Template:Infobox Connector/doc
From Wikipedia, the free encyclopedia
D4 Video connector | ||||
---|---|---|---|---|
|
||||
Type | Analogue video connector | |||
Production history | ||||
Designer | Some guy | |||
Designed | Early 1990s | |||
Manufacturer | Initially Toshiba | |||
Produced | Early 1990s to 2005 | |||
Superseded | RF connector | |||
Superseded by | DVI connector (2005) | |||
Specifications | ||||
Length | 36 mm (typical) | |||
Width | 25 mm | |||
Height | 6.5 mm | |||
Hot pluggable | Yes | |||
External | External | |||
Electrical | 220 volts AC 50 Hz typically | |||
Earth | Dedicate pin | |||
Max voltage | 450 volts peak | |||
Max current | 20 amps at 220 volts, 5 amps at 400 volts | |||
Audio signal | None | |||
Video signal | Analogue 480i, 480p, 720p, 1080i | |||
Data signal | Resolution and Aspect ratio only | |||
Width | 2 bits | |||
Bandwidth | 120 bps | |||
Max devices | 1 | |||
Protocol | Serial | |||
Cable | 14 core shielded (25 m max) | |||
Pins | 14 (6 video, 3 reserved, 2 detect, 3 data) | |||
Connector | DB-25 | |||
Pin out | ||||
A male connector seen from the front. |
||||
Spec name | Example col title | |||
Pin 1 | Y | luminance (0.7 V, 75 Ω) | ||
Pin 2 | Y GND | Y ground | ||
Pin 3 | Pb | 0.35 V, 75 Ω | ||
Pin 4 | Pb GND | |||
Pin 5 | Pr | 0.35 V, 75 Ω | ||
Pin 6 | Pr GND | |||
Pin 7 | Reserve link 1 | |||
Pin 8 | Data line 1 | 0V = 525 lines 2.2 V = 750 lines 5V = 1125 lines |
||
Pin 9 | Data line 2 | 0V = 59.94i / 60i 5 V = 59.94p / 60p |
||
Pin 10 | Reserve link 2 | |||
Pin 11 | Data line 3 | 0V = 4:3 2.2V = 4:3 letterbox 5V = 16:9 |
||
Pin 12 | Plug insert detect ground | |||
Pin 13 | Reserve link 3 | |||
Pin 14 | Plug insert detect | output 10 kΩ, input > 100 kΩ | ||
Hooks | GND | Shell ground | ||
These are some notes about the pinout of this connector. The pins are razor sharp. |
Connector Infobox is an infobox for electrical and (audio/video) signal connectors of all kinds.
[edit] Notes
The template supports 3 images:
- image, logo, pinout_image
Image and logo share a 300px wide area - so if both are used then the width of the image should be set to 150px i.e. [[Image:example.jpg|150px]]. If only image and pinout are used, then the size of both should be 300px.
[edit] Parameters and usage
{{Infobox connector |name= |type= |image= |logo= |caption= |designer= |design_date= |manufacturer= |production_date= |superseded= |superseded_by= |superseded_by_date= |external= |hotplug= |length= |width= |height= |electrical= |ground= |maximum_voltage= |maximum_current= |audio_signal= |video_signal= |data_signal= |data_bit_width= |data_bandwidth= |data_devices= |data_style= |cable= |physical_connector= |num_pins= |pinout_col1_name= |pinout_col2_name= |pinout_image= |pinout_caption= |pin1= |pin1_name= |pin2= |pin2_name= |pin3= |pin3_name= |pin4= |pin4_name= |pin5= |pin5_name= |pin6= |pin6_name= |pin7= |pin7_name= |pin8= |pin8_name= |pin9= |pin9_name= |pin10= |pin10_name= |pin11= |pin11_name= |pin12= |pin12_name= |pin13= |pin13_name= |pin14= |pin14_name= |pin15= |pin15_name= |pin16= |pin16_name= |pin17= |pin17_name= |pin18= |pin18_name= |pin19= |pin19_name= |pin20= |pin20_name= |pin21= |pin21_name= |pin22= |pin22_name= |pin23= |pin23_name= |pin24= |pin24_name= |pin25= |pin25_name= |pin26= |pin26_name= |pin27= |pin27_name= |pin28= |pin28_name= |pin29= |pin29_name= |pin30= |pin30_name= |pin31= |pin31_name= |pin_custom1_name= |pin_name_custom1= |pin_custom1= |pin_custom2_name= |pin_name_custom2= |pin_custom2= |pin_custom3_name= |pin_name_custom3= |pin_custom3= |pin_custom4_name= |pin_name_custom4= |pin_custom4= |pin_custom5_name= |pin_name_custom5= |pin_custom5= |pin_custom6_name= |pin_name_custom6= |pin_custom6= |pin_custom7_name= |pin_name_custom7= |pin_custom7= |pin_custom8_name= |pin_name_custom8= |pin_custom8= |pinout_notes= }}