Chine (boating)

From Wikipedia, the free encyclopedia

Traditional rounded hull (A), compared to a hard (B) and soft (C) chine hull
Traditional rounded hull (A), compared to a hard (B) and soft (C) chine hull

A chine in boating refers to a relatively sharp angle in the hull, as compared to the rounded bottoms of most traditional boat hulls. The term hard chine indicates an angle with little rounding, where a soft chine would be more rounded, but still involve the meeting of distinct planes. Chine log construction is a method of building hard chine boat hulls. Hard chines are common in plywood hulls, while soft chines are often found on fiberglass hulls.

Contents

[edit] Reasons for chines

The oldest type of engineered boats are dugout canoes, which were built by hollowing out a log. These designs generally had rounded bottoms, which made best use of the round shape of the logs. Traditional planked hulls in most cultures are built by placing wooden planks oriented parallel to the waterflow and attached to bent wooden frames. This also produced a rounded hull, generally with a sharp bottom edge to form the keel. Planked boats were built in this manner for most of history.

The first hulls to start incorporating hard chines were probably shallow draft cargo carrying vessels used on rivers and in canals. The barge and later the scow used a flat bottom and near vertical sides, which provided the maximum cargo carrying capacity (in both space and displacement) available for a given depth of water.

[edit] Sailing scows

The scow in particular, in the form of the scow schooner, was the first significant example of a hard chine sailing vessel. While the squared off scow hulls were ugly to sailors accustomed to the sleek, rounded hulls of the time, a scow could carry far more cargo, and while a laden scow was slow and difficult to sail, when not heavily laden it would keep up with the traditional schooners sailing to windward. While sailing scows had a poor safety reputation, that was due more to their typical cheap construction and tendency to founder in storms. As long as it sailed in the protected inland and coastal waters it was designed to operate in, however, the sailing scow was an efficient and cost effective solution to transporting goods from inland sources to the coast[1]. A good example of this is the gundalow [2].

[edit] Steamboats

Working in the same inland waters as the sailing scows was the later river steamboat. River steamboats were often built using the same hard chined construction methods of the sailing scows, with a flat bottom, hard chine, and nearly vertical sides[3].

[edit] Small boats

The punt is one of the older and simplest hard chine small boats. Consisting usually of a single plank for each side, with a square bow and stern, the punt was in essence a tiny scow. The sides of a punt are vertical, and they were typically propelled along shallow waters with a long pole, a method of propulsion referred to as punting. Punts are generally used for recreation, and are popular with duck hunters for their ability to move about in marshy hunting areas.

[edit] Various types of chine hulls

Different numbers of chines
Different numbers of chines

The simplest type of chine construction would be the single chine "V" shape, with two flat panels joined at the keel (A). This type of hull is among the simplest to build, but due to the lack of stability of a narrow "V" and the lack of freeboard on a wide "V", single chine hulls are generally only seen on multihull sailboats, which often use two deep "V" shaped hulls connected by akas to provide mutual stability.

The two chine hull (B), with a flat bottom and nearly vertical sides, was the first hard chine design to achieve widespread use. This design provides far more stability than the single chine hull, with minimum draft and a large cargo capacity. These characteristics make the two chine hull popular for punts, barges, and the scows.

The three chine hull (C) is probably the most common hard chine hull. Having a shallow "V" in the bottom and near-vertical panels above that, it approximates the shape of traditional rounded hull boats fairly well, and is common even in fiberglass designs where employing chines offers no advantage in construction.

Designs with higher numbers of chines (D), often just called multichine hulls, are also common. Kayaks, in particular, are often composed of many chines, required for the complex shapes needed to provide good performance under various conditions. By increasing the number of chines, the hull can very closely approximate a round bottomed hull.

It is possible to refer to the different hulls by the numbers of the flat panels that make up the boat. Thus A is a two panel boat, B is a three panel boat, C is a four panel boat and D is a six panel boat.

[edit] Constructing a chined hull

Two planks joined by a chine log
Two planks joined by a chine log

Construction of a chined hull is subject to many different parameters than a round hull, both positive and negative:

  • The sharp angles do not favor bent wooden frames
  • The wide, flat panels may be cross-planked, where the planks may run perpendicular to the keel rather than parallel to it
  • Planks may be of any width, not just a width small enough to approximate the curve of the hull, and most planks can be cut with square edges
  • Flat sections do not provide the stiffness of a rounded section

[edit] Plank hulls

The limitations of wood plank construction, the desire to maximize cargo volume, and the quest for fast, easy hull building led to a new type of construction method unique to chined hulls. This new method used wooden supports placed along the chines called chine logs to provide strength where the chines joined. Beams are then attached to the chine log to support planks running parallel to the chine, while cross-planked sections such as a typical scow bottom may be attached directly to the chine log. This method of construction originated with the sailing scow[4] and continues to be used today, primarily in home built boats. Use of a chine log provides some structural support, but most chine log hulls are primarily monocoque in nature, with the hull planking itself bearing most of the structural load.

Chine log construction works best for hulls where the sides join a flat bottom at a right angle, but it can be used for other angles as well with an appropriately angled chine log. Builders of small boats such as punts, where the plank thickness is relatively large compared to the size of the hull, can dispense with the chine log and nail intersecting planks directly into one another.

[edit] Plywood hulls

Plywood offers the builder a better "plank", far wider, thinner, and stronger than a simple wood plank. A chined hull built out of plywood will often be designed to keep most of the joints between the plywood sheets at the chines, thus making the building process easier. While chine logs can be and still are used for plywood boats[5], a more common technique replaces the chine logs with a fiberglass and epoxy fillet joint that provides both connection and stiffness to the joint; this method is most commonly called stitch and glue construction. The result of the stitch and glue operation is a composite "chine log", with a much greater degree of flexibility in curvature and shape than is possible with a wooden chine log.

[edit] Fiberglass hulls

Many home-built fiberglass hulls are built just like plywood hulls; sheets of a core material, often plywood or a synthetic foam, are joined together to form the shape of the hull, and the fiberglass is applied to this core to form the hull. In this case the hull shape is determined by the core materials, so core materials that favor hard chine design will usually result in a hard chine final product.

Commercial fiberglass hulls are molded, and since the fiberglass and resin used have no inherent shapes, the mold can be of just about any shape. However, molds for low production boats are often made of plywood, and so the properties of the plywood often result in a chined hull. Hard chines may be rounded off by the addition of filler to the mold to create a fillet; this creates the soft chines often found on fiberglass boats.

[edit] References

  1. ^ [1]
  2. ^ [2]
  3. ^ [3]
  4. ^ [4]
  5. ^ [5]