Epicyclic gearing

From Wikipedia, the free encyclopedia

Epicyclic gearing is used here to increase output speed. The planet gear carrier (green) is driven by an input torque. The sun gear (yellow) provides the output torque, while the ring gear (red) is fixed. Note the red marks both before and after the input drive is rotated 45° clockwise.
Epicyclic gearing is used here to increase output speed. The planet gear carrier (green) is driven by an input torque. The sun gear (yellow) provides the output torque, while the ring gear (red) is fixed. Note the red marks both before and after the input drive is rotated 45° clockwise.

Epicyclic gearing or planetary gearing is a gear system that consists of one or more outer gears, or planet gears, revolving about a central, or sun gear. Typically, the planet gears are mounted on a movable arm or carrier which itself may rotate relative to the sun gear. Epicyclic gearing systems may also incorporate the use of an outer ring gear or annulus, which meshes with the planet gears.

Contents

[edit] Gear ratio

The carrier (green) is held stationary while the sun gear (yellow) is used as input. The planet gears (blue) turn in a ratio determined by the number of teeth in each gear. Here, the ratio is -24/16, or -3/2; each planet gear turns at 3/2 the rate of the sun gear, in the opposite direction.
The carrier (green) is held stationary while the sun gear (yellow) is used as input. The planet gears (blue) turn in a ratio determined by the number of teeth in each gear. Here, the ratio is -24/16, or -3/2; each planet gear turns at 3/2 the rate of the sun gear, in the opposite direction.
Reduction gears on Pratt & Whitney Canada PT6 gas turbine engine.
Reduction gears on Pratt & Whitney Canada PT6 gas turbine engine.

The gear ratio in an epicyclic gearing system is somewhat non-intuitive, particularly because there are several ways in which an input rotation can be converted into an output rotation. The three basic components of the epicyclic gear are:

  • Sun: The central gear
  • Planet carrier: Holds one or more peripheral planet gears, of the same size, meshed with the sun gear
  • Annulus: An outer ring with inward-facing teeth that mesh with the planet gear or gears

In many epicyclic gearing systems, one of these three basic components is held stationary; one of the two remaining components is an input, providing power to the system, while the last component is an output, receiving power from the system. The ratio of input rotation to output rotation is dependent upon the number of teeth in each gear, and upon which component is held stationary.

One situation is when the planetary carrier is held stationary, and the sun gear is used as input. In this case, the planetary gears simply rotate about their own axes at a rate determined by the number of teeth in each gear. If the sun gear has S teeth, and each planet gear has P teeth, then the ratio is equal to -S/P. For instance, if the sun gear has 24 teeth, and each planet has 16 teeth, then the ratio is -24/16, or -3/2; this means that one clockwise turn of the sun gear produces 1.5 counterclockwise turns of the planet gears.

This rotation of the planet gears can in turn drive the annulus, in a corresponding ratio. If the annulus has A teeth, then the annulus will rotate by P/A turns for each turn of the planet gears. For instance, if the annulus has 64 teeth, and the planets 16, one clockwise turn of a planet gear results in 16/64, or 1/4 clockwise turns of the annulus. Extending this case from the one above:

  • One turn of the sun gear results in − S / P turns of the planets
  • One turn of a planet gear results in P / A turns of the annulus

So, with the planetary carrier locked, one turn of the sun gear results in − S / A turns of the annulus.

The annulus may also be held fixed, with input provided to the planetary gear carrier; output rotation is then produced from the sun gear. This configuration will produce an increase in gear ratio, equal to 1+A/S.

These are all described by the equation:

(2 + n)ωa + nωs − 2(1 + n)ωc = 0

where n is the form factor of the planetary gear, defined by:

n = {N_{\rm s} \over N_{\rm p}}

If the annulus is held stationary and the sun gear is used as the input, the planet carrier will be the output. The gear ratio in this case will be 1/(1+A/S). This is the lowest gear ratio attainable with an epicyclic gear train. This type of gearing is sometimes used in tractors and construction equipment to provide high torque to the drive wheels.

More planet and sun gear units can be placed in series in the same ring gear housing (where the output shaft of the first stage becomes the input shaft of the next stage) providing a larger (or smaller) gear ratio. This is the way some automatic transmissions work.

During World War II, a special variation of epicyclic gearing was developed for portable radar gear, where a very high reduction ratio in a small package was needed. This had two outer annular gears, each half the thickness of the other gears. One of these two annular gears was held fixed and had one fewer teeth than did the other. Therefore, several turns of the "sun" gear made the "planet" gears complete a single revolution, which in turn made the rotating annular gear rotate by a single tooth.

The mechanism of a pencil sharpener with stationary annulus and rotating planet carrier as input
The mechanism of a pencil sharpener with stationary annulus and rotating planet carrier as input

[edit] A simpler way to calculate the output RPM from the input RPM

It is first drawn simplified as the sun, a single planet, the ring GEAR, and an arm holding the planet. Any gear can be the input or output, including the arm.

Now, simply plug in the known values and solve for wring:

\frac{N_{\rm sun}}{N_{\rm ring}}=\frac{w_{\rm arm}- w_{\rm ring}}{w_{\rm sun} - w_{\rm arm}}

where N is the number of teeth, w is angular speed of the element (sun, arm, or ring). Since the angular speed and rpm are directly proportional, you can put rpm instead.

One caveat: if the arm is the input or output, say the ring is the output/input instead and reverse the direction (since if the arm moves a certain speed relative to the ring, the ring moves that same speed the other way relative to the arm, and obviously the arm does not have a tooth count to plug in)

To derive this, just imagine the arm is locked, and calculate the gear ratio wring / wsun = Nsun / Nring, then unlock the arm. From the arms reference frame the ratio is always Nsun/Nring, but from your frame all the speeds are increased by the angular velocity of the arm. So to write this relative relationship, you arrive at the equation from above.

Also, make sure Nsun+2Nplanet=Nring where N is the number of teeth. This simply says that the gears will fit, since N is directly proportional to diameter.

[edit] Advantages / Disadvantage

Advantages of planetary gears over parallel axis gears include high power density, large reduction in a small volume, multiple kinematic combinations, pure torsional reactions, and coaxial shafting. Disadvantages include high bearing loads, inaccessibility, and design complexity. [1][2]

[edit] References

  1. ^ Lynwander, P., 1983, Gear Drive Systems: Design and Application. Marcel Dekker, New York
  2. ^ Smith, J. D., 1983, Gears and Their Vibration: A Basic Approach to Understanding Gear Noise. Marcel Dekker, New York and MacMillan, London

[edit] External links


v • d • e
Gears
Gear systems
Gear shapes
Geartooth profiles
Gear mechanics
Examples
See also