LC-3

From Wikipedia, the free encyclopedia

The Little Computer 3, or LC-3, comprises an assembly language that is most often used to teach fundamentals of programming and computer architecture to computer science and computer engineering students. The LC-3 language features a relatively simple instruction set, but it can be used to write moderately complex assembly programs and is a theoretically viable target for a C compiler. These features make the assembly language useful for beginning instruction, as it is less complex than x86 assembly but has many features similar to those in more complex languages.

The LC-3 was developed by Yale N. Patt at the University of Texas at Austin and Sanjay J. Patel at the University of Illinois at Urbana-Champaign. Their specification of the instruction set, the overall architecture of the LC-3, and a hardware implementation can be found in the second edition of their textbook, Introduction to Computing Systems: From Bits and Gates to C and Beyond. Courses based on the LC-3 and Patt and Patel's book are offered in many computer engineering and computer science departments.

Contents 1 Architectural specification 2 Instruction set 3 Programming language support 3.1 C and the LC-3 4 The LC-3b

[edit] Architectural specification

The LC-3 specifies a word size of 16 bits for its registers and uses a 16-bit addressable memory with a 2¹⁶-location address space. The register file contains eight registers, referred to by number as R0 through R7. All of the registers are general-purpose in that they may be freely used by any of the instructions that can write to the register file, but in some contexts (such as translating from C code to LC-3 assembly) some of the registers are used for special purposes.

Instructions are 16 bits wide and have 4-bit opcodes. The instruction set defines instructions for fifteen of the sixteen possible opcodes, though some instructions have more than one mode of operation. Individual instructions' execution is regulated by a state machine implemented with a control ROM and microsequencing unit.

The architecture supports the use of a keyboard and monitor to regulate input and output; this support is provided through memory mapped I/O abstractions. In simulation, these registers can be accessed directly, and the architectural specification describes their contents. Higher-level I/O support is also provided through the use of the TRAP instruction and a basic operating system. The operating system provides functions to read and echo characters from the keyboard, print individual characters to the monitor, print entire strings in both packed and unpacked forms, and halt the machine.

All data in the LC-3 is assumed to be stored in a two's complement representation; there is no separate support for unsigned arithmetic. The I/O devices operate on ASCII characters. The LC-3 has no native support for floating-point numbers.

The hardware implementation given in the Patt and Patel text is not pipelined or otherwise optimized, but it is certainly possible to create a fast implementation using more advanced concepts in computer architecture.

[edit] Instruction set

The LC-3 instruction set implements fifteen types of instructions, with a sixteenth opcode reserved for later use. The architecture is a load-store architecture; values in memory must be brought into the register file before they can be operated upon.

Arithmetic instructions available include addition, bitwise AND, and bitwise NOT, with the first two of these able to use both registers and sign-extended immediate values as operands. These operations are sufficient to implement a number of basic arithmetic operations, including subtraction (by negating values) and bitwise left shift (by using the addition instruction to multiply values by two). The LC-3 can also implement any bitwise logical function, owing to the fact that NOT and AND together are logically complete.

Memory accesses can be performed by computing addresses based on the current value of the program counter (PC) or a register in the register file; additionally, the LC-3 provides indirect loads and stores, which use a piece of data in memory as an address to load data from or store data to. Values in memory must be brought into the register file before they can be used as part of an arithmetic or logical operation.

The LC-3 provides both conditional and unconditional control flow instructions. Conditional branches are based on the arithmetic sign (negative, zero, or positive) of the last piece of data written into the register file. Unconditional branches may move execution to a location given by a register value or a PC-relative offset. Three instructions (JSR, JSRR, and TRAP) support the notion of subroutine calls by storing the address of the code calling the subroutine into a register before changing the value of the program counter. The LC-3 does not support the direct arithmetic comparison of two values; comparing two register values arithmetically requires subtracting one from the other and evaluating the result.

[edit] Programming language support

While it has not been implemented on a physical chip, the LC-3 can be used in simulation on both Linux/Unix and Windows environments. The simulation tools include an assembler with support for computerized offset computation with labels and the insertion of constants, strings, and blank memory locations into a block of assembly code. There is also a convention for using the C programming language on the LC-3. A sample assembler, compiler, and simulator are provided by McGraw-Hill.

[edit] C and the LC-3

The calling convention for C functions on the LC-3 is similar to that implemented by other systems, such as the x86 ISA. When running C programs, the architecture maintains a memory model that includes space for a call stack and dynamic memory allocation. In this model, four of the processor's eight general purpose registers take on special roles: R4 is used as a base register for loading and storing global data, R5 is used to point to the current function's area on the call stack, and R6 is used as a stack pointer. Additionally, R7 is usually reserved for storage of return addresses from function calls; the JSR, JSRR, and TRAP instructions automatically store return addresses in this register during their execution.

When a C function is called under this model, the function's parameters are pushed onto the stack right to left. Space is then made on the stack for the return value of the function being called, the address of the instruction in the caller to return to, and the caller's value of R5. Local variables in the function being called are pushed onto the stack in the order that they are declared. Note that the LC-3 does not have native PUSH and POP instructions, so addition and memory storage instructions must be used separately to implement the stack.

[edit] The LC-3b

The LC-3b ISA describes a modified version of the LC-3 that includes the following changes:

• The machine's word size remains 16 bits, but its memory is now byte-addressable with the same address space.
• The LD and ST instructions (load and store data using PC-relative addressing) have been removed.
• The LDI and STI instructions (indirect loads and stores) use register-based addressing instead of PC-relative addressing.
• Two instructions, LDB and STB, have been added to manipulate individual bytes of memory; the other load and store instructions continue to act on entire words.
• The reserved opcode has been converted into a shift instruction, SHF, that supports arithmetic and logical shifts of arbitrary size in both directions.

These changes make the hardware of the LC-3b slightly more complicated than that of the LC-3 (for example, the LC-3b requires a shifter while the LC-3 does not, and the LC-3b requires extra logic in its memory unit to properly handle loading and storing of data of various sizes).

Ashley Wise maintains a set of tools for simulating and working with the LC-3b.