Rocket engine

From Wikipedia, the free encyclopedia

RS-68 being tested at NASA's Stennis Space Center. The nearly transparent exhaust is due to this engine's exhaust being mostly superheated steam (water vapor from its propellants, hydrogen and oxygen)

A rocket engine is a jet engine^[1] that takes all its reaction mass ("propellant") from within tankage or the body of a vehicle and forms it into a high speed jet, thereby obtaining thrust in accordance with Newton's third law. Rocket engines can be used for spacecraft propulsion as well as terrestrial uses, such as missiles. Most rocket engines are internal combustion engines, although non combusting forms also exist.

[edit] Principle of operation

Rocket engines give part of their thrust due to unopposed pressure on the combustion chamber

Most rocket engines produce thrust by the expulsion of a high-temperature, high-speed gaseous exhaust. This is typically created by high pressure (10-200 bar) combustion of solid or liquid propellants, consisting of fuel and oxidiser components, within a combustion chamber.

[edit] Introducing propellant into the combustion chamber

Liquid-fueled rockets typically pump separate fuel and oxidiser components into the combustion chamber, where they mix and burn. Solid rocket propellants are prepared as a mixture of fuel and oxidizing components and the propellant storage chamber becomes the combustion chamber. Hybrid rocket engines use a combination of solid and liquid or gaseous propellants. Alternatively, a chemically inert reaction mass can be heated using a high-energy power source.

[edit] Combustion chamber

For chemical rockets the combustion chamber is typically just a cylinder. The dimensions of the cylinder is such that the propellant is able to combust thoroughly; different propellants require different combustion chamber sizes for this to occur. This leads to a number called $L *$ :

$L* = \frac {V_c} {A_t}$

where:

V c

is the Volume of the chamber

A t

is the area of the throat

L* is typically in the range of 25-60 inches (0.6 - 1.5 m)

[edit] Rocket nozzles

Main article: Rocket engine nozzle

The hot gas produced is permitted to escape from the combustion chamber through an opening (the "throat"), in a high expansion-ratio 'de Laval nozzle'. The nozzle dramatically accelerates the gas, converting most of the thermal energy into kinetic energy. The large bell or cone shaped expansion nozzle gives a rocket engine its characteristic shape. Exhaust speeds as high as ten times the speed of sound at sea level are not uncommon.

Rocket thrust is caused by pressures acting in the combustion chamber and nozzle. From Newtons third law, equal and opposite pressures act on the exhaust, and this accelerates it to high speeds.

A portion of the rocket engine's thrust comes from the unbalanced pressures inside the combustion chamber but the majority comes from the pressures against the inside of the nozzle (see diagram). As the gas expands (adiabatically) the pressure against the nozzle's walls forces the rocket engine in one direction while accelerating the gas in the other.

[edit] Propellant efficiency

For a rocket engine to be propellant efficient, it is important that the maximum pressures possible be created by a specific amount of propellant acting on the chamber and nozzle. This can be achieved by all of:

heating the propellant to as high a temperature as possible (using a high energy fuel, containing hydrogen and carbon and sometimes metals such as aluminium, or even using nuclear energy)
using a low specific density gas (as hydrogen rich as possible)
using propellants which are, or decompose to, simple molecules with few degrees of freedom so as to maximise molecular speeds

Since all of these things minimise the mass of the propellant used, and since pressure is proportional to the amount of propellant present to be accelerated as it pushes on the engine, and since from Newton's third law the pressure that acts on the engine also reciprocally acts on the propellant, it turns out that the speed that the propellant leaves the chamber is unaffected by the chamber pressure (although the thrust is proportional). However, speed is significantly affected by all three of the above factors and the exhaust speed is an excellent measure of the engine propellant efficiency.

For aerodynamic reasons the flow goes sonic ("chokes") at the narrowest part of the nozzle, the 'throat'. Since the speed of sound in gases increases with the square root of temperature, the use of hot exhaust gas greatly improves performance. By comparison, at room temperature the speed of sound in air is about 340m/s while the speed of sound in the hot gas of a rocket engine can be over 1700m/s; much of this performance is due to the higher temperature, but additionally rocket propellants are chosen to be of low molecular mass, and this also gives a higher velocity compared to air.

Expansion in the rocket nozzle then further multiplies the speed, typically between 1.5 and 2 times, giving a highly collimated hypersonic exhaust jet. The speed increase of a rocket nozzle is mostly determined by its area expansion ratio—the ratio of the area of the throat to the area at the exit, but detailed properties of the gas are also important. Larger ratio nozzles are more massive but are able to extract more heat from the combustion gases, increasing the exhaust velocity.

Nozzle efficiency is affected by operation in the atmosphere because atmospheric pressure changes with altitude; but due to the supersonic speeds of the gas exiting from a rocket engine, the pressure of the jet may be either below or above ambient, and equilibrium between the two is not reached.

[edit] Back pressure and optimal expansion

For optimal performance the pressure of the gas at the end of the nozzle should just equal the ambient pressure; if lower the vehicle will be slowed by the difference in pressure between the top of the engine and the exit, if higher then this represents pressure that the bell has not turned into thrust.

To maintain this ideal the diameter of the nozzle would need to increase with altitude, giving the pressure a longer nozzle to act on (and reducing the exit pressure and temperature). This increase is difficult to arrange. A compromise nozzle is generally used and some reduction in performance occurs. To improve on this, various exotic nozzle designs such as the plug nozzle, stepped nozzles, the expanding nozzle and the aerospike have been proposed, each having some way to adapt to changing ambient air pressure and each allowing the gas to expand further against the nozzle, giving extra thrust at higher altitude.

[edit] Overall rocket engine performance

Rocket technology can combine very high thrust (meganewtons), very high exhaust speeds (around 10 times the speed of sound at sea level) and very high thrust/weight ratios (>100) simultaneously as well as being able to operate outside the atmosphere.

Rockets can be further optimised to even more extreme performance along one or more of these axes at the expense of the others.

[edit] Specific impulse

Main article: Specific impulse

The most important metric for the efficiency of a rocket engine is impulse per unit of propellant, this is called specific impulse (usually written $I s p$ ). This is either measured as a speed ( $V e$ in metres/second or ft/s) or as a time (seconds). An engine that gives a large specific impulse is normally highly desirable.

[edit] Net thrust

Below is an approximate equation for calculating the net thrust of a rocket engine:

$F_n = \dot{m}\;V_{e} = \dot{m}\;V_{e-act} + A_{e}(P_{e} - P_{amb})$ ^[2]

where:

$\dot{m} = \,$ exhaust gas mass flow

$V_{e} =\,$ effective exhaust velocity

$V_{e-act} =\,$ actual jet velocity at nozzle exit plane

$A_{e} =\,$ flow area at nozzle exit plane

$P_{e} =\,$ static pressure at nozzle exit plane

$P_{amb} =\,$ ambient (or atmospheric) pressure

Since, unlike a jet engine, a conventional rocket motor lacks an air intake, there is no 'ram drag' to deduct from the gross thrust. Consequently the net thrust of a rocket motor is equal to the gross thrust (apart from static back pressure).

The $\dot{m}\;V_{e-act}\,$ term represents the momentum thrust, which remains constant at a given throttle setting, whereas the $A_{e}(P_{e} - P_{amb})\,$ term represents the pressure thrust term. At full throttle, the net thrust of a rocket motor improves slightly with increasing altitude, because the reducing atmospheric pressure increases the pressure thrust term.

If the pressure of the exhaust jet varies from atmospheric pressure, nozzles can be said to be underexpanded, ambient or overexpanded. If under or overexpanded then loss of efficiency occurs, grossly overexpanded nozzles lose less efficiency, but the exhaust jet is usually unstable. Rockets become progressively more underexpanded as they gain altitude. Note that almost all rocket engines will be momentarily grossly overexpanded during startup in an atmosphere.^[3]

[edit] Vacuum Isp

Due to the specific impulse varying with pressure, a quantity that is easy to compare and calculate with is useful. Because rockets choke at the throat, and because the supersonic exhaust prevents external pressure influences travelling upstream, it turns out that the pressure at the exit is ideally exactly proportional to the propellant flow $\dot{m}$ , provided the mixture ratios and combustion efficiencies are maintained. It is thus quite usual to rearrange the above equation slightly:

$Fvac = C_f \dot{m} c^*$ ^[4]

and so define the vacuum Isp to be:

V e v a c = C f c *

Where:

$c^* =\,$ the speed of sound constant at the throat

$C_f =\,$ the thrust coefficient constant of the nozzle (typically between 0.8 and 1.9)

And hence:

$F_n = \dot{m} V_{evac} - A_{e} P_{amb}$

[edit] Throttling

Rockets can be throttled by controlling the propellant rate $\dot{m}$ (usually measured in kg/s or lb/s).

In principle rockets can be throttled down to an exit pressure of about one-third of ambient pressure (due to flow separation in nozzles) and up to a maximum limit determined only be the mechanical strength of the engine.

In practice, the degree to which rockets can be throttled varies greatly, but most rockets may be throttled by a factor of 2 without great difficulty; the typical limitation is combustion stability, as for example, injectors need a minimum pressure to avoid triggering damaging oscillations (chugging or combustion instabilities); but injectors can often be optimised and tested for wider ranges. Additionally, it is important that the exit pressure not be too far below ambient to avoid flow separation in the nozzle.

[edit] Energy efficiency

Rocket energy efficiency as a function of vehicle speed divided by effective exhaust speed

Rocket engine nozzles are surprisingly efficient heat engines for generating a high speed jet, as a consequence of the high combustion temperature and high compression ratio in accordance with the carnot cycle. For a vehicle employing a rocket engine the energetic efficiency is very good if the vehicle speed approaches or somewhat exceeds the exhaust velocity (relative to launch); but at low speeds the efficiency asymptotically approaches 0% at zero speed (as with all jet propulsion.) See Rocket energy efficiency for more details.

[edit] Cooling

The reaction mass's combustion temperatures can typically reach ~3500 K (~5800 °F) which is often far higher than the melting point of the nozzle and combustion chamber materials, two exceptions are graphite and tungsten (~1200 K for copper). Indeed many construction materials can make perfectly acceptable propellants in their own right. It is important that these materials be prevented from combusting, melting or vapourising to the point of failure. Materials technology could potentially place an upper limit on the exhaust temperature of chemical rockets.

Alternatively, rockets may use more common construction materials such as aluminum, steel, nickel or copper alloys and employ cooling systems that prevent the construction material itself becoming too hot. Regenerative cooling, where the propellant is passed through tubes around the combustion chamber or nozzle, and other techniques, such as curtain cooling or film cooling, are employed to give longer nozzle and chamber life. These techniques ensure that a gaseous thermal boundary layer touching the material is kept below the temperature which would cause the material to catastrophically fail.

In rockets, the heat fluxes that can pass through the wall are among the highest in engineering, fluxes are generally in the range of 1-200 MW/m^2. The strongest heat fluxes are found at the throat, which often sees twice that found in the the associated chamber and nozzle. This is due to the combination of high speeds (which gives a very thin boundary layer), and the high temperatures seen there.

The coolant methods include:

uncooled (used for short runs mainly during testing)
ablative walls (walls are lined with a material that is continuously vapourised and carried away).
radiative cooling (the chamber becomes almost white hot and radiates the heat away)
dump cooling (a propellant, usually hydrogen, is passed around the chamber and dumped)
regenerative cooling (uses the propellant to cool the chamber via a cooling jacket before being injected)
curtain cooling (propellant injection is arranged so the temperature of the gases is cooler at the walls)
film cooling (surfaces are wetted with liquid propellant, which cools as it evaporates)

In all cases the cooling effect that prevents the wall from being destroyed is caused by a thin layer of insulating fluid (a boundary layer) that is in contact with the walls that is far cooler than the combustion temperature. Provided this boundary layer is intact the wall will not be damaged.

Disruption of the boundary layer may occur during cooling failures or combustion instabilities, and wall failure typically occurs soon after.

With regenerative cooling a second boundary layer is found in the coolant channels around the chamber. This boundary layer thickness needs to be as small as possible, since the boundary layer acts as an insulator between the wall and the coolant. This may be achieved by making the coolant velocity in the channels as high as possible.

[edit] Mechanical issues

Rocket combustion chambers are normally operated at fairly high pressure, typically 10-200 bar (1 to 20 MPa), higher pressures often give better performance (by permitting a more efficient nozzle to be fitted). This causes the outermost part of the chamber to be under very large hoop stresses.

Worse, due to the high temperatures created in rocket engines the materials used tend to have a significantly lowered working tensile strength.

[edit] Acoustic issues

In addition, the extreme vibration and acoustic environment inside a rocket motor commonly results in peak stresses well above mean values, especially in the presence of organ pipe-like resonances and gas turbulence.

[edit] Combustion

Three different types of combustion instabilities occur

Chugging

This is a low frequency oscillation at a few Hertz in chamber pressure usually caused by interaction between acceleration and chamber pressure. This causes cyclic variation in thrust, and the effects can vary from merely annoying to actually damaging the payload or vehicle. Chugging can be minimised by using gas filled damping tubes on feed lines of high density propellant's.

Buzzing

This can be caused due to insufficient pressure drop across the injectors. It generally is mostly annoying, rather than being damaging. However, in extreme cases combustion can end up being forced backwards through the injectors- this can cause explosions with monopropellants.

Screeching

This the most immediately damaging, and the hardest to control. It is due to acoustics within the combustion chamber that often couples to the chemical combustion processes that are the primary drivers of the energy release, and can lead to unstable resonant "screeching" that commonly leads to catastrophic failure due to thinning of the insulating thermal boundary layer^[5]. Such effects are very difficult to predict analytically during the design process, and have usually been addressed by expensive and time consuming extensive testing, combined with trial and error remedial correction measures.

Screeching is often dealt with by detailed changes to injectors, or changes in the propellant chemistry, or vaporizing the propellant before injection of the use of Helmholtz dampers within the combustion chambers to change the resonant modes of the chamber.

Testing for the possibility of screeching is sometimes done by exploding small explosive charges in the combustion chamber to determine the engine's impulse response and then evaluating the time response of the chamber pressure- a fast recovery indicates a stable system.

[edit] Exhaust noise

For all but the very smallest sizes, rocket exhaust compared to other engines is generally very noisy indeed. As the hypersonic exhaust mixes with the ambient air, shock waves are formed. The sound intensity from these shock waves depends on the size of the rocket, and on large rockets could potentially kill at close range.^[6]

The Saturn V launch was detectable on seismometers a considerable distance from the launch site. The sound intensity from the shock waves generated depends on the size of the rocket and on the exhaust velocity. Such shock waves seem to account for the characteristic crackling and popping sounds produced by large rocket engines when heard live. These noise peaks typically overload microphones and audio electronics, and so are generally weakened or entirely absent in recorded or broadcast audio reproductions. For large rockets the acoustic effects could actually kill. The Space Shuttle generates over 200 dB(A) of noise around its base.

Generally speaking noise is most intense when a rocket is close to the ground, since the noise from the engines radiates up away from the plume, as well as reflecting off the ground. Also, when the vehicle is moving slowly, little of the chemical energy input to the engine can go into increasing the kinetic energy of the rocket (since useful power P transmitted to the vehicle is $P = F * V$ for thrust F and speed V). Then the largest portion of the energy is dissipated in the exhaust's interaction with the ambient air, producing noise. This noise can be reduced somewhat by flame trenches with roofs, by water injection around the plume and by deflecting the plume at an angle.

[edit] Testing

Rocket engines are usually statically tested at a test facility before being put into production. For high altitude engines, either a shorter nozzle must be used, or the rocket must be tested in a large vacuum chamber.

[edit] Safety

Rockets have a reputation for unreliability and danger; especially catastrophic failures. Contrary to this reputation, carefully designed rockets can be made arbitrarily reliable. In military use, rockets are not unreliable. However, one of the main non-military uses of rockets is for orbital launch. In this application, the premium is on minimum weight, and it is difficult to achieve high reliability and low weight simultaneously. In addition, if the number of flights launched is low, there is a very high chance of a design, operations or manufacturing error causing destruction of the vehicle. Essentially all launch vehicles are test vehicles by normal aerospace standards (as of 2006).

The X-15 rocket plane achieved a 0.5% failure rate, with a single catastrophic failure during ground test, and the SSME has managed to avoid catastrophic failures in over 350 engine-flights.

[edit] Chemistry

Rocket propellants require a high specific energy (energy per unit mass), because ideally all the reaction energy appears as kinetic energy of the exhaust gases, and exhaust velocity is the single most important performance parameter of an engine, on which vehicle performance depends.

Aside from inevitable losses and imperfections in the engine, incomplete combustion, etc., after specific reaction energy, the main theoretical limit reducing the exhaust velocity obtained is that, according to the laws of thermodynamics, a fraction of the chemical energy may go into rotation of the exhaust molecules, where it is unavailable for producing thrust. Monatomic gases like helium have only three degrees of freedom, corresponding to the three dimensions of space, {x,y,z}, and only such spherically symmetric molecules escape this kind of loss. A diatomic molecule like H₂ can rotate about either of the two axes perpendicular to the one joining the two atoms, and as the equipartition law of statistical mechanics demands that the available thermal energy be divided equally among the degrees of freedom, for such a gas in thermal equilibrium 3/5 of the energy can go into unidirectional motion, and 2/5 into rotation. A triatomic molecule like water has six degrees of freedom, so the energy is divided equally among rotational and translational degrees of freedom. For most chemical reactions the latter situation is the case. This issue is traditionally described in terms of the ratio, gamma, of the specific heat of the gas at constant volume to that at constant pressure. The rotational energy loss is largely recovered in practice if the expansion nozzle is large enough to allow the gases to expand and cool sufficiently, the function of the nozzle being to convert the random thermal motions of the molecules in the combustion chamber into the unidirectional translation that produces thrust. As long as the exhaust gas remains in equilibrium as it expands, the initial rotational energy will be largely returned to translation in the nozzle.

Although the specific reaction energy per unit mass of reactants is key, low mean molecular weight in the reaction products is also important in practice in determining exhaust velocity. This is because the high gas temperatures in rocket engines pose serious problems for the engineering of survivable motors. Because temperature is proportional to the mean energy per molecule, a given amount of energy distributed among more molecules of lower mass permits a higher exhaust velocity at a given temperature. This means low atomic mass elements are favored. Liquid hydrogen (LH2) and oxygen (LOX, or LO2), are the most effective propellants in terms of exhaust velocity that have been widely used to date, though a few exotic combinations involving boron or liquid ozone are potentially somewhat better in theory if various practical problems could be solved^[7].

It is important to note in computing the specific reaction energy, that the entire mass of the propellants, including both fuel and oxidizer, must be included. The fact that air-breathing engines are typically able to obtain oxygen "for free" without having to carry it along, accounts for one factor of why air-breathing engines are very much more propellant-mass efficient, and one reason that rocket engines are far less suitable for most ordinary terrestrial applications. Fuels for automobile or turbojet engines, utilize atmospheric oxygen and and so have a much better effective energy output per unit mass of fuel that must be carried.

Computer programs that predict the performance of propellants in rocket engines are available.^[8].

[edit] Ignition

With liquid and hybrid rockets, immediate ignition of the propellant(s) as they first enter the combustion chamber is essential.

With liquid propellants (but not gaseous), failure to ignite within milliseconds usually causes too much liquid propellant to be within the chamber, and if/when ignition occurs the amount of hot gas created will often exceed the maximum design pressure of the chamber. The pressure vessel will often fail catastrophically. This is sometimes called a Hard start.

Ignition can be achieved by a number of different methods; a pyrotechnic charge can be used, the propellants can ignite spontaneously on contact (hypergolic), a plasma torch can be used, or electric spark plugs may be employed.

Gaseous propellants generally will not cause hard starts, with rockets the total injector area is less than the throat thus the chamber pressure tends to ambient prior to ignition and high pressures cannot form even if the entire chamber is full of flammable gas at ignition.

Solid propellants are usually ignited with one-shot pyrotechnic devices.

Once ignited, rocket chambers are self sustaining and igniters are not needed. Indeed chambers often spontaneously reignite if they are restarted after being shut down for a few seconds. However, when cooled, many rockets cannot be restarted without at least minor maintenance, such as replacement of the pyrotechnic igniter.

[edit] Types of rocket engines

[edit] Physically powered

Type	Description	Advantages	Disadvantages
water rocket	Partially filled pressurised carbonated drinks container with tail and nose weighting	Very simple to build	Altitude typically limited to a few hundred feet or so (world record is 623 meters/2044 feet)
cold gas thruster	A non combusting form, used for attitude jets	Non contaminating exhaust	Extremely low performance
hot water rocket	Hot water is stored in a tank at high temperature/pressure and turns to steam in exhaust	Simple, fairly safe	Low performance due to heavy tank

[edit] Chemically powered

See also: Liquid rocket propellants

Type	Description	Advantages	Disadvantages
Solid rocket	Ignitable, self sustaining solid fuel/oxidiser mixture ("grain") with central hole and nozzle	Simple, often no moving parts, reasonably good mass fraction, reasonable I_sp. A thrust schedule can be designed into the grain.	Once lit, extinguishing it is difficult although often possible, cannot be throttled in real time; handling issues from ignitable mixture, lower performance than liquid rockets, if grain cracks it can block nozzle with disastrous results, cracks burn and widen during burn. Refuelling grain harder than simply filling tanks, Lower specific Impulse than Liquid Rockets.
Hybrid rocket	Separate oxidiser/fuel, typically oxidiser is liquid and kept in a tank, the other solid with central hole	Quite simple, solid fuel is essentially inert without oxidiser, safer; cracks do not escalate, throttleable and easy to switch off.	Some oxidisers are monopropellants, can explode in own right; mechanical failure of solid propellant can block nozzle, central hole widens over burn and negatively affects mixture ratio.
Monopropellant rocket	Propellant such as Hydrazine, Hydrogen Peroxide or Nitrous Oxide, flows over catalyst and exothermically decomposes and hot gases are emitted through nozzle	Simple in concept, throttleable, low temperatures in combustion chamber	catalysts can be easily contaminated, monopropellants can detonate if contaminated or provoked, I_sp is perhaps 1/3 of best liquids
Bipropellant rocket	Two fluid (typically liquid) propellants are introduced through injectors into combustion chamber and burnt	Up to ~99% efficient combustion with excellent mixture control, throttleable, can be used with turbopumps which permits incredibly lightweight tanks, can be safe with extreme care	Pumps needed for high performance are expensive to design, huge thermal fluxes across combustion chamber wall can impact reuse, failure modes include major explosions, a lot of plumbing is needed.
Dual mode propulsion rocket	Rocket takes off as a bipropellant rocket, then turns to using just one propellant as a monopropellant	Simplicity and ease of control	Lower performance than bipropellants
Tripropellant rocket	Three different propellants (usually hydrogen, hydrocarbon and liquid oxygen) are introduced into a combustion chamber in variable mixture ratios, or multiple engines are used with fixed propellant mixture ratios and throttled or shut down	Reduces take-off weight, since hydrogen is lighter; combines good thrust to weight with high average I_sp, improves payload for launching from Earth by a sizeable percentage	Similar issues to bipropellant, but with more plumbing, more R&D
Air-augmented rocket	Essentially a ramjet where intake air is compressed and burnt with the exhaust from a rocket	Mach 0 to Mach 4.5+ (can also run exoatmospheric), good efficiency at Mach 2 to 4	Similar efficiency to rockets at low speed or exoatmospheric, inlet difficulties, a relatively undeveloped and unexplored type, cooling difficulties, very noisy, thrust/weight ratio is similar to ramjets.
Turborocket	A combined cycle turbojet/rocket where an additional oxidizer such as oxygen is added to the airstream to increase maximum altitude	Very close to existing designs, operates in very high altitude, wide range of altitude and airspeed	Atmospheric airspeed limited to same range as turbojet engine, carrying oxidizer like LOX can be dangerous. Much heavier than simple rockets.
Precooled jet engine / LACE (combined cycle with rocket)	Intake air is chilled to very low temperatures at inlet before passing through a ramjet or turbojet engine. Can be combined with a rocket engine for orbital insertion.	Easily tested on ground. High thrust/weight ratios are possible (~14) together with good fuel efficiency over a wide range of airspeeds, mach 0-5.5+; this combination of efficiencies may permit launching to orbit, single stage, or very rapid intercontinental travel.	Exists only at the lab prototyping stage. Examples include RB545, SABRE, ATREX

[edit] Electrically powered

Type	Description	Advantages	Disadvantages
Resistojet rocket (electric heating)	A monopropellant is electrically heated by a filament for extra performance	Higher I_sp than monopropellant alone, about 40% higher.	Uses a lot of power and hence gives typically low thrust
Arcjet rocket (chemical burning aided by electrical discharge)	Similar to resistojet in concept but with inert propellant, except an arc is used which allows higher temperatures	1600 seconds I_sp	Very low thrust and high power, performance is similar to Ion drive.
Pulsed plasma thruster (electric arc heating; emits plasma)	Plasma is used to erode a solid propellant	High I_sp , can be pulsed on and off for attitude control	Low energetic efficiency
Variable specific impulse magnetoplasma rocket	Microwave heated plasma with magnetic throat/nozzle	Variable I_sp from 1000 seconds to 10,000 seconds	similar thrust/weight ratio with ion drives (worse), thermal issues, as with ion drives very high power requirements for significant thrust, really needs advanced nuclear reactors, never flown, requires low temperatures for superconductors to work

See also: Ion thruster

[edit] Solar powered

The Solar thermal rocket would make use of solar power to directly heat reaction mass, and therefore does not require an electrical generator as most other forms of solar-powered propulsion do. A solar thermal rocket only has to carry the means of capturing solar energy, such as concentrators and mirrors. The heated propellant is fed through a conventional rocket nozzle to produce thrust. The engine thrust is directly related to the surface area of the solar collector and to the local intensity of the solar radiation.

Type	Description	Advantages	Disadvantages
Solar thermal rocket	Propellant is heated by solar collector	Reasonably simple, good performance with liquid hydrogen propellant, adequate performance with in-situ water for short-range interplanetary flight	only useful once in space, as thrust is fairly low, but hydrogen is not easily stored in space, otherwise moderate/low I_sp if higher molecular mass propellants are used

See also: Ion thruster

[edit] Beam powered

Type	Description	Advantages	Disadvantages
light beam powered rocket	Propellant is heated by light beam (often laser) aimed at vehicle from a distance, either directly or indirectly via heat exchanger	simple in principle, in principle very high exhaust speeds can be achieved	~1 MW of power per kg of payload is needed to achieve orbit, relatively high accelerations, lasers are blocked by clouds, fog, reflected laser light may be dangerous, pretty much needs hydrogen monopropellant for good performance which needs heavy tankage, some designs are limited to ~600 seconds due to reemission of light since propellant/heat exchanger gets white hot
microwave beam powered rocket	Propellant is heated by microwave beam aimed at vehicle from a distance	microwaves avoid reemission of energy, so ~900 seconds exhaust speeds might be achieveable	~1 MW of power per kg of payload is needed to achieve orbit, relatively high accelerations, microwaves are absorbed to a degree by rain, reflected microwaves may be dangerous, pretty much needs hydrogen monopropellant for good performance which needs heavy tankage, transmitter diameter is measured in kilometres to achieve a fine enough beam to hit a vehicle at up to 100km.

[edit] Nuclear powered

Nuclear propulsion includes a wide variety of propulsion methods that use some form of nuclear reaction as their primary power source. Various types of nuclear propulsion have been proposed, and some of them tested, for spacecraft applications:

Type	Description	Advantages	Disadvantages
Radioisotope rocket/"Poodle thruster" (radioactive decay energy)	Heat from radioactive decay is used to heat hydrogen	about 700-800 seconds, almost no moving parts	low thrust/weight ratio.
Nuclear thermal rocket (nuclear fission energy)	propellant (typ. hydrogen) is passed through a nuclear reactor to heat to high temperature	I_sp can be high, perhaps 900 seconds or more, above unity thrust/weight ratio with some designs	Maximum temperature is limited by materials technology, some radioactive particles can be present in exhaust in some designs, nuclear reactor shielding is heavy, unlikely to be permitted from surface of the Earth, thrust/weight ratio is not high.
Gas core reactor rocket (nuclear fission energy)	Nuclear reaction using a gaseous state fission reactor in intimate contact with propellant	Very hot propellant, not limited by keeping reactor solid, I_sp between 1500 and 3000 seconds but with very high thrust	difficulties in heating propellant without losing fissionables in exhaust, exhaust inherently highly radioactive, massive thermal issues particularly for nozzle/throat region.
Fission-fragment rocket (nuclear fission energy)	Fission products are directly exhausted to give thrust		Theoretical only at this point.
Fission sail (nuclear fission energy)	A sail material is coated with fissionable material on one side	No moving parts, works in deep space	Theoretical only at this point.
Nuclear salt-water rocket (nuclear fission energy)	Nuclear salts are held in solution, caused to react at nozzle	Very high I_sp, very high thrust	Thermal issues in nozzle, propellant could be unstable, highly radioactive exhaust. Theoretical only at this point.
Nuclear pulse propulsion (exploding fission/fusion bombs)	Shaped nuclear bombs are detonated behind vehicle and blast is caught by a 'pusher plate'	Very high I_sp, very high thrust/weight ratio, no show stoppers are known for this technology	Never been tested, pusher plate may throw off fragments due to shock, minimum size for nuclear bombs is still pretty big, expensive at small scales, nuclear treaty issues, fallout when used below Earth's magnetosphere.
Antimatter catalyzed nuclear pulse propulsion (fission and/or fusion energy)	Nuclear pulse propulsion with antimatter assist for smaller bombs	Smaller sized vehicle might be possible	Containment of antimatter, production of antimatter in macroscopic quantities isn't currently feasible. Theoretical only at this point.
Fusion rocket (nuclear fusion energy)	Fusion is used to heat propellant	Very high exhaust velocity	Largely beyond current state of the art.
Antimatter rocket (annihilation energy)	Antimatter annihilation heats propellant	Extremely energetic, very high theoretical exhaust velocity	Problems with antimatter production and handling; energy losses in neutrinos, gamma rays, muons; thermal issues. Theoretical only at this point

[edit] History of rocket engines

According to the writings of the Roman Aulus Gellius, in c. 400 BC, a Greek Pythagorean named Archytas, propelled a wooden bird along wires using steam.^[9] However, it would not appear to have been powerful enough to take off under its own thrust.

The aeolipile invented in the first century (known as Hero's engine) essentially consists of a hot water rocket on a bearing. It was created almost two millennia before the industrial revolution. Apparently Hero's steam engine was taken to be little more than a toy, the principles behind it were not well understood, and its full potential not realized for a millennium.

The availability of black powder to propel projectiles was a precursor to the development of the first solid rocket. Ninth Century Chinese Taoist alchemists discovered black powder in a search for the Elixir of life; this accidental discovery led to fire arrows which were the first rocket engines to leave the ground.

Slow development of this technology continued up to the later 20th Century, when the writings of Konstantin Tsiolkovsky first talked about liquid fuelled rocket engines.

These independently became a reality thanks to Robert Goddard.

[edit] References

^ Rocket Propulsion Elements; 7th edition- chapter 1
^ Rocket Propulsion Elements seventh edition eq-2-14
^ Huzel, D. K. and Huang, D. H. (1971). NASA SP-125, Design of Liquid Propellant Rocket Engines, 2nd Edition, NASA.
^ Rocket Propulsion Elements seventh edition eq-3-33
^ G.P. Sutton & D.M. Ross, Rocket Propulsion Elements, 4th Ed. 1975 (WileyInterscience New York), Ch 8, Sec 6 & especially Sec. 7, re combustion instability.
^ NASA CR-566
^ Newsgroup correspondence, 1998-99
^ Complex chemical equilibrium and rocket performance calculations, Cpropep-Web
^ Leofranc Holford-Strevens, Aulus Gellius: An Antonine Author and his Achievement (Oxford University Press; revised paperback edn. 2005)
- This article incorporates text from the Encyclopædia Britannica Eleventh Edition, a publication now in the public domain.

This article or section is missing citations or needs footnotes.
Using inline citations helps guard against copyright violations and factual inaccuracies. (September 2007)

[edit] See also

NERVA - NASA's Nuclear Energy for Rocket Vehicle Applications, a US nuclear thermal rocket programme
Project Prometheus, NASA development of nuclear propulsion for long-duration spaceflight, begun in 2003
Jet damping an effect of the exhaust jet of a rocket that tends to slow a vehicle's rotation speed

v • d • e

Heat engines

Stroke cycles

One · Two · Four · Six

Engine types

Gas turbine · Piston · Jet · Rocket engine · Steam engine · Stirling engine

Tschudi · Twingle

Rotary · Wankel · Free-piston · Britalus · Coomber · Swing-piston · Orbital · Quasiturbine

Valves

Cylinder head porting · Corliss · D slide · Four-stroke · Manifold · Multi · Piston · Poppet · Sleeve

Piston layouts

Single cylinder · Straight · Opposed · Flat · V · W · H · Deltic · Radial · Rocket engine nozzle · Rotary · Stelzer · Controlled Combustion · Bourke

Motion
mechanisms

Cam · Connecting rod · Coomber rotary · Crank · Crank substitute · Crankshaft · Linkages (Evans · Peaucellier-Lipkin · Sector straight-line · Watt) · Double acting/differential cylinder

Thermodynamic cycle

[edit] External links

Hidden categories: Articles with unsourced statements since September 2007 | All articles with unsourced statements