Fluorescence lifetime imaging

From Wikipedia, the free encyclopedia

Fluorescence lifetime imaging or FLIM is a powerful tool for producing an image based on the differences in the exponential decay rate of the fluorescence from a fluorescent sample. It can be used as an imaging technique in confocal microscopy and other microscope systems.

The lifetime of the fluorophore signal, rather than its intensity, is used to create the image in FLIM. This has the advantage of minimizing the effect of photon scattering in thick layers of sample. FLIM is very useful for biomedical tissue imaging, allowing to probe greater tissue depths than conventional fluorescence microscopy.

1 Fluorescence lifetimes
2 Measurement and processing
- 2.1 Pulsed illumination
- 2.2 Phase modulation
3 References
4 External links

[edit] Fluorescence lifetimes

A fluorophore which is excited by a photon will drop to the ground state with a certain probability based on the decay rates through a number of different (radiative and/or nonradiative) decay pathways. To observe fluorescence, one of these pathways must be by spontaneous emission of a photon. In the ensemble description, the fluorescence emitted will decay with time according to

F (t) = F 0 e - t / τ

where

$\frac{1}{\tau} = \sum_fwfi k_i$ .

In the above, $t$ is time, $τ$ is the fluorescence lifetime, $F 0$ is the initial fluorescence at $t = 0$ , and $k i$ are the rates for each decay pathway, at least one of which must be the fluorescence decay rate $k f$ . More importantly, the lifetime, $τ$ , is independent of the initial intensity of the emitted light. This can be utilized for making non-intensity based measurements in chemical sensing.

[edit] Measurement and processing

Fluorescence lifetime imaging yields images with the intensity of each pixel determined by $τ$ , which allows one to view contrast between materials with different fluorescence decay rates (even if those materials fluoresce at the exact same wavelength), and also produces images which show changes in other decay pathways, such as in FRET imaging.

[edit] Pulsed illumination

Fluorescence lifetimes can be determined in the time domain by using a pulsed source. Time-correlated single photon counting (TCSPC) is usually employed because variations in source intensity and photoelectron amplitudes are ignored, the time resolution can be upwards of 4 ps, and the data obeys Poisson statistics (useful in determining goodness of fit during reconvolution).

When a population of fluorophores is excited by an ultrashort or delta pulse of light, the time-resolved fluorescence will decay exponentially as described above. However, if the excitation pulse or detection response is wide, the measured fluorescence, M(t), will not be purely exponential. The instrumental response function, IRF(t) will be convolved or blended with the decay function, F(t).

${M}(t) = {IRF}(t) \otimes {F}(t)$

The decay function (and corresponding lifetimes) cannot be recovered by direct deconvolution using Fourier transforms because division by zero will produce errors and noise will be amplified. However, the instrumental response of the source, detector, and electronics can be measured, usually from scattered excitation light. The IRF can then be convolved with a trial decay function to produce a calculated fluorescence, which can be compared to the measured fluorescence. The parameters for the trial decay function can be varied until the calculated and measured fluorescence curves fit well. This process is known as reconvolution or reiterative convolution, and can be performed quickly by several software packages.

[edit] Phase modulation

Alternatively, fluorescence lifetimes can be determined in the frequency domain by a phase-modulated method. The intensity of a continuous wave source is modulated at high frequencey, by an acousto-optic modulator for example, which will modulate the fluorescence. Since the excited state has a lifetime, the fluorescence will be delayed with respect to the excitation signal, and the lifetime can be determined from the phase shift. Also, y-components to the excitation and fluorescence sine waves will be modulated, and lifetime can be determined from the modulation ratio of these y-components. Hence, 2 values for the lifetime can be determined from the phase-modulation method.