Mobility management

From Wikipedia, the free encyclopedia

Mobile communication standards
GSM / UMTS (3GPP) Family
GSM (2G)
UMTS (3G)
UMTS Rev. 8 (Pre-4G)
CDMA (3GPP2) Family
cdmaOne (2G)
CDMA2000 (3G)
UMB (Pre-4G)
AMPS Family
AMPS (1G)
D-AMPS (2G)
Other Technologies
0G
1G
2G
Pre-4G
Channel Access Methods
Frequency bands

Mobility Management is one of the major functions of a GSM or a UMTS network that allows mobile phones to work. The aim of mobility management is to track where the subscribers are, so that calls, SMS and other mobile phone services can be delivered to them.

Contents

[edit] Location update procedure

A GSM or UMTS network, like all cellular networks, is a radio network of individual cells, known as base stations. Each base station covers a small geographical area which is part of a uniquely identified location area. By integrating the coverage of each of these base stations, a cellular network provides a radio coverage over a very much wider area. A group of base stations is called a location area, or a routing area.

The location update procedure allows a mobile device to inform the cellular network, whenever it moves from one location area to the next. Mobiles are responsible for detecting location area codes. When a mobile finds that the location area code is different from its last update, it performs another update by sending to the network, a location update request, together with its previous location, and its Temporary Mobile Subscriber Identity (TMSI).

There are several reasons why a mobile may provide updated location information to the network. Whenever a mobile is switched on or off, the network may require it to perform an IMSI attach or IMSI detach location update procedure. Also, each mobile is required to regularly report its location at a set time interval using a periodic location update procedure. Whenever a mobile moves from one location area to the next while not on a call, a random location update is required. This is also required of a stationary mobile that reselects coverage from a cell in a different location area, because of signal fade. Thus a subscriber has reliable access to the network and may be reached with a call, while enjoying the freedom of mobility within the whole coverage area.

When a subscriber is paged in an attempt to deliver a call or SMS and the subscriber does not reply to that page then the subscriber is marked as absent in both the MSC/VLR and the HLR (Mobile not reachable flag MNRF is set). The next time the mobile performs a location update the HLR is updated and the mobile not reachable flag is cleared.

[edit] TMSI

The "Temporary Mobile Subscriber Identity" (TMSI) is the identity that is most commonly sent between the mobile and the network. TMSI is randomly assigned by the VLR to every mobile in the area, the moment it is switched on. The number is local to a location area, and so it has to be updated, each time the mobile moves to a new geographical area.

The network can also change the TMSI of the mobile at any time. And it normally does so, in order to avoid the subscriber from being identified, and tracked by eavesdroppers on the radio interface. This makes it difficult to trace which mobile is which, except briefly, when the mobile is just switched on, or when the data in the mobile becomes invalid for one reason or another. At that point, the global "international mobile subscriber identity" (IMSI) must be sent to the network. This is a unique number that is associated with all GSM and UMTS network mobile phone users. The number is stored in the SIM card. The IMSI is sent as rarely as possible, to avoid it being identified and tracked.

A key use of the TMSI is in paging a mobile. "Paging" is the one-to-one communication between the mobile and the base station. The most important use of broadcast information is to set up channels for "paging". Every cellular system has a broadcast mechanism to distribute such information to a plurality of mobiles.

Size of TMSI is 4 octet with full hex digits and can't be all ones.

[edit] Roaming

Roaming is one of the fundamental mobility management procedures of all cellular networks. Roaming is defined (cf. GSM Association Permanent Reference Document AA.39) as the ability for a cellular customer to automatically make and receive voice calls, send and receive data, or access other services, including home data services, when travelling outside the geographical coverage area of the home network, by means of using a visited network. This can be done by using a communication terminal or else just by using the subscriber identity in the visited network. Roaming is technically supported by mobility management, authentication, authorization and billing procedures. To understand the details and technical aspects of roaming, please see the articles about roaming and GSM services: How incoming calls are made.

[edit] Location area

A "location area" is a set of base stations that are grouped together to optimise signalling. Typically, 10s or even 100s of base stations share a single Base Station Controller (BSC), the intelligence behind the base stations. The BSC handles allocation of radio channels, receives measurements from the mobile phones, controls handovers from base station to base station.

To each location area, a unique number called a "location area code" is assigned. The location area code is broadcast by each base station, known as a "base transceiver station" BTS in GSM, or a Node B in UMTS, at regular intervals.

In GSM, the mobiles cannot communicate directly with each other but, have to be channeled through the BTSs. In UMTS networks, if no Node B is accessible to a mobile, it will not be able to make any connections at all.

If the location areas are very large, there will be many mobiles operating simultaneously, resulting in very high paging traffic, as every paging request has to be broadcast to every base station in the location area. This wastes bandwidth and power on the mobile, by requiring it to listen for broadcast messages too much of the time. If on the other hand, there are too many small location areas, the mobile must contact the network very often for changes of location, which will also drain the mobile's battery. A balance has therefore to be struck.

[edit] Routing area

A "routing area" is a subdivision of a "location area". Routing areas are used by mobiles which are GPRS-attached. GPRS ("General Packet Radio Services"), GSM’s new data transmission technology, is optimized for "bursty" data communication services, such as wireless internet/intranet, and multimedia services. It is also known as GSM-IP ("Internet Protocol") because it will connect users directly to Internet Service Providers (ISP).

The bursty nature of packet traffic means that more paging messages are expected per mobile, and so it is worth knowing the location of the mobile more accurately than it would be with traditional circuit-switched traffic. A change from routing area to routing area (called a "Routing Area Update") is done in an almost identical way to a change from location area to location area. The main differences are that the "Serving GPRS Support Node" (SGSN) is the element involved.


[edit] See also

[edit] External links

 This article or section includes a list of references or external links, but its sources remain unclear because it lacks in-text citations.
You can improve this article by introducing more precise citations.