Photovoltaic module

From Wikipedia, the free encyclopedia

This article may require cleanup to meet Wikipedia's quality standards.
Please improve this article if you can. (June 2007)

A photovoltaic module is composed of individual PV cells. This crystalline-silicon module has an aluminium frame and glass on the front.

In the field of photovoltaics, a photovoltaic module is a packaged interconnected assembly of photovoltaic cells, also known as solar cells. An installation of photovoltaic modules or panels is known as a photovoltaic array or a solar panel. Photovoltaic cells typically require protection from the environment. For cost and practicality reasons a number of cells are connected electrically and packaged in a photovoltaic module, while a collection of these modules that are mechanically fastened together, wired, and designed to be a field-installable unit, sometimes with a glass covering and a frame and backing made of metal, plastic or fiberglass, are known as a photovoltaic panel or simply solar panel. A photovoltaic installation typically includes an array of photovoltaic modules or panels, an inverter, batteries (for off grid) and interconnection wiring.

1 Theory and construction
2 Rigid thin-film modules
3 Flexible thin-film modules
4 References
5 See also
6 External links

[edit] Theory and construction

The majority of modules use wafer-based Crystalline silicon cells or a thin film cell based on cadmium telluride or silicon (see photovoltaic cells for details)

In order to use the cells in practical applications, they must be:

connected electrically to one another and to the rest of the system
protected from mechanical damage during manufacture, transport and installation and use (in particular against hail impact, wind and snow loads). This is especially important for wafer-based silicon cells which are brittle.
protected from moisture, which corrodes metal contacts and interconnects, (and for thin film cells the transparent conductive oxide layer) thus decreasing performance and lifetime.
electrically insulated including under rainy conditions
mountable on a substructure

Most modules are rigid, but there are some flexible modules available, based on thin film cells.

Electrical connections are made in series to achieve a desired output voltage and/or in parallel to provide a desired amount of current source capability. Diodes are included to avoid overheating of cells in case of partial shading.

Since cell heating reduces the operating efficiency it is desirable to minimize the heating. Very few modules incorporate any design features to decrease temperature, however installers try to provide good ventilation behind the module,

New designs of module include concentrator modules in which the light is concentrated by an array of lenses or mirrors onto an array of small cells. This allows the use of cells with a very high cost per unit area (such as gallium arsenide) in a cost-competitive way.

Depending on construction the photovoltaic can cover a range of frequencies of light and can produce electricity from them, but cannot cover the entire solar spectrum. Hence much of incident sunlight energy is wasted when used for solar panels, although they can give far higher efficiencies if illuminated with monochromatic light. Another design concept is to split the light into different wavelength ranges and direct the beams onto different cells tuned to the appropriate wavelength ranges. ^[1] This is projected to raise efficiency to 50%. Sunlight conversion rates (module efficiencies) can vary from 5-18% in commercial production.

[edit] Rigid thin-film modules

In rigid thin film modules, the cell and the module are manufactured in the same production line.

The cell is created directly on a glass substrate or superstrate, and the electrical connections are created in situ, a so called "monolithic integration". The substrate or superstrate is laminated with an encapsulant to a front or back sheet, usually another sheet of glass.

The main cell technologies in this category are CdTe, amorphous silicon, micromorphous silicon (alone or tandem), or CIGS (or variant). Amorphous silicon has a sunlight conversion rate of 5-9%.

[edit] Flexible thin-film modules

Flexible thin film cells and modules are created on the same production line by depositing the photoactive layer and other necessary layers on a flexible substrate. If the substrate is an insulator (e.g. polyester or polyimide film) then monolithic integration can be used. If it is a conductor then another technique for electrical connection must be used. The cells are assembled into modules by laminating them to a transparent colourless fluoropolymer on the front side (typically ETFE or FEP) and a polymer suitable for bonding to the final substrate on the other side. The only commercially available (in MW quantities) flexible module uses amorphous silicon triple junction (from Unisolar).