brake Controls & other brake activations
  • Power notch
  • Wheel speed
  • Speedometer, both signal sent to speedometer and indication displayed to driver
  • AWS operation
  • DRA operation
  • Vigilance Operation
  • PES - Passenger Emergency Systems,
  • Override of any Safety System
  • Horn
  • Door signals
  • Door inter-lock
  • WSP
  • Tilt, if fitted
  • Speed supervision & Control, if fitted

[edit] Switzerland

Speed recording equipment has been used by Swiss Federal Railways for many years.

[edit] See also

[edit] References

  1. ^ Code of Federal Regulations - Sec. 229.5 Definitions
  2. ^ Locomotives Design Requirements (Part II) - Event Recorders
  3. ^ HaslerRail history
  4. ^ FRA ruling
  5. ^ FRA press release
  6. ^ GM/RT 2472, Data Recorders Design - Requirements