Power MOSFET

From Wikipedia, the free encyclopedia

Two power MOSFETs in the surface-mount package D2PAK. Each of these components can sustain a blocking voltage of 30 volts and a continuous current of 120 amperes.
Two power MOSFETs in the surface-mount package D2PAK. Each of these components can sustain a blocking voltage of 30 volts and a continuous current of 120 amperes.

A Power MOSFET is a specific type of Metal Oxide Semiconductor Field-Effect Transistor (MOSFET) designed to handle large power. Compared to the other power semiconductor devices (IGBT, Thyristor...), its main advantages are high commutation speed and good efficiency at low voltages. It shares with the IGBT an isolated gate that makes it easy to drive.


It was made possible by the evolution of the CMOS technology, developed for manufacturing Integrated circuits in the late 1970s. The power MOSFET shares its operating principle with its low-power counterpart, the lateral MOSFET.

The power MOSFET is the most widely used low-voltage (i.e. less than 200 V) switch. It can be found in most power supplies, DC to DC converters, and low voltage motor controllers.

Contents

[edit] Basic structure

Fig. 1: Cross section of a VDMOS, showing an elementary cell. Note that a cell is very small (some micrometres to some tens of micrometres wide), and that a power MOSFET is composed of several thousand of them.
Fig. 1: Cross section of a VDMOS, showing an elementary cell. Note that a cell is very small (some micrometres to some tens of micrometres wide), and that a power MOSFET is composed of several thousand of them.

Several structures had been explored at the beginning of the 1980s, when the first Power MOSFET were introduced. However, most of them have been abandoned (at least until recently) in favour of the Vertical Diffused MOS (VDMOS) structure (also called Double-Diffused MOS or simply DMOS).

The cross section of a VDMOS (see figure 1) shows the "verticality" of the device: It can be seen that the source electrode is placed over the drain, resulting in a current mainly vertical when the transistor is in the on-state. The "diffusion" in VDMOS refers to the manufacturing process: the P wells (see figure 1) are obtained by a diffusion process (actually a double diffusion process to get the P and N+ regions, hence the name double diffused).

Power MOSFETs have a different structure than the lateral MOSFET: as with all power devices, their structure is vertical and not planar. In a planar structure, the current and breakdown voltage ratings are both functions of the channel dimensions (respectively width and length of the channel), resulting in inefficient use of the "silicon estate". With a vertical structure, the voltage rating of the transistor is a function of the doping and thickness of the N epitaxial layer (see cross section), while the current rating is a function of the channel width. This makes possible for the transistor to sustain both high blocking voltage and high current within a compact piece of silicon.

It is worth noting that power MOSFETs with lateral structure exist. They are mainly used in high-end audio amplifiers. Their advantage is a better behaviour in the saturated region (corresponding to the linear region of a bipolar transistor) than the vertical MOSFETs. Vertical MOSFETs are designed for switching applications, so they are only used in On or Off states.

[edit] On-state characteristics

[edit] On-state resistance

Fig.2: Contribution of the different parts of the MOSFET to the on-state resistance.
Fig.2: Contribution of the different parts of the MOSFET to the on-state resistance.

When the power MOSFET is in the on-state (see MOSFET for a discussion on operation modes), it exhibits a resistive behaviour between the drain and source terminals. It can be seen in figure 2 that this resistance (called RDSon for "drain to source resistance in on-state") is the sum of many elementary contributions:

  • RS is the source resistance. It represents all resistances between the source terminal of the package to the channel of the MOSFET: resistance of the wire bonds, of the source metallisation, and of the N+ wells;
  • Rch. This is the channel resistance. It is directly proportional to the channel width, and for a given die size, to the channel density. The channel resistance is one of the main contributors to the RDSon of low-voltage MOSFETs, and intensive work has been carried out to reduce their cell size in order to increase the channel density;
  • Ra is the access resistance. It represents the resistance of the epitaxial zone directly under the gate electrode, where the direction of the current changes from horizontal (in the channel) to vertical (to the drain contact);
  • RJFET is the detrimental effect of the cell size reduction mentioned above: the P implantations (see figure 1) form the gates of a parasitic JFET transistor that tend to reduce the width of the current flow;
  • Rn is the resistance of the epitaxial layer. As the role of this layer is to sustain the blocking voltage, Rn is directly related to the voltage rating of the device. A high voltage MOSFET requires a thick, low-doped layer (i.e. highly resistive), whereas a low-voltage transistor only requires a thin layer with a higher doping level (i.e. less resistive). As a result, Rn is the main factor responsible for the resistance of high-voltage MOSFETs;
  • RD is the equivalent of RS for the drain. It represents the resistance of the transistor substrate (note that the cross section in figure 1 is not at scale, the bottom N+ layer is actually the thickest) and of the package connections.

[edit] Breakdown voltage/on-state resistance trade-off

Fig. 3: The RDSon of the MOSFETs increase with their Voltage rating.
Fig. 3: The RDSon of the MOSFETs increase with their Voltage rating.

When in the OFF-state, the power MOSFET is equivalent to a PIN diode (constituted by the P + diffusion, the N- epitaxial layer and the N+ substrate). When this highly non-symmetrical structure is reverse-biased, the space-charge region extends principally on the light-dopped side, i.e over the N- layer. This means that this layer has to withstand most of the MOSFET's OFF-state drain-to-source voltage.

However, when the MOSFET is in the ON-state, this N- layer has no function. Furthermore, as it is a lightly-doped region, its intrinsic resistivity is non-negligible and adds to the MOSFET's ON-state Drain-to-Source Resistance (RDSon) (this is the Rn resistance in figure 2).

Two main parameters govern both the breakdown voltage and the RDSon of the transistor: the doping level and the thickness of the N- epitaxial layer. The thicker the layer and the lower its doping level, the higher the breakdown voltage. On the contrary, the thinner the layer and the higher the doping level, the lower the RDSon (and therefore the lower the conduction losses of the MOSFET). Therefore, it can be seen that there is a trade-off in the design of a MOSFET, between its voltage rating and its ON-state resistance. This is demonstrated by the plot in figure 3.

[edit] Body diode

It can be seen in figure 1 that the source metallization connects both the N+ and P implantations, although the operating principle of the MOSFET only requires the source to be connected to the N+ zone. However, if it were, this would result in a floating P zone between the N-doped source and drain, which is equivalent to a NPN transistor with a non-connected base. Under certain conditions (under high drain current, when the on-state drain to source voltage is in the order of some volts), this parasitic NPN transistor would be triggered, making the MOSFET uncontrollable. The connection of the P implantation to the source metallization shorts the base of the parasitic transistor to its emitter (the source of the MOSFET) and thus prevents spurious latching.

This solution, however, creates a diode between the drain (cathode) and the source (anode) of the MOSFET, making it able to block current in only one direction.

[edit] Switching Operation

Fig. 4: Location of the intrinsic capacitances of a power MOSFET.
Fig. 4: Location of the intrinsic capacitances of a power MOSFET.

Because of their unipolar nature, the power MOSFET can switch at very high speed. Indeed, there is no need to remove minority carriers as with bipolar devices.

The only intrinsic limitation in commutation speed is due to the internal capacitances of the MOSFET (see figure 4). These capacitances must be charged or discharged when the transistor switches. This can be a relatively slow process because the current that flows through the gate capacitances is limited by the external driver circuit. This circuit will actually dictate the commutation speed of the transistor (assuming the power circuit has sufficiently low inductance).

[edit] Capacitances

In the MOSFETs datasheets, the capacitances are often named Ciss (input capacitance, drain and source terminal shorted), Coss (output capacitance, gate and source shorted), and Crss (reverse capacitance, gate and source shorted). The relationship between these capacitances and thoses described below is:

\begin{matrix} C_{iss} & = & C_{GS}+C_{GD}\\ C_{oss} & = & C_{GD}+C_{DS}\\ C_{rss} & = & C_{GD} \end{matrix}

Where CGS, CGD and CDS are respectively the gate-to-source, gate-to-drain and drain-to-source capacitances (see below). Manufacturers prefer to quote Ciss, Coss and Crss because they can be directly measured on the transistor. However, as CGS, CGD and CDS are closer to the physical meaning, they will be used in the remaining of this article.

[edit] Gate to source capacitance

The CGS capacitance is constituted by the parallel connection of CoxN+, CoxP and Coxm (see figure 4). As the N+ and P regions are highly doped, the two former capacitances can be considered as constant. Coxm is the capacitance between the (polysilicon) gate and the (metal) source electrode, so it is also constant. Therefore, it is common practice to consider CGS as a constant capacitance, i.e its value does not depend on the transistor state.

[edit] Gate to drain capacitance

The CGD capacitance can be seen as the connection in series of two elementary capacitances. The first one is the oxide capacitance (CoxD), constituted by the gate electrode, the silicon dioxide and the top of the N epitaxial layer. It has a constant value. The second capacitance (CCDj) is caused by the extension of the space-charge zone when the MOSFET is in off-state (see the section Blocking Voltage). Therefore, it is dependent upon the drain to source voltage. From this, the value of CGD is:

C_{GD}=\frac{C_{oxD}\times C_{GDj}\left(V_{GD}\right)}{C_{oxD}+ C_{GDj}\left(V_{GD}\right)}

The width of the space-charge region is given by [1]

w_{GDj}=\sqrt{\frac{2\epsilon_{Si}V_{GD}}{qN}}

where εSi is the permittivity of the Silicon, q is the electron charge, and N is the doping level. The value of CGDj can be approximated using the expression of the plane capacitor:

C_{DGj}=A_{GD}\frac{\epsilon_{Si}}{w_{GDj}}

Where AGD is the surface area of the gate-drain overlap. Therefore, it comes:

C_{GDj}\left(V_{GD}\right)=A_{GD}\sqrt{\frac{q\epsilon_{Si}N}{2V_{GD}}}

It can be seen that CGDj (and thus CGD) is a capacitance which value is dependent upon the gate to drain voltage. As this voltage increases, the capacitance decreases. When the MOSFET is in on-state, CGDj is shunted, so the gate to drain capacitance remains equal to CoxD, a constant value.

[edit] Drain to source capacitance

As the source metallization overlaps the P-wells (see figure 1), the drain and source terminals are separated by a P-N junction. Therefore, CDS is the junction capacitance. This is a non-linear capacitance, and its value can be calculated using the same equation as for CGDj.

[edit] Other dynamic elements

Equivalent circuit of a power MOSFET, including the dynamic elements (capacitors, inductors), the parasitic resistors, the body diode.
Equivalent circuit of a power MOSFET, including the dynamic elements (capacitors, inductors), the parasitic resistors, the body diode.

[edit] Packaging inductances

To operate, the MOSFET must be connected to the external circuit, most of the time using wire bonding (although alternative techniques are investigated). These connection exhibit a parasitic inductance, which is in no way specific to the MOSFET technology, but has important effects because of its high commutation speed. Parasitic inductances tend to maintain their current constant and generate overvoltage during the transistor turn off, resulting in increasing commutation losses.

A parasitic inductance can be associated with each terminal of the MOSFET. They have different effects:

  • turn on losses. However, as it creates an overvoltage during turn-off, it increases turn-off losses;
  • the source parasitic inductance has the same behaviour as the drain inductance, plus a feedback effect that makes commutation last longer, thus increasing commutation losses.
    • at the beginning of a fast turn-on, due to the source inductance, the voltage at the source (on the die) will be able to jump up as well as the gate voltage; the internal VGS voltage will remain low for a longer time, therefore delaying turn-on.
    • at the beginning of a fast turn-off, as current through the source inductance decreases sharply, the resulting voltage across it goes negative (with respect to the lead outside the package) raising the internal VGS voltage, keeping the MOSFET on, and therefore delaying turn-off.

[edit] Limits of operation

[edit] Gate oxide breakdown

The gate oxide is very thin (100 nm or less), so it can only sustain a limited voltage. In the datasheets, manufacturers often state a maximum gate to source voltage, around 20 V, and exceeding this limit can result in destruction of the component. Furthermore, a high gate to source voltage reduces significantly the lifetime of the MOSFET, with little to no advantage on RDSon reduction.

[edit] Maximum drain to source voltage

Power MOSFETS have a maximum specified drain to source voltage, beyond which breakdown may occur. Exceeding the breakdown voltage causes the device to turn on, potentially damaging it and other circuit elements due to excessive power dissipation.

[edit] Maximum drain current

The drain current must generally stay below a certain specified value (maximum continuous drain current). It can reach higher values for very short durations of time (maximum pulsed drain current, sometimes specified for various pulse durations). The drain current is limited by heating due to resistive losses in internal components such as bond wires, and other phenomena such as electromigration in the metal layer.

[edit] Maximum temperature

The junction temperature of the MOSFET must stay under a specified maximum value for the device to function reliably. How high above ambient temperature this is, is given by the power dissipation times thermal resistance. The junction-to-case thermal resistance is intrinsic to the device; the case-to-ambient thermal resistance sss can be lowered as much as practical by using an appropriately sized heatsink.

[edit] Safe operating area

The safe operating area defines the combined ranges of drain current and drain to source voltage the power MOSFET is able to handle without damage. It is represented graphically as an area in the plane defined by these two parameters. Both drain current and drain to source voltage must stay below their respective maximum values, but their product must also stay below the maximum power dissipation the device is able to handle. Thus the device cannot be operated at both its specified maximum drain current and maximum drain to source voltage. [2]

[edit] Latch Up Problem

The equivalent circuit for a MOSFET consist of one MOSFET in parallel with a parasitic BJT. If the BJT turns ON, it cannot be turned off since the gate has no control over it. This problem is known as latch up, which can lead to device destruction. The BJT can be turned on due to a voltage drop across the p-type body region. To avoid latch up, the body and the source are short circuited externally.

[edit] Technology

[edit] Layout

[edit] Cellular structure

This Power MOSFET has a meshed gate, with square cells
This Power MOSFET has a meshed gate, with square cells
The gate layout of this MOSFET is constituted of parallel stripes.
The gate layout of this MOSFET is constituted of parallel stripes.

As described above, the current handling capability of a power MOSFET is determined by its gate channel width. The gate channel width is the third (Z-axis) dimension of the cross-sections pictured.

To minimize cost and size, it is valuable to keep the transistor's die area size as small as possible. Therefore, optimizations have been developed to increase the width of the channel surface area (i.e increase the "channel density"). They mainly consist of creating cellular structures repeated over the whole area of the MOSFET die. Several shapes have been proposed for these cells, the most famous being the International Rectifier's "Hexfet" (hexagonal shape).

Another way to increase the channel density is to reduce the size of the elementary structure. This allows for more cells in a given surface area, and therefore more channel width. However, as the cell size shrinks, it becomes more difficult to ensure proper contact of every cell. To overcome this, a "strip" structure is often used (see figure). It is less efficient than a cellular structure of equivalent resolution in terms of channel density, but can cope with smaller pitch.

[edit] Structures

[edit] P-substrate power MOSFET

A P-substrate MOSFET (often referred to as PMOS) is a MOSFET with opposite doping types (N instead of P and P instead of N in the cross-section in figure 1). This MOSFET is made using a P-type substrate, with a P- epitaxy. As the channel sits in a N-region, this transistor is turned on by a negative gate to source voltage. This makes it desirable in a buck converter, where one of the terminals of the switch is connected to the high side of the input voltage: with a N-MOSFET, this configuration requires to apply to the gate a voltage equal to Vin + VGS, whereas no voltage over Vin is required with a P-MOSFET.

The main disadvantage of this type of MOSFET is the poor on-state performance: it uses holes as charge carriers, which have a much lower mobility than electrons. As resistivity is directly related to mobility, a given PMOS will have a RDSon three times higher than a N-MOSFET with the same dimensions.

[edit] VMOS

This structure was used for the first commercial devices [3].

[edit] UMOS

The UMOS has a trench gate. It is intended to increase the channel density by making the channel vertical
The UMOS has a trench gate. It is intended to increase the channel density by making the channel vertical

In this Power MOSFET structure, the gate electrode is buried in a trench etched in the silicon. This results in a vertical channel. The main interest of the structure is the absence of the JFET effect. The name of the structure comes from the U-shape of the trench.

[edit] CoolMOS

Especially for voltages beyond 500V some manufacturers, most notably Infineon Technologies, have begun to use a charge compensation principle. Thus the resistance in the epitaxial layer as biggest contributor in high voltage MOSFETs can be reduced by a factor >5.

[edit] See also

[edit] Notes

  1. ^ S. M. Sze Modern semiconductor device physics John Wiley and Sons, Inc 1998 ISBN 0-471-15237-4
  2. ^ Pierre Aloïsi, Les transistors MOS de puissance in Interrupteurs électroniques de puissance, traite EGEM, under the direction of Robert Perret, Lavoisier, Paris, 2003 [in french] ISBN 2-7462-0671-4
  3. ^ Duncan A. Grant, John Gowar POWER MOSFETS: Theory and Applications John Wiley and Sons, Inc ISBN 0-471-82867-X , 1989

[edit] References

  • "Power Semiconductor Devices", B. Jayant Baliga, PWS publishing Company, Boston. ISBN 0-534-94098-6