Parametric oscillator

From Wikipedia, the free encyclopedia

A parametric oscillator is a simple harmonic oscillator whose parameters (its resonance frequency $ω$ and damping $β$ ) vary in time in a defined way

Another intuitive way of understanding a parametric oscillator is as follows:- a parametric oscillator is a device that oscillates when one of its "Parameters" [a physical entity, like capacitance] is changed.

The classical Tunnel Diode parametric oscillator broke into oscillations when its capacitance was suddenly changed with a regular period. The periodic capacitance change caused the diode and the associated tuned circuit to break into oscillations. The capacitance changing circuit was called the pump or driver.

In the Microwave world, Waveguide/YAG based parametric oscillators operated in the same fashion. The designer would change a parameter [a physical part of the system]

In the same manner, periodically changing the CG of a swing makes it go into oscillations.

1 Overview
2 History
3 The mathematics
4 Transformation of the equation
5 Solution of the transformed equation
6 Intuitive derivation of parametric excitation
7 Parametric amplifiers
8 Other relevant mathematical results
9 Low noise
10 References
11 Further reading
12 See also

[edit] Overview

A Parametric amplifier is basically a mixer. The Mixer gain shows up in the output as amplifier gain. The input weak signal is mixed with a strong Local Oscillator signal, and the resultant strong output is used in the ensuing receiver stages.

Parametric Amplifiers also operate by changing a parameter of the amplifier. Intuitively, this can be understood as follows, for a variable capacitor based amplifier.

Q [charge in a capacitor] = C x V
therefore
V [voltage across a capacitor] = Q/C

Knowing the above, if we charge a capacitor with a sampled voltage from an incoming weak signal, and then reduce its capacitance (say, by manually moving the plates further apart), then the voltage across the capacitor will increase. This simple fact gives us Voltage Amplification.

If the capacitor is a varicap diode, then the 'moving the plates' can be done simply by applying time-varying DC voltage to the varicap diode. This driving voltage is usually comes from another oscillator — sometimes called a pump.

The resulting output signal contains frequencies that are sum and difference of the input signal and the pump signal [f1 + f2] and [f1 - f2].

[edit] History

Faraday (1831) was the first to notice oscillations of one frequency being excited by forces of double the frequency, in the crispations (ruffled surface waves) observed in a wine glass excited to "sing". Melde (1859) generated parametric oscillations in a string by employing a tuning fork to periodically vary the tension at twice the resonance frequency of the string. Parametric oscillation was first treated as a general phenomenon by Rayleigh (1883,1887), whose papers are still worth reading today.

Parametric oscillators have been developed as low-noise amplifiers, especially in the radio and microwave frequency range. Thermal noise is minimal, since a reactance (not a resistance) is varied. Another common use is frequency conversion, e.g., conversion from audio to radio frequencies. Parametric amplifiers (paramps) were first used in 1913-1915 for radio telephony from Berlin to Vienna and Moscow, and were predicted to have a useful future (Alexanderson, 1916). The early paramps varied inductances, but other methods have been developed since, e.g., the varactor diodes, klystron tubes, Josephson junctions and optical methods. A practical parametric oscillator needs the following connections: one for common, one to feed the pump, one to retrieve the oscillation, and maybe a fourth one for biasing. A parametric amplifier needs a fifth port for the seed. Since a varactor diode has only two connections, it can only be a part of an LC network with four eigenvectors with nodes at the connections. This can be implemented as a transimpedance amplifier, a traveling wave amplifier or by means of a circulator.

[edit] The mathematics

$\frac{d^{2}x}{dt^{2}} + \beta(t) \frac{dx}{dt} + \omega^{2}(t) x = 0$

This equation is linear in $x (t)$ . By assumption, the parameters $ω 2$ and $β$ depend only on time and do not depend on the state of the oscillator. In general, $β(t)$ and/or $ω 2 (t)$ are assumed to vary periodically, with the same period $T$ .

Remarkably, if the parameters vary at roughly twice the natural frequency of the oscillator (defined below), the oscillator phase-locks to the parametric variation and absorbs energy at a rate proportional to the energy it already has. Without a compensating energy-loss mechanism, the oscillation amplitude grows exponentially. (This phenomenon is called parametric excitation, parametric resonance or parametric pumping.) However, if the initial amplitude is zero, it will remain so; this distinguishes it from the non-parametric resonance of driven simple harmonic oscillators, in which the amplitude grows linearly in time regardless of the initial state.

A familiar experience of parametric oscillation is playing on a swing. By alternately raising and lowering their center of mass (and thereby changing their moment of inertia, and thus the resonance frequency) at key points in the swing, children can quickly reach large amplitudes provided that they have some amplitude to start with (e.g., get a push). Doing so at rest, however, goes nowhere.

[edit] Transformation of the equation

We begin by making a change of variables

$q(t) \ \stackrel{\mathrm{def}}{=}\ e^{D(t)} x(t)$

where $D (t)$ is a time integral of the damping

$D(t) \ \stackrel{\mathrm{def}}{=}\ \frac{1}{2} \int^{t} d\tau \ \beta(\tau).$

This change of variables eliminates the damping term

$\frac{d^{2}q}{dt^{2}} + \Omega^{2}(t) q = 0$

where the transformed frequency is defined

$\Omega^{2}(t) = \omega^{2}(t) - \frac{1}{2} \left( \frac{d\beta}{dt} \right) - \frac{1}{4} \beta^{2}.$

In general, the variations in damping and frequency are relatively small perturbations

$\beta(t) = \omega_{0} \left[b + g(t) \right]$

$\omega^{2}(t) = \omega_{0}^{2} \left[1 + h(t) \right]$

where $ω 0$ and $b ω 0$ are constants, namely, the time-averaged oscillator frequency and damping, respectively. The transformed frequency can be written in a similar way:

$\Omega^{2}(t) = \omega_{n}^{2} \left[1 + f(t) \right],$

where $ω n$ is the natural frequency of the damped harmonic oscillator

$\omega_{n}^{2} \ \stackrel{\mathrm{def}}{=}\ \omega_{0}^{2} \left( 1 - \frac{b^{2}}{4} \right)$

and

$\omega_{n}^{2} f(t) \ \stackrel{\mathrm{def}}{=}\ \omega_{0}^{2} h(t) - \frac{1}{2\omega_{0}} \left( \frac{dg}{dt} \right) - \frac{b}{2} g(t) - \frac{1}{4} g^{2}(t).$

Thus, our transformed equation can be written

$\frac{d^{2}q}{dt^{2}} + \omega_{n}^{2} \left[1 + f(t) \right] q = 0.$

Remarkably, the independent variations $g (t)$ and $h (t)$ in the oscillator damping and resonance frequency, respectively, can be combined into a single pumping function $f (t)$ . The converse conclusion is that any form of parametric excitation can be accomplished by varying either the resonance frequency or the damping, or both.

[edit] Solution of the transformed equation

Let us assume that $f (t)$ is sinusoidal, specifically

f (t) = f 0 sin2ω p t

where the pumping frequency $2\omega_{p} \approx 2\omega_{n}$ but need not equal $2ω n$ exactly. The solution $q (t)$ of our transformed equation may be written

q (t) = A (t)cosω p t + B (t)sinω p t

where we have factored out the rapidly varying components ( $cosω p t$ and $sinω p t$ ) to isolate the slowly varying amplitudes $A (t)$ and $B (t)$ . This corresponds to Laplace's variation of parameters method.

Substituting this solution into the transformed equation and retaining only the terms first-order in $f_{0} \ll 1$ yields two coupled equations

$2\omega_{p} \frac{dA}{dt} = \left( \frac{f_{0}}{2} \right) \omega_{n}^{2} A - \left( \omega_{p}^{2} - \omega_{n}^{2} \right) B$

$2\omega_{p} \frac{dB}{dt} = -\left( \frac{f_{0}}{2} \right) \omega_{n}^{2} B + \left( \omega_{p}^{2} - \omega_{n}^{2} \right) A$

We may decouple and solve these equations by making another change of variables

$A(t) \ \stackrel{\mathrm{def}}{=}\ r(t) \cos \theta(t)$

$B(t) \ \stackrel{\mathrm{def}}{=}\ r(t) \sin \theta(t)$

which yields the equations

$\frac{dr}{dt} = \left( \alpha_{\mathrm{max}} \cos 2\theta \right) r$

$\frac{d\theta}{dt} = -\alpha_{\mathrm{max}} \left[\sin 2\theta - \sin 2\theta_{\mathrm{eq}} \right]$

where we have defined for brevity

$\alpha_{\mathrm{max}} \ \stackrel{\mathrm{def}}{=}\ \frac{f_{0} \omega_{n}^{2}}{4\omega_{p}}$

$\sin 2\theta_{\mathrm{eq}} \ \stackrel{\mathrm{def}}{=}\ \left( \frac{2}{f_{0}} \right) \epsilon$

and the detuning

$\epsilon \ \stackrel{\mathrm{def}}{=}\ \frac{\omega_{p}^{2} - \omega_{n}^{2}}{\omega_{n}^{2}}$

The $θ$ equation does not depend on $r$ , and linearization near its equilibrium position $θ eq$ shows that $θ$ decays exponentially to its equilibrium

$\theta(t) = \theta_{\mathrm{eq}} + \left( \theta_{0} - \theta_{\mathrm{eq}} \right) e^{-2\alpha t}$

where the decay constant

$\alpha \ \stackrel{\mathrm{def}}{=}\ \alpha_{\mathrm{max}} \cos 2\theta_{\mathrm{eq}}$ .

In other words, the parametric oscillator phase-locks to the pumping signal $f (t)$ .

Taking $θ(t) = θ eq$ (i.e., assuming that the phase has locked), the $r$ equation becomes

$\frac{dr}{dt} = \alpha r$

whose solution is $r (t) = r 0 e α t$ ; the amplitude of the $q (t)$ oscillation diverges exponentially. However, the corresponding amplitude $R (t)$ of the untransformed variable $x \ \stackrel{\mathrm{def}}{=}\ q e^{-D}$ need not diverge

R (t) = r (t) e - D = r 0 e α t - D

The amplitude $R (t)$ diverges, decays or stays constant, depending on whether $α t$ is greater than, less than, or equal to $D$ , respectively.

The maximum growth rate of the amplitude occurs when $ω p = ω n$ . At that frequency, the equilibrium phase $θ eq$ is zero, implying that $cos2θ eq = 1$ and $α = α max$ . As $ω p$ is varied from $ω n$ , $θ eq$ moves away from zero and $α < α max$ , i.e., the amplitude grows more slowly. For sufficiently large deviations of $ω p$ , the decay constant $α$ can become purely imaginary since

$\alpha = \alpha_{\mathrm{max}} \sqrt{1- \left( \frac{2}{f_{0}} \right)^{2} \epsilon^{2}}$

If the detuning $ε$ exceeds $f 0 / 2$ , $α$ becomes purely imaginary and $q (t)$ varies sinusoidally. Using the definition of the detuning $ε$ , the pumping frequency $2ω p$ must lie between $2\omega_{n} \sqrt{1 - \frac{f_{0}}{2}}$ and $2\omega_{n} \sqrt{1 + \frac{f_{0}}{2}}$ . Expanding the square roots in a binomial series shows that the spread in pumping frequencies that result in exponentially growing $q$ is approximately $ω n f 0$ .

[edit] Intuitive derivation of parametric excitation

The above derivation may seem like a mathematical sleight-of-hand, so it may be helpful to give an intuitive derivation. The $q$ equation may be written in the form

$\frac{d^{2}q}{dt^{2}} + \omega_{n}^{2} q = -\omega_{n}^{2} f(t) q$

which represents a simple harmonic oscillator (or, alternatively, a bandpass filter) being driven by a signal $-\omega_{n}^{2} f(t) q$ that is proportional to its response $q$ .

Assume that $q (t) = A cosω p t$ already has an oscillation at frequency $ω p$ and that the pumping $f (t) = f 0 sin2ω p t$ has double the frequency and a small amplitude $f_{0} \ll 1$ . Their product $q (t) f (t)$ produces two driving signals, one at frequency $ω p$ and the other at frequency $3ω p$

$f(t)q(t) = \frac{f_{0}}{2} A \left( \sin \omega_{p} t + \sin 3\omega_{p} t \right)$

Being off-resonance, the $3ω p$ signal is attentuated and can be neglected initially. By contrast, the $ω p$ signal is on resonance, serves to amplify $q$ and is proportional to the amplitude $A$ . Hence, the amplitude of $q$ grows exponentially unless it is initially zero.

Expressed in Fourier space, the multiplication $f (t) q (t)$ is a convolution of their Fourier transforms $\tilde{F}(\omega)$ and $\tilde{Q}(\omega)$ . The positive feedback arises because the $+ 2ω p$ component of $f (t)$ converts the $- ω p$ component of $q (t)$ into a driving signal at $+ ω p$ , and vice versa (reverse the signs). This explains why the pumping frequency must be near $2ω n$ , twice the natural frequency of the oscillator. Pumping at a grossly different frequency would not couple (i.e., provide mutual positive feedback) between the $- ω p$ and $+ ω p$ components of $q (t)$ .

[edit] Parametric amplifiers

A parametric amplifier is basically a mixer with gain. The mixer gain shows up as signal amplification. As a result the output frequency is not the same as the input frequency.

The parametric oscillator equation can be extended by adding an external driving force $E (t)$ :

$\frac{d^{2}x}{dt^{2}} + \beta(t) \frac{dx}{dt} + \omega^{2}(t) x = E(t).$

We assume that the damping $D$ is sufficiently strong that, in the absence of the driving force $E$ , the amplitude of the parametric oscillations does not diverge, i.e., that $α t < D$ . In this situation, the parametric pumping acts to lower the effective damping in the system. For illustration, let the damping be constant $β(t) = ω 0 b$ and assume that the external driving force is at the mean resonance frequency $ω 0$ , i.e., $E (t) = E 0 sinω 0 t$ . The equation becomes

$\frac{d^{2}x}{dt^{2}} + b \omega_{0} \frac{dx}{dt} + \omega_{0}^{2} \left[1 + h_{0} \sin 2\omega_{0} t \right] x = E_{0} \sin \omega_{0} t$

whose solution is roughly

$x(t) = \frac{2E_{0}}{\omega_{0}^{2} \left( 2b - h_{0} \right)} \cos \omega_{0} t.$

As $h 0$ approaches the threshold $2 b$ , the amplitude diverges. When $h \geq 2b$ , the system enters parametric resonance and the amplitude begins to grow exponentially, even in the absence of a driving force $E (t)$ .

[edit] Other relevant mathematical results

If the parameters of any second-order linear differential equation are varied periodically, Floquet analysis shows that the solutions must vary either sinusoidally or exponentially.

The $q$ equation above with periodically varying $f (t)$ is an example of a Hill equation. If $f (t)$ is a simple sinusoid, the equation is called a Mathieu equation.

[edit] Low noise

The reason parametric amplifiers were so popular was because of their low-noise^{[citation needed]}. A varying capacitor adds very little noise to a signal. Hence the Parametric amp was very low noise. Bob Pease wrote in EDN that the world's first commercially successful op-amp [the Philbrick P2 varactor bridge amplifier] used 4 varactor diodes in its input. No one could match their noise figure or low input current for a long time.

Parametric amplifiers have become obsolete with the advent of HEMTs and MESFETs. These are the devices of choice in modern Low-Noise amplifiers.

[edit] References

This article does not cite any references or sources. (May 2008)
Please help improve this article by adding citations to reliable sources. Unverifiable material may be challenged and removed.

[edit] Further reading

Faraday M. (1831) "On a peculiar class of acoustical figures; and on certain forms assumed by a group of particles upon vibrating elastic surfaces", Phil. Trans. Roy. Soc. (London), 121, 299-318.
Kühn L. (1914) Elektrotech. Z., 35, 816-819.
Melde F. (1859) "Über Erregung stehender Wellen eines fadenförmigen Körpers", Ann. Phys. Chem. (ser. 2), 109, 193-215.
Mumford WW. (1961) "Some Notes on the History of Parametric Transducers", Proc. IRE, 48, 848-853.
Pungs L. DRGM Nr. 588 822 (24 October 1913); DRP Nr. 281440 (1913); Elektrotech. Z., 44, 78-81 (1923?); Proc. IRE, 49, 378 (1961).
Strutt JW (Lord Rayleigh). (1883) "On Maintained Vibrations", Phil. Mag., 15, 229-235.
Strutt JW (Lord Rayleigh). (1887) "On the maintenance of vibrations by forces of double frequency, and on the propagation of waves through a medium endowed with periodic structure", Phil. Mag., 24, 145-159.
Strutt JW (Lord Rayleigh). (1945) The Theory of Sound, 2nd. ed., Dover.

Hidden categories: All articles with unsourced statements | Articles with unsourced statements since March 2008 | Articles lacking sources from May 2008 | All articles lacking sources

Parametric oscillator

From Wikipedia, the free encyclopedia

Contents

[edit] Overview

[edit] History

[edit] The mathematics

[edit] Transformation of the equation

[edit] Solution of the transformed equation

[edit] Intuitive derivation of parametric excitation

[edit] Parametric amplifiers

[edit] Other relevant mathematical results

[edit] Low noise

[edit] References

[edit] Further reading

[edit] See also

Views

Navigation

Interaction

Search

Languages