Clutch control
From Wikipedia, the free encyclopedia
This article does not cite any references or sources. (June 2008) Please help improve this article by adding citations to reliable sources. Unverifiable material may be challenged and removed. |
This article may require cleanup to meet Wikipedia's quality standards. Please improve this article if you can. (June 2008) |
Clutch control refers to the act of controlling the speed of a car with a manual transmission by partially engaging the clutch plate, using the clutch pedal instead of (or in conjunction with) the accelerator pedal.
Contents |
[edit] Overview
With the clutch pedal completely depressed, there is no direct link between the engine and the driveshaft, so no power can pass from the engine to the driveshaft and wheels. With the pedal entirely released, there is full contact between the engine and the driveshaft, via the clutch plate, which means that the engine can apply power directly to the driveshaft. However, it is possible to have the clutch plate partially engaged, allowing the clutch to slip. As a result, only a fraction of the power from the engine reaches the driveshaft.
[edit] Benefits
There are benefits to the use of clutch control in specific circumstances:
[edit] Low gear and low speed
When a car is in first gear, small variations in engine speed translate to large changes in acceleration and engine braking. However, with a combination of clutch control and careful use of engine speed, a much smoother ride can be achieved - by allowing the clutch to slip, variations in engine revs are not immediately translated into changes in drive shaft rotation speed, but rather the friction on the clutch plate allows the drive shaft to gradually equalize with the speed of the engine.
Once the car reaches a suitable speed, the clutch can be fully engaged and speed can then be controlled either by varying the engine speed or by partially disengaging the clutch again if necessary.
This particular use of clutch control is frequently taught to learner drivers as a way to control acceleration when pulling away from a complete stop or when driving at very slow speeds while minimizing the chance of stalling the engine.
[edit] Uphill start
When pulling away on an uphill slope the chance of stalling the engine is greater, and as a result it can be beneficial to engage the clutch more slowly than normal while revving higher than normal.
[edit] Adverse road conditions
In adverse road conditions, notably snow or ice, it is recommended to pull away in as high a gear as possible to minimize torque on the wheels and thereby maintain traction with the road. Pulling away requires progressively slower engagement of the clutch as the gear increases, and in a high gear it is necessary to engage the clutch slowly to avoid the increased risk of stalling the engine, or, in the case of adverse weather conditions, spinning the wheels.
[edit] Changing from first to second gear under maximum power
As the clutch slips, engine speed is lost but torque is not lost except through the effect of the new engine speed on the engine torque itself. By analogy to electronics, a resistor (clutch) in series with your generator (engine) bleeds off voltage (engine speed) but does not decrease current (torque) to your load until the generator (engine) starts to put out less current (torque) for some reason.
Of course, the preceding analogy only goes so far because a generator has radically different curves from an engine. In most car engines the torque output is higher as the engine speed increases up to 4500RPM or more [1]. So slipping the clutch actually gives you more power to the wheels even though the fraction of power wasted in the clutch increases much faster.
It is not necessary to maintain high engine speed to properly operate a motor vehicle. Any vehicle with a standard transmission can operate with an engine speed slightly above idle when following the proper gear sequence. The clutch can be operated normally with no sacrifice in performance; however, in certain off-road and racing conditions, to attain higher speed and better performance, the practice of clutch control plays an integral part in doing so.
[edit] Balancing the clutch
Normally when a vehicle is stationary on an uphill slope it is necessary to use the handbrake in conjunction with clutch control to prevent the vehicle from rolling backwards when pulling away. However, in situations where the vehicle must be stopped briefly, for example in slow moving traffic, the clutch can be used to balance the uphill force from the engine with the downhill force of gravity. The benefit of this is that there is no need for the hand- or foot-brake, and the driver can pull away more quickly.
[edit] Criticism
Even normal use of clutch control increases the wear (and decreases the lifespan) of the clutch. Excessive use of clutch control or riding the clutch will cause further damage.
[edit] Prolonged use
While the use of clutch control at low speed can be used to obtain greater control of acceleration and engine braking, once a car has picked up sufficient speed the clutch should be fully engaged (pedal released).
[edit] Excessive engine revolutions
Excessively revving the engine while using clutch control, or keeping the clutch partially engaged while accelerating with the gas pedal, can cause unnecessary damage to the clutch.
[edit] Slipping the clutch
Slipping the clutch (sometimes referred to as feathering the clutch) is a term used by automotive enthusiasts to describe when the driver alternately applies and releases the clutch to achieve some movement of the car. It's called slipping because the clutch plate will slip against the flywheel surface when such an action is performed. Slipping the clutch is known to be hard on the clutch surface due to the sliding friction created.
Drivers can frequently be observed slipping the clutch when they are trying to stay stationary on a hill without using neutral and the brake. They apply the clutch to climb a bit, then release to roll back, then apply again, etc. so that the car stays in about the same place. The alternative to this technique of staying stationary on a hill would be to put the vehicle in neutral and apply the brake.
Slipping the clutch is a popular term in drag racing culture and is done when launching a car, usually in a drag race. Some contend that slipping the clutch is the best way to launch a front-wheel drive (FWD) car as it prevents wheel-hop that many FWD cars experience when too much power is put to the front wheels.
[edit] Riding the clutch
In a vehicle with a manual transmission, riding the clutch refers to the practice of needlessly keeping the clutch partially disengaged. This results in the clutch being unable to fully engage with the flywheel and so causes premature wear on the disc.
A common example of riding the clutch is to keep slight continual pressure on the clutch pedal whilst driving, as when a driver habitually rests his/her foot on the clutch pedal instead of on the floorboard or dead pedal. Although this slight pressure is not enough to allow the clutch disc itself to slip, it is enough to keep the release bearing against the release springs. This causes the bearing to remain spinning, which leads to premature bearing failure.
When shifting properly the driver "shifts" to another gear and then releases pressure on the clutch pedal to re-engage the engine to the driveshaft. If the pedal is released quickly, a definite lurch can be felt as the engine and driveshaft re-engage and their speeds equalize. However, if the clutch is released slowly the clutch disc will "slip" against the flywheel; this friction permits the engine a smoother transition to its new rotation speed. Such routine slippage causes wear on the clutch analogous to the wear-and-tear on a brake pad when stopping. Some amount of wear is unavoidable, but with better clutching/shifting technique it can be minimized.
Riding the clutch occurs when the driver doesn't fully release the clutch pedal. This results in the clutch disc slipping against the flywheel and some engine power not being transferred to the drive train and wheels. Most drivers routinely use this inefficiency effectively when driving in reverse (inasmuch as fully engaging the reverse gear results in velocity too great for the short distance traveled) or in stop-and-go traffic (inasmuch as it is then easier to control the throttle and acceleration at very slow speeds).
Riding the clutch should not be confused with 'freewheeling' or 'coasting' where the clutch is pressed down fully allowing the car to roll either downhill or from inertia. While this isn't damaging to the car, it can be considered a dangerous way to drive since one forgoes the ability to quickly accelerate if needed. It is, however, common practice to roll into a parking space or over speed bumps via inertia.
[edit] Sources
- PreludeDriver.com explains slipping the clutch.