Fiber to the premises

From Wikipedia, the free encyclopedia

It has been suggested that this article or section be merged into Fiber to the x. (Discuss)

Fiber to the premises (FTTP) is a form of fiber-optic communication delivery in which an optical fiber is run directly onto the customers' premises. This contrasts with other fiber-optic communication delivery strategies such as fiber to the node (FTTN), fiber to the curb (FTTC), or hybrid fibre-coaxial (HFC), all of which depend upon more traditional methods such as copper wires or coaxial cable for "last mile" delivery.

Fiber to the premises can be further categorized according to where the optical fiber ends:

• FTTH (fiber to the home) is a form of fiber optic communication delivery in which the optical signal reaches the end user's living or office space.^[1]

• An optical signal is distributed from the central office over an optical distribution network (ODN). At the endpoints of this network, devices called optical network terminals (ONTs) convert the optical signal into an electrical signal. (For FTTP architectures, these ONTs are located on private property.) The signal usually travels electrically between the ONT and the end-users' devices.

[edit] Optical portion

Optical distribution networks have several competing technologies.

[edit] Direct fiber

The simplest optical distribution network can be called direct fiber. In this architecture, each fiber leaving the central office goes to exactly one customer. Such networks can provide excellent bandwidth since each customer gets their own dedicated fiber extending all the way to the central office. However, this approach is extremely costly due to the amount of fiber and central office machinery required. It is usually used only in instances where the service area is very small and close to the central office.

[edit] Shared fiber

More commonly each fiber leaving the central office is actually shared by many customers. It is not until such a fiber gets relatively close to the customers that it is split into individual customer-specific fibers. There are two competing optical distribution network architectures which achieve this split: active optical networks (AONs) and passive optical networks (PONs)..

[edit] Active optical network

Comparison showing how a typical active optical network handles downstream traffic differently than a typical passive optical network. The type of active optical network shown is a star network capable of multicasting. The type of passive optical network shown is a star network having multiple splitters housed in the same cabinet.

Active optical networks rely on some sort of electrically powered equipment to distribute the signal, such as a switch, router, or multiplexer. Each signal leaving the central office is directed only to the customer for which it is intended. Incoming signals from the customers avoid colliding at the intersection because the powered equipment there provides buffering.

As of 2007, the most common type of active optical networks are called active ethernet, a type of ethernet in the first mile (EFM). Active ethernet uses optical ethernet switches to distribute the signal, thus incorporating the customers' premises and the central office into one giant switched ethernet network. Such networks are identical to the ethernet computer networks used in businesses and academic institutions, except that their purpose is to connect homes and buildings to a central office rather than to connect computers and printers within a campus. Each switching cabinet can handle up to 1,000 customers, although 400-500 is more typical. This neighborhood equipment performs layer 2/layer 3 switching and routing, offloading full layer 3 routing to the carrier's central office. The IEEE 802.3ah standard enables service providers to deliver up to 100 Mbit/s full-duplex over one single-mode optical fiber to the premises depending on the provider.

[edit] Passive optical network

It has been suggested that this article or section be merged into Passive optical network. (Discuss)

Passive optical networks do not use electrically powered components to split the signal. Instead, the signal is distributed using beam splitters. Each splitter typically splits a fiber into 16, 32, or 64 fibers, depending on the manufacturer, and several splitters can be aggregated in a single cabinet. A beam splitter cannot provide any switching or buffering capabilities; the resulting connection is called a point-to-multipoint link. For such a connection, the optical network terminals on the customer's end must perform some special functions which would not otherwise be required. For example, due to the absence of switching capabilities, each signal leaving the central office must be broadcast to all users served by that splitter (including to those for whom the signal is not intended). It is therefore up to the optical network terminal to filter out any signals intended for other customers. In addition, since beam splitters cannot perform buffering, each individual optical network terminal must be coordinated in a multiplexing scheme to prevent signals leaving the customer from colliding at the intersection. Two types of multiplexing are possible for achieving this: wavelength-division multiplexing and time-division multiplexing. With wavelength-division multiplexing, each customer transmits their signal using a unique wavelength. With time-division multiplexing, the customers "take turns" transmitting information. As of early 2007, only time-division multiplexing was technologically practical.

In comparison with active optical networks, passive optical networks have significant advantages and disadvantages. They avoid the complexities involved in keeping electronic equipment operating outdoors. They also allow for analog broadcasts, which can simplify the delivery of analog television. However, because each signal must be pushed out to everyone served by the splitter (rather than to just a single switching device), the central office must be equipped with a particularly powerful piece of transmitting equipment called an optical line terminal (OLT). In addition, because each customer's optical network terminal must transmit all the way to the central office (rather than to just the nearest switching device), customers can't be as far from the central office as is possible with active optical networks.

[edit] Electrical portion

Once on private property, the signal typically travels the final distance to the end user's equipment using an electrical format.

A device called an optical network terminal (ONT), also called an optical network unit (ONU), converts the optical signal into an electrical signal. (ONT is an ITU-T term, whereas ONU is an IEEE term, but the two terms mean exactly the same thing.) Optical network terminals require electrical power for their operation, so some providers connect them to back-up batteries in case of power outages. Optical network units use thin film filter technology (or more recently dispersion bridge planar lightwave circuit technology) to convert between optical and electrical signals.

For fiber to the home and for some forms of fiber to the building, it is common for the building's existing phone systems, local area networks, and cable TV systems to connect directly to the ONT.

If all three systems cannot directly reach the ONT, it is possible to combine signals and transport them over a common medium. Once closer to the end-user, equipment such as a router, modem, and/or network interface module can separate the signals and convert them into the appropriate protocol. For example, one solution for apartment buildings uses VDSL to combine data (and / or video) with voice. With this approach, the combined signal travels through the building over the existing telephone wiring until it reaches the end-user's living space. Once there, a VDSL modem copies the data and video signals and converts them into ethernet protocol. These are then sent over the end user's category 5 cable. A network interface module can then separate out the video signal and convert it into an RF signal that is sent over the end-user's coaxial cable. The voice signal continues to travel over the phone wiring and is sent through DSL filters to remove the video and data signals. An alternative strategy allows data and / or voice to be transmitted over coaxial cable. In yet another strategy, some office buildings dispense with the telephone wiring altogether, instead using voice over IP phones that can plug directly into the local area network.

[edit] Deployment history

Main article: Fiber to the premises by country

[edit] See also

• Fiber-optic communication
• Fiber to the x
• Hybrid fibre-coaxial

[edit] References

[edit] External links

• Fiber to the Home Council: Asia & The Pacific
• Fiber to the Home Council: Europe
• Fiber to the Home Council: Northern America
• KMI Research FTTP article
• FTTH Blog Daily updates on the business and technology of FTTH
• Fiberevolution Frequently updated blog about FTTH and how it will affect business and society
• Kingfisher International Application Notes Fiber Optic Testing information about FTTH backbone Terminology.
• Richardson, TX FTTP Conversion Notes Details of conversion to FTTP in Dallas, TX (USA) suburb of Richardson.
• San Francisco Draft Fiber Study
• UOC University article