OTRAG Rocket
From Wikipedia, the free encyclopedia
The OTRAG rocket was a modular satellite-delivery rocket developed by the OTRAG company. The OTRAG rocket was to become a rocket built up from several mass-produced units, intended to carry satellites with a weight of 1-10 tons or more into orbit. Mass production meant that the vehicle was projected to have been 10x cheaper than conventional vehicles of similar capability.
[edit] Design
Various OTRAG rockets could be built up from the company's CRPUs (Common Rocket Propulsion Unit). A sounding rocket would bundle four or more CRPUs in parallel, topped with the payload. An orbital launcher would use dozens to hundreds of CRPUs, depending on payload mass. The launcher would then stage by dropping outer CRPUs, leaving the interior ones to continue with payload.
A CRPU was essentially a steel tube, 27 cm in diameter and 16 meters long, joined from a few shorter tubes. The CRPU was divided into three sections by aluminum bulkheads, with additional stiffening rings between bulkheads. Forward, the majority of the tube contained a mixture of nitric acid and nitrogen tetroxide oxidizers. Next was a section of kerosene fuel. This was commercial-grade kerosene, not the more expensive RP-1. Last was the engine section. A fuel line carried nitric acid around the kerosene, into the engine.
The design of the CRPU was extremely simple. The tubing was strong enough that the propellants were fed to the engine by pressure alone. This eliminated the need for turbopumps. The engine was ablatively cooled, eliminating the need for fine fuel passages and heat-resistant kerosene. The engine did not gimbal; instead, the vehicle was steered by throttling one side's CRPUs versus the opposite side. Thus, the engine was simply built into the tube walls, with the only mechanisms being the throttling valves. No separate pressurizing system was included; the tanks were simply left with an ullage space, which was then filled with gas to a few hundred psi. Because of the narrow tubing, the bulkheads between sections could be simple plates, instead of domes like virtually all other rocket stages. There was no ignition system; instead, a slug of furfuryl alcohol was injected before the kerosene. The furfuryl alcohol ignited spontaneously upon contact with the nitric acid.
The use of ablative cooling, high-pressure steel construction, and large "empty" spaces meant that a CRPU was heavy, with relatively low performance. The diameter of the tubing also put a hard limit on the engine diameter, preventing use of an efficient, high-expansion nozzle for the upper stages. However, ganging CRPUs into three stages was sufficient to reach orbit. Meanwhile, the low cost of each CRPU, after the economies of scale gained by producing hundreds or possibly thousands of them per year, would have still left the vehicle cheaper than its contemporaries. Additionally, the large number of small engines firing simultaneously would have given a high degree of reliability and a relatively smooth ride.
The company's baseline launcher design claimed to lift one metric ton to orbit. It would have consisted of a third stage core of four CRPUs, surrounded by a second stage of twelve CRPUs, in turn surrounded by the first stage's 48 CRPUs. Larger vehicles and capacities would be achieved with greater numbers of CRPUs, possibly including several hundred per flight for a heavy launcher.
The company forecasted that CRPUs would eventually be so cheap, recovering and refurbishing a launcher would be no better than simply building more units. The use of storable propellants and few moving parts meant that launch-site operations would also be very simple.
[edit] Flight History
The engines were tested extensively on ground rigs, on both German and African test sites. Experiments were run with varying fuel and oxidizer formulations, as the general design was quite robust.
Small, 4-unit vehicles were built and tested in Shaba North, Zaire and Seba Oasis, Libya, where heights of 20 to 50 kilometers were reached. The rockets used there were 6 and 12 meters long. The basic CRPU concept was shown to be workable, though some rockets experienced guidance or component failures. The last launch of an OTRAG rocket took place on September 19, 1983 in Esrange. Following this launch, the OTRAG rocket was to be used in high altitude research.
OTRAG seems to have been basically squelched by the American launch providers who were unwilling to see a competing launch provider, particularly a German launch provider emerge, and rumours were started that the project was weaponry related. This eventually killed the project.
After the company had left Libya, some remaining equipment was confiscated by the government. However, enough parts and knowledge were missing to prevent Libya from continuing the project.