Automatic test pattern generation

From Wikipedia, the free encyclopedia

ATPG (acronym for both Automatic Test Pattern Generation and Automatic Test Pattern Generator) is an electronic design automation method/technology used to find an input (or test) sequence that, when applied to a digital circuit, enables testers to distinguish between the correct circuit behavior and the faulty circuit behavior caused by defects. The generated patterns are used to test semiconductor devices after manufacture, and in some cases to assist with determining the cause of failure (failure analysis.[1]) The effectiveness of ATPG is measured by the amount of modeled defects, or fault models, that are detected and the number of generated patterns. These metrics generally indicate test quality (higher with more fault detections) and test application time (higher with more patterns). ATPG efficiency is another important consideration. It is influenced by the fault model under consideration, the type of circuit under test (full scan, synchronous sequential, or asynchronous sequential), the level of abstraction used to represent the circuit under test (gate, register-transistor, switch), and the required test quality.

Contents

[edit] Basics of ATPG

A defect is an error introduced into a device during the manufacturing process. A fault model is a mathematical description of how a defect alters design behavior. A fault is said to be detected by a test pattern if, when applying the pattern to the design, any logic value observed at one or more of the circuit's primary outputs differs between the original design and the design with the fault. The ATPG process for a targeted fault consists of two phases: fault activation and fault propagation. Fault activation establishes a signal value at the fault model site that is opposite of the value produced by the fault model. Fault propagation moves the resulting signal value, or fault effect, forward by sensitizing a path from the fault site to a primary output.

ATPG can fail to find a test for a particular fault in at least two cases. First, the fault may be intrinsically undetectable, such that no patterns exist that can detect that particular fault. The classic example of this is a redundant circuit, designed so that no single fault causes the output to change. In such a circuit, any single fault will be inherently undetectable.

Second, it is possible that a pattern(s) exist, but the algorithm cannot find it. Since the ATPG problem is NP-complete (by reduction from the boolean satisfiability problem) there will be cases where patterns exist, but ATPG gives up since it will take an incredibly long time to find them (assuming P≠NP, of course).

[edit] The Stuck-at fault model

In the past several decades, the most popular fault model used in practice is the single stuck-at fault model. In this model, one of the signal lines in a circuit is assumed to be stuck at a fixed logic value, regardless of what inputs are supplied to the circuit. Hence, if a circuit has n signal lines, there are potentially 2n stuck-at faults defined on the circuit, of which some can be viewed as being equivalent to others. The stuck-at fault model is a logical fault model because no delay information is associated with the fault definition. It is also called a permanent fault model because the faulty effect is assumed to be permanent, in contrast to intermittent faults which occur (seemingly) at random and transient faults which occur sporadically, perhaps depending on operating conditions (e.g. temperature, power supply voltage) or on the data values (high or low voltage states) on surrounding signal lines. The single stuck-at fault model is structural because it is defined based on a structural gate-level circuit model.

A pattern set with 100% stuck-at fault coverage consists of tests to detect every possible stuck-at fault in a circuit. 100% stuck-at fault coverage does not necessarily guarantee high quality, since faults of many other kinds -- such as bridging faults, opens faults, and transition (aka delay) faults -- often occur.

[edit] Sequential ATPG

Sequential-circuit ATPG searches for a sequence of vectors to detect a particular fault through the space of all possible vector sequences. Various search strategies and heuristics have been devised to find a shorter sequence and/or to find a sequence faster. However, according to reported results, no single strategy/heuristic out-performs others for all applications/circuits. This observation implies that a test generator should include a comprehensive set of heuristics.

Even a simple stuck-at fault requires a sequence of vectors for detection in a sequential circuit. Also, due to the presence of memory elements, the controllability and observability of the internal signals in a sequential circuit are in general much more difficult than those in a combinational circuit. These factors make the complexity of sequential ATPG much higher than that of combinational ATPG.

Due to the high complexity of the sequential ATPG, it remains a challenging task for large, highly sequential circuits that do not incorporate any Design For Testability (DFT) scheme. However, these test generators, combined with low-overhead DFT techniques such as partial scan, have shown a certain degree of success in testing large designs. For designs that are sensitive to area and/or performance overhead, the solution of using sequential-circuit ATPG and partial scan offers an attractive alternative to the popular full-scan solution, which is based on combinational-circuit ATPG.

[edit] ATPG and nanometer technologies

Historically, ATPG has focused on a set of faults derived from a gate-level fault model. As design trends move toward nanometer technology, new manufacture testing problems are emerging. During design validation, engineers can no longer ignore the effects of crosstalk and power supply noise on reliability and performance. Current fault modeling and vector-generation techniques are giving way to new models and techniques that consider timing information during test generation, that are scalable to larger designs, and that can capture extreme design conditions. For nanometer technology, many current design validation problems are becoming manufacturing test problems as well, so new fault-modeling and ATPG techniques will be needed.

[edit] Algorithmic methods

Testing very-large-scale integrated circuits with a high fault coverage is a difficult task because of complexity. Therefore many different ATPG methods have been developed to address combinatorial and sequential circuits.

  • Early test generation algorithms such as boolean difference and literal proposition were not practical to implement on a computer.
  • The D Algorithm was the first practical test generation algorithm in terms of memory requirements. The D Algorithm introduced D Notation which continues to be used in most ATPG algorithms.
  • Path-Oriented Decision Making (PODEM) is an improvement over the D Algorithm. PODEM was created in 1981 when shortcomings in D Algorithm became evident when design innovations resulted in circuits that D Algorithm could not realize.
  • Fan-Out Oriented (FAN Algorithm) is an improvement over PODEM. It limits the ATPG search space to reduce computation time and accelerates backtracing.
  • Methods based on Satisfiability are sometimes used to generate test vectors.
  • Pseudorandom test generation is the simplest method of creating tests. It uses a pseudorandom number generator to generate test vectors.

[edit] Relevant Conferences

ATPG is a topic that is covered by several conferences throughout the year. The primary US conferences are the International Test Conference and The VLSI Test Symposium, while in Europe the topic is covered by DATE.

[edit] See also

[edit] References

  • Electronic Design Automation For Integrated Circuits Handbook, by Lavagno, Martin, and Scheffer, ISBN 0-8493-3096-3 A survey of the field, from which the above summary was derived, with permission.
  • (2004) Microelectronics Failure Analysis. Materials Park, Ohio: ASM International. ISBN 0-87170-804-3. 
  • Explanation of D, PODEM and FAN
  1. ^ Crowell, G; Press, R.. "Using Scan Based Techniques for Fault Isolation in Logic Devices". Microelectronics Failure Analysis: pp. 132-8. 

Design For Test Forum for any question related to ATPG : http://dft.semiconductorforums.com

[edit] Further reading

Note: The articles themselves are sometimes available for free on-line (both the IEEE and ACM allow authors to keep copies on their personal web sites.)

Languages