Swage
From Wikipedia, the free encyclopedia
Swaging (pronunciation note below) is a metal-forming technique in which the metal is plastically deformed to its final shape using high pressures, either by pressing or hammering, or by forcing through a die. Swaging differs from forging in that the swaged metal is cold worked, and the output of the swaging operation is usually the finished shape. The term swage can apply to the process of swaging (verb to swage), a die used for swaging (noun swage), or a tool used to swage (noun).
Contents |
[edit] Examples of applications
[edit] Pipes and cables
The most common use of swaging is to attach fittings to pipes or cables (also called wire ropes); the parts loosely fit together, and a mechanical or hydraulic tool compresses and deforms the fitting, creating a permanent joint. Pipe flaring machines are another example.
[edit] Saw blade teeth
In sawmills, a swage is a used to flare large bandsaw teeth, which increases the width of the cut, called the kerf. A clamp attaches a mandrel and die to the tooth and the eccentric die is rotated, swaging the tip. Saw teeth bent in this way are sometimes referred to as being "set".
[edit] Firearms and ammunition
In internal ballistics, swaging describes the process of the bullet entering the barrel and being squeezed to conform to the rifling. Most firearm bullets are made slightly larger than the inside diameter of the barrel, so that they are swaged to engage the rifling and form a tight seal upon firing. Compare to obturate.
In ammunition manufacture, swaged bullets are bullets manufactured by swaging room temperature metals into a die to form it into the shape of a bullet. The other common manufacturing method is casting, which uses molten metals poured into a mold. Since metals expand when heated and contract when cooled, cast bullets must be cast with a mold slightly larger than the desired finish size, so that as the molten metal cools, it will harden at just the right point to shrink to the desired size. In contrast, swaged bullets, since they are formed at the temperature at which they will be used, can be formed in molds of the exact desired size. This means that swaged bullets are generally more precise than cast bullets. The swaging process also leads to fewer imperfections, since voids commonly found in casting would be pressed out in the swaging process.
Individuals who make their own bullets usually cannot afford the expensive hydraulic presses required for swaging bullets, and are thus forced to make cast bullets. To get high precision results, it is common to cast the bullets slightly oversized, then swage the resulting castings through a die to do the final forming. Since the amount of pressure required to size the bullet is far less than that required to form a bullet, a simple mechanical press can be used, often the same press used for handloading ammunition.
[edit] Rubber components with mold bonded metal sleeves
This process provides a more controlled and cost-effective alternative to 'shooting' the rubber part into a metal sleeve, where an intensive and less dependable secondary operation is needed to finish the product. A metal can with a bonding component (such as phosphate) is painted to the inside diameter, and molten rubber is injected into the metal sleeve. This creates a product that when cooled may be swaged to the desired size. The second reason for this is that the product is more reliable, and during the swaging process the rubber is more relaxed when the outside can to which the rubber is bonded has its diameter reduced, changing the springrate (K) values and dampening the co-efficient (C) of the rubber. After swaging, any inconsistencies in the metal and rubber have been minimized.
[edit] Pronunciation note
Swage is most often pronounced /sweidʒ/ (AHD format: swāj), which is attested in AHD[1] and W3NIDU.[2] Another (less common) pronunciation sometimes heard in the metalworking industries is /swɛdʒ/ (AHD format: swĕj)[3] (perhaps influenced by sledge as in sledgehammer).
[edit] See also
[edit] References
- ^ Headword "swage". The American Heritage Dictionary of the English Language, 4th ed. Houghton Mifflin, 2004, 2000.
- ^ Headword "swage." Webster's Third New International Dictionary, Unabridged. Merriam-Webster, 2002. (Online version requires subscription to view.) http://unabridged.merriam-webster.com (Accessed 2007 March 10.)
- ^ Headword "swage." Merriam-Webster Collegiate Dictionary, online version. http://209.161.33.50/dictionary/swage (Accessed 2007 March 10.)
 Metalworking:
|
|
|---|---|
|
Coin die | Coining | Cold rolling | Die | Drawing | Electromagnetic forming | Flypress | Hot rolling | Hydraulic press | Hydroforming | Machine press | Progressive stamping | Progressive die | Punching | Punch press | Rolling | Shear | Sinking | Stamping press | Metal spinning | Swage |
|
|
|
|
|
Casting | CNC | Cutting tools | Drilling and threading | Fabrication | Finishing | Grinding | Jewellery | Lathe (tool) | Machining | Machine tooling | Measuring | Metalworking | Hand tools | Metallurgy | Milling | Occupations | Press tools | Smithing | Terminology | Welding |
|
