Crease (cricket)
From Wikipedia, the free encyclopedia
- For the goalie's crease in hockey, see Goal area.
In the sport of cricket, the crease is the area demarcated by white lines painted or chalked on the field of play.
The term crease is also used to refer to the lines themselves (but only the back edge of the line, i.e. the edge nearest to the wicket at that end, as this is the actual crease), particularly the popping crease. Law 9 of the Laws of Cricket governs the size and position of the crease markings.
Four creases (one popping crease, one bowling crease, and two return creases) are drawn at each end of the pitch, around the two sets of stumps. The batsmen generally play in and run between the areas defined by the creases at each end of the pitch.
Contents |
[edit] Bowling crease
One bowling crease is drawn at each end of the pitch so that the three stumps in the set of stumps at that end of the pitch fall on it (and consequently it is perpendicular to the imaginary line joining the centres of both middle stumps). Each bowling crease should be 8 feet 8 inches (2.64 metres) in length, centred on the middle stump at each end, and each bowling crease terminates at one of the return creases.
The bowling creases lie 22 yards (66 feet or 20.12 m) apart and mark the ends of the pitch, and so may be used to determine whether there is a no ball because a fielder has encroached on the pitch or the wicket-keeper has moved in front of the wicket before they are permitted to do so.
Formerly, part of the bowler's back foot in the delivery stride was required to fall behind the bowling crease to avoid a delivery being a no ball. This rule was replaced by a requirement that the bowler's front foot in the delivery stride must fall behind the popping crease (see below).
[edit] Popping crease
The odd name of the popping crease refers to the early history of the game of cricket, in that batsmen used to have to 'pop' their bats into a small hole that was located in the middle of the crease for a run to count. For a player to run a batsman out he had to pop the ball into the hole before the bat was grounded in it.
One popping crease is drawn at each end of the pitch in front of each of the two sets of stumps. The popping crease must be 4 feet (1.22 m) in front of and parallel to the bowling crease. Although it is considered to have unlimited length, the popping crease must be marked to at least 6 feet (1.83 metres) on either side of the imaginary line joining the centres of the middle stumps.
The popping crease is used in one test of whether the bowler has bowled a no ball. To avoid a no ball, some part of the bowler's front foot in the delivery stride (that is, the stride when he releases the ball) must be behind the popping crease (although the bowler's front foot does not have to be grounded).
[edit] Batsman out of his ground
In addition, the popping crease determines whether a batsman has been stumped or run out. This is described in Laws 29, 38, and 39 of the Laws of cricket.
- If the batsman facing the bowler (the striker) steps in front of the popping crease to play the ball, leaving no part of his anatomy or the bat on the ground behind the crease, and the wicket-keeper (in possession of the ball) is able to remove the bails from the wicket, then the striker is out stumped.
- If a fielder uses the ball to remove the bails from either set of stumps whilst the batsmen are running between the wickets (or otherwise forward of the popping crease during the course of play), then the batsman (striker or non-striker) is out run out.
[edit] Return crease
A return crease is drawn on each side of each set of the stumps, along each side of the pitch (so there are four return creases in all, one on either side of both sets of stumps). The return creases lie perpendicular to the popping crease and the bowling crease, 4 feet 4 inches (1.32 m) either side of and parallel to the imaginary line joining the centres of the two middle stumps. Each return crease terminates at one end at the popping crease but the other end is considered to be unlimited in length and must be marked to a minimum of 8 feet (2.44 m) from the popping crease.
The return creases are primarily used to determine whether the bowler has bowled a no ball. To avoid a no ball, some part of the bowler's back foot in the delivery stride must land within and not touching the return crease.
[edit] Batting crease
The batting crease is nothing but the popping crease on the other side of the pitch with respect to the bowler. It is the crease where the batsman stands while batting.
