Longcase clock

From Wikipedia, the free encyclopedia

A longcase clock with a pine case, c. 1790, by Thomas Ross of Hull. The two keyholes on either side of the dial show this to be an eight-day clock.
A longcase clock with a pine case, c. 1790, by Thomas Ross of Hull. The two keyholes on either side of the dial show this to be an eight-day clock.
 This article does not cite any references or sources. (May 2008)
Please help improve this article by adding citations to reliable sources. Unverifiable material may be challenged and removed.

A longcase clock, also tall-case clock, grandfather clock or floor clock, is a freestanding, weight-driven, pendulum clock with the pendulum held inside the tower, or waist of the case. Clocks of this style are commonly around 1.8-2.4m (6-8 feet) tall. The case often features elaborately carved ornamentation on the hood, or bonnet, which surrounds and frames the dial, or clock face. The English clockmaker William Clement is credited with the development of this form in 1670. Most longcase clocks are striking clocks, which means they sound the time on each hour or fraction of an hour.

The terms "grandfather", "grandmother", and "granddaughter" have been applied to longcase clocks. Although there is no specifically defined difference among these terms, the general perception seems to be that a clock smaller than 1.5m (5 feet) is a granddaughter; over 1.5m (5 feet) is a grandmother; and over 1.8m (6 feet) is a grandfather.

Contents

[edit] Origin

Cross section of a longcase clock movement without striking mechanism, mid-1800s.
Cross section of a longcase clock movement without striking mechanism, mid-1800s.

The advent of the longcase clock is due to the invention of the anchor escapement mechanism around 1670. Prior to that, pendulum clock movements used an older verge escapement mechanism, which required very wide pendulum swings of about 100°. Long pendulums with such wide swings could not be fitted within a case, so most clocks had short pendulums. The anchor mechanism reduced the pendulum's swing to around 4° to 6°, allowing clockmakers to use longer pendulums, which had slower "beats". These needed less power to keep going, caused less friction and wear in the movement, and were more accurate. Most longcase clocks use a "seconds" (or "Royal") pendulum, meaning that each swing takes one second. These are about a metre (39 inches) long (to the centre of the bob). This requirement for height, along with the need for a long drop space for the weights which power the clock, gave rise to the design of the long narrow case.

Modern longcase clocks use a more accurate variation of the anchor escapement called the deadbeat escapement.

[edit] Description

Most of a longcase clock's height is used to hold the long pendulum and weights. The two chains attached to the weights and the lack of winding holes in the dial show this to be a thirty-hour clock.
Most of a longcase clock's height is used to hold the long pendulum and weights. The two chains attached to the weights and the lack of winding holes in the dial show this to be a thirty-hour clock.

Traditionally, longcase clocks were made with two types of movement: eight-day movements and 30-hour movements. A clock with an eight-day movement required winding only once a week, while the generally lower-priced 30-hour clock had to be wound every day. Eight-day clocks are often driven by two weights - one driving the pendulum and the other the striking mechanism, which usually consisted of a bell or chimes. Such movements usually have two keyholes on either side of the dial to wind each one (as can be seen in the Thomas Ross clock above). By contrast, 30-hour clocks often had a single weight to drive both the pendulum and the chimes. Some 30-hour clocks were made with false keyholes, for customers who wished that guests to their home would think that the household was able to afford the more expensive eight-day clock. All modern chiming grandfather clocks have 8-day movements. Most grandfather clocks are cable-driven, meaning that the weights are suspended by cables. If the cable was attached directly to the weight, the load would cause rotation and untwist the cable strands, so the cable wraps around a pulley mounted to the top of each weight. The mechanical advantage of this arrangement also doubles the running time allowed by a given weight drop.

Cable clocks are wound by inserting a special crank (called a "key") into holes in the clock's face and turning it. Others, however, are chain-driven, meaning that the weights are suspended by chains that wrap around gears in the clock's mechanism, with the other end of the chain hanging down next to the weight. To wind a chain-driven grandfather clock, one pulls on the end of each chain, lifting the weights until the weights come up to just under the clock's face.

[edit] Elaborate striking sequences

In the early 20th century, quarter-hour chime sequences were added to grandfather clocks. At the top of each hour, the full chime sequence sounds, immediately followed by the hour strike. At 15 minutes after each hour, 1/4 of the chime sequence plays, at the bottom of each hour, half of the chime sequence plays, and at 15 minutes before each hour, 3/4 of the chime sequence plays. Almost all modern mechanical grandfather clocks have at least Westminster Quarters, and many also offer the option of Whittington chimes or St. Michael's chimes, selectable by a switch mounted on the right side of the dial, which also allows one to silence the chimes if desired. As a result of adding chime sequences, all modern mechanical grandfather clocks have three weights instead of just two. The left weight provides power for the hour strike, the middle weight provides power for the clock's pendulum and general timekeeping functions, while the right weight provides power for the quarter-hour chime sequences.

[edit] The origin of the term "grandfather clock"

During the 19th century, two brothers named Jenkins worked as managers at the George Hotel in Piercebridge, County Durham, England. One of the brothers died and, according to the story told to Henry Clay Work in 1875, the clock (made by James Thompson) began to lose time. Repair attempts were made, but failed. When the other brother died at the age of 90, the clock stopped running altogether, and was never repaired in remembrance of the brothers.

Work decided to write a song about the story of this clock, which he called My Grandfather's Clock. The song became popular, and it is from this song that the current usage derives. [1]

[edit] Types of longcase clock

Comtoise clock
Comtoise clock
Bornholm clock
Bornholm clock

[edit] Comtoise clocks

Comtoise clocks, also known as Morbier clocks or Morez clocks, were made in the French region Franche-Comté (whence their name). Production of these clocks began in 1680 and continued for a period of about 230 years. During the peak production years (1850-1890) over 60,000 clocks were made each year.

Many Comtoise clocks can be found in France but they are also frequently found in Spain, Germany, and other parts of Europe, less in the USA. These clocks were very popular across the generations; they kept the time on farms throughout France. Many Comtoise clocks were also exported to other countries in Europe and even further, to the Ottoman Empire and as far as Thailand. The metal mechanism was usually protected by a wooden sheath.

[edit] Bornholm clocks

Bornholm clocks are Danish longcase clocks in the form of a tall wooden box. They are driven by a pendulum and were made on Bornholm from 1745 to 1900.

Bornholm clock-making began in the 1740s when an English ship, which had longcase clocks in its hold, was stranded. They were sent for repair to a turner named Poul Ottesen Arboe in Rønne and as a result of his repair of them he learned enough about clocks to begin to make his own.

The demand for Bornholm clocks has been falling in recent years.

[edit] Historical manufacturers

Clockmakers in England

Clockmakers in Scotland

Clockmakers in Wales

Clockmakers in the United States

[edit] Current manufacturers

Bulova Watch Company

[edit] External links