Jetboat
From Wikipedia, the free encyclopedia
A jetboat is a boat propelled by a jet of water ejected from the back of the craft. Unlike a powerboat or motorboat that uses a propeller in the water below or behind the boat, a jetboat draws the water from under the boat into a pump-jet inside the boat, then expels it through a nozzle at the stern.
Jetboats were originally designed by Sir William Hamilton (who developed a waterjet in 1954) for operation in the fast-flowing and shallow rivers of New Zealand, specifically to overcome the problem of propellers striking rocks in such waters.
Previous attempts at waterjet propulsion had very short lifetimes, generally due to the inefficient design of the units and the fact that they offered few advantages over conventional propellers. Unlike these previous waterjet developments, such as Campini's and the Hanley Hydrojet, Hamilton had a specific need for a propulsion system to operate in very shallow water, and the waterjet proved to be the ideal solution. From this the popularity of the jet unit and jetboat increased rapidly, and through further developments it was found the waterjet offered several other advantages over propellers for a wide range of vessel types, and as such waterjets are used widely today for many high speed vessels including passenger ferries, rescue craft, patrol boats and offshore supply vessels.
Jet boats are highly maneuverable, and many can, from full speed, be reversed and brought to a stop within little more than their own length, in a maneuver known as a "crash stop". The well known Hamilton turn or "jet spin" is a high speed manoevre where the boat is turned sharply then the engine throttle is cut causing the boat's stern to lift and spin quickly around with a large spray of water.
There is no engineering limit to the size of jet boats, though the validity of their use depends a lot on the type of application. Classic prop-drives are generally more efficient and economical at low speeds (up to about 20 knots) but as boat speed increases beyond this the extra hull resistance generated by struts, rudders, shafts etc means waterjets are more efficient in the 20-50 knot range. Also, in situations where you need very large propellers turning at slow speeds (such as tug boats) the equivalent size waterjet would be simply too big to be practical. For these reasons the vast majority of waterjet units are installed in high speed vessels and in particular situations where shallow draught, manoeuvrability and load flexibility are main concerns.
The biggest jet-driven vessels are found in military use or the high speed passenger/car ferry industry. South Africa's Valour class frigates (approximately 120m long) are the biggest jet-propelled vessels so far. Even these German-built vessels are capable of performing "crash stops.
Contents |
[edit] How jet boats work
A conventional screw propeller works within the body of water below a boat hull, effectively "screwing" through the water to drive a vessel forward by generating a difference in pressure between the forward and rear surfaces of the propeller blades and by accelerating a mass of water rearward. By contrast a waterjet unit delivers a high pressure "push" out the stern of a vessel by accelerating a volume of water as it passes through a specialised pump mounted above the waterline inside the boat hull. Both methods yield thrust due to Newton's third law — every action has an equal and opposite reaction.
In a jetboat, the waterjet draws water from beneath the hull where it passes through a series of impellers and stators - known as stages - which increase the velocity of the waterflow. Most modern jets are single stage while older waterjets may have as many as three stages. The tail section of the waterjet unit extends out through the transom of the hull above the waterline. This jetstream exits the unit through a small nozzle at high velocity to push the boat forward. Steering is accomplished by moving this nozzle to either side, or less commonly, by small gates on either side that direct the jetstream. Because the jet boat relies on the flow of water through the nozzle for control, it is not possible to steer a conventional jet boat without the throttle open.
Unlike conventional propeller systems where the rotation of the propeller is reverse to provide astern movement, a waterjet will continue to pump normally while a deflector is lowered into the jetstream after it leaves the outlet nozzle. This deflector redirects thrust forces forward to provide reverse thrust. Most highly developed reverse deflectors redirect the jetstream down and to each side to prevent recirculation of the water through the jet again - which may cause aeration problems - and increase reverse thrust. Steering is still available with the reverse deflector lowered so the vessel will have full manoeuvrability. With the deflector lowered about halfway into the jetstream, forward and reverse thrust are equal so the boat maintains a fixed position, but steering is still available to allow the vessel to turn on the spot - something which is impossible with a conventional single propeller.
Unlike hydrofoils, which use underwater wings or struts to lift the vessel clear of the water, standard jetboats use a conventional planing hull to ride across the water surface, with only the rear portion of the hull displacing any water. With the majority of the hull clear of the water, there is reduced drag, greatly enhancing speed and maneuverability, so jetboats are normally operated at planing speed. At slower speeds with less water pumping through the jet unit, the jetboat will lose some steering control and maneuverability and will quickly slow down as the hull comes off its planing state and hull resistance is increased. However, loss of steering control at low speeds can be negated by lowering the reverse deflector slightly and increasing throttle - so you increase thrust and thus control without increasing boat speed itself. A conventional river-going jet boat will have a shallow-angled (but not flat-bottomed) hull to improve its high speed cornering control and stability while also allowing it to traverse very shallow water. At speed, jetboats can be safely operated in less than 3 inches to (7.5 cm) of water.
One of the most significant breakthroughs in the development of the waterjet was to change the design so it expelled the jetstream above the water line, contrary to many people's intuition. Hamilton discovered early on that this greatly improved performance, compared to expelling below the waterline, while also providing a "clean" hull bottom (ie: nothing protruding below the hull line) to allow the boat to skim through very shallow water. It makes no difference to the amount of thrust generated whether the outlet is above or below the waterline, but being above the waterline reduces hull resistance and draught. Hamilton's first waterjet design had the outlet below the hull and actually in front of the inlet. This probably meant that disturbed water was entering the jet unit and reducing its performance, and the main reason why the change to above the waterline made such a difference.
Queenstown, New Zealand, where jetboats are used extensively for adventure tourism, claims to be the jetboat capital of the world.
[edit] Manufacturers
- Cabora builds lightweight, high-powered jetdrive inflatables also known as BlowBoats.
- Ultimate Boats builds all aluminum center console jet boats.
- Thunderjet builds lightweight, aluminum jet boats.
- SugarSand builds great recreational jetboats.
- Westend marine, Wakefield Uk.http://www.westendmarine.co.uk/
- The New Zealand company Hamilton Jet designs and builds jetboats and manufactures the large range of "HamiltonJet waterjet units" which are widely used around the world. Jetboats owned by private citizens are normally powered by one or two V8 petrol engines.
- [1] Sword Marine
- Bombardier of Canada makes many models of both jetboats and personal water craft (PWCs).
- Yamaha makes many models of both jetboats and personal water craft (PWCs).
- Sea Doo makes many models of both jetboats and personal water craft (PWCs).
[edit] Applications
Applications for jetboats include most activities where conventional propellers are also used, but in particular passenger ferry services, coastguard and police patrol, navy and military, adventure tourism (which is becoming increasingly popular around the globe), pilot boat operations, surf rescue, farming, fishing, exploration, pleasure boating, and other water activities where motor boats are used. Jetboats can also be raced for sport, both on rivers and on specially designed racecourses. Many jetboats are small enough to be carried on a trailer and towed by car. Recently there has been increasing use of jetboats in the form of rigid-hulled inflatable boats and as luxury yacht tenders.
One very important feature of the jetboat is the fact that it has no external rotating parts; it is essentially safe for swimmers and marine life, excluding being struck by the hull. This in itself can be reason enough to use this type of propulsion.
In 1977 Sir Edmund Hillary led a jetboat expedition, titled "Ocean to Sky", from the mouth of the Ganges River to its source. One of the jetboats was sunk by a friend of Hilary. [2]
[edit] Notes
- ^ Insert footnote text here
- ^ Edmund Hillary: From the Ocean to the Sky: Jet Boating Up the Ganges Ulverscroft Large Print Books Ltd (November 1980) ISBN 0-7089-0587-0
