Phillips Panda

From Wikipedia, the free encyclopedia

The Phillips Panda was one of a number of mopeds produced by the Phillips Cycles company of England in the 1950s and early 1960s. The factory also produced the slightly more expensive Phillips Gadabout models.

Phillips Cycles Ltd. was a respected British bicycle manufacturer based in Bridge Street, Smethwick, England. Founded by Walter Phillips around 1880, its history ended in the 1980s, by which time it had become part of Raleigh Industries, itself a part of the huge Tube Investments group. For a number of years, the Company was the second-largest bicycle producer in Britain after Raleigh. The "Phillips" brand is still used around the world, especially in China and the Far East, having been licensed by Raleigh.

[edit] General Description

(Acknowledgements to Mark Daniels and "Buzzing").

The single-speed Panda Mark 1 & 2 utilised what probably became the last manufacturing installation of the 49cc German Rex cyclemotor engine which first appeared around 1950 in the form of a front mounted belt driven cycle attachment, the strong but basic Panda frame being specifically built to house the motor.

The Rex engine at 6:1 compression has no bhp given but carries a 12-millimetre Bing carburettor to the aluminium barrel with sleeve liner in conventional fore & aft porting layout. The crankcase cavity unusually extends all the way to the back of the motor to include lubrication of the reduction gear and its bearings by the induction gases! This results in a reduced scavenge pressure. Mounted on the end of the output shaft with the sprocket inboard, the tiny 2½" Rex dry clutch is a particularly frail pull-operated device and typically responsible for the final demise of most machines.

The Panda has a 'grip-locking' clutch lever and a carburettor set-up that provides a very reliable and steady tick-over. The rear brake comprises a back pedal Perry Coaster hub and a conventional bicycle-type hub brake, handlebar lever operated for the front brake.

Mark 1 version had no suspension but the mark 2 had telescopic front forks, larger headlamp and deeper valanced rear mudguard but retained the solid rear frame.

The electrical system comprised a Miller flywheel magneto with lighting coils.

The final Panda mark 3 was simply an imported French Mobylette made by Motobécane badged as a Phillips. It had nothing in common with the previous home-produced models.

[edit] Technical Specification (Mark 1 & 2)

Engine:

• Rex air cooled, single cylinder,two-stroke.
• bore 40.5 mm.
• stroke 38.25 mm.
• capacity 49cc.
• compression ratio 6:1.
• Single Gear Ratio 17.3:1.

Clutch

• Rex Dry multi-plate.

Carburettor

• Bing model 1/12/27.

Ignition & Lighting

• Miller flywheel magneto 6 volt 18 watt (Headlamp 6v 15/15w, tail lamp 6v 3w).

Lubrication

• Petroil mixture 16:1.

Fuel Tank

• Approx 4 litres including 0.4 litres reserve.

Brakes:

• Front - 3.5 inch hub (mark 1), handlebar lever operated.
• Rear - Back pedalling Perry Coaster Hub

Tyres

• 23 X 2 inch with Schrader type valves.

Size

• Overall length 1820mm, height 940mm, width 152mm

Total Weight

• Approx 32 Kg.

Equipment

• 3.5 inch headlamp (mark 1), electric horn, bipod stand, rear carrier, tyre inflator, large tool bag and tool kit.

Finish

• Silver Grey with tank and fairings in Flamboyant Red.

[edit] On The Road

On sitting astride the Panda, ones first impression is immediately of how small the moped feels with its 23 inch wheels and upright riding position. Starting the machine is easy with a push-down button choke on the Bing carburettor and decompressor lever on the right hand handlebar. Once started on its stand with the clutch disengaged, the choke is reset by fully opening the twist-grip throttle momentarily.

Pulling away from rest is easily achievable without pedal assistance owing to the relatively high torque the motor delivers but this is not recommended practice as the frail clutch will fail rapidly with this sort of treatment. Pedal assisted starts are therefore much recommended. In fact, engine starting can be done by pedalling away from rest with the clutch engaged using the decompressor.

Once under way the machine pulls strongly up to about 25 mph but any increase tails off rapidly only just managing 30 mph in favourable conditions. This is no doubt due to the fairly low single speed gearing but it does enable most hills to be tackled without resort to pedalling.

The Rex engine is, however, stoically consistent and reliable. Always a reliable starter under all conditions and a reliable and consistent runner, though you do need time on your side to enjoy the docile character of the machine. The low maximum speed is compensated for to some extent by a good fuel consumption of 180 – 200 mpg. In common with most 'British' two-stroke machines of the time, the petroil mixture recommended is a little cautious erring on the 'oily' side at 16:1 using self-mixing two-stroke oil (16 parts of petrol to 1 part oil). The manual advises stretching it to 20:1 if using SAE20 motor engine oil. This British tendency to add rather more oil than the Continentals gave two-stokes a 'blue smokey exhaust' reputation in the UK but the Panda exhaust is not particularly smokey.

The low riding position gives the moped a 'safe' feeling to ride and the sturdy cycle frame seems to plough through road bumps reasonably well despite having no suspension front or rear on the mark 1 version.

The Phillips Panda looks quite pleasant once the side panels are fitted, hiding the rather ugly frame construction in the engine mounting area.

Night riding is no problem but headlamp illumination is a little dismal at 15watt and surprisingly has a main/dip feature !

Accessories available included a pair of plastic legshields and a windscreen.

As a reliable work horse, the Panda makes a sensible choice despite not having the performance of some of its continental competitors. Phillips set out to produce a reliable machine that was cheaper than most of its rivals. The Panda mark 1 cost £54-11s-0d in 1960.