IBM 3705 Communications Controller
From Wikipedia, the free encyclopedia
The IBM 3705 Communications Controller was a simple computer which attached to a IBM System/360 or System/370 channel. Its purpose was to connect communication lines to the mainframe. MST components similar to those used in System/370 were used. It was announced in March 1972. It was designed for semiconductor memory which was not ready at the time of announcement. The 3705-I used 1.2 microsecond core storage; the 3705-II used 1.0 microsecond SRAM.
The 3705 normally occupied a single frame two feet wide and three feet deep. Up to three expansion frames could be attached for a theoretical capacity of 352 half-duplex lines and two independent channel adapters.
Contents |
[edit] Purpose
IBM intended it to be used in three ways:
- Emulation of the older IBM 2703 Communications Controller and its predecessors. The relevant software was the Emulation Program or EP.
- Connection of SNA devices to a mainframe. The relevant software was NCP (Network Control Program). When used in this fashion, the 3705 was considered an SNA PU4.
- Combining the two methods above in a configuration called a Partitioned Emulation Program or PEP.
[edit] Architecture
The storage word length was 16-bits. The registers had the same width as the address bus. Their length varied between 16, 18 and 20 bits depending on the amount of storage installed. A particular interrupt level had eight registers. Register zero was the program counter which gave the address of the next instruction to be executed; the other seven were accumulators. The four odd-numbered accumulators could be addressed as eight single-byte accumulators.
Instructions were fairly simple. Most were register-to-register or register-immediate instructions which executed in a single memory cycle. There were eight storage reference instructions which required two or three storage cycles to complete. The only shift capability was to shift right one or to add a register to itself.
Special hardware assisted in the calculation of a cyclic redundancy check for detection of transmission errors. Both CRC-16 CCITT and CRC-16 IBM were supported. Assuming the running value was maintained in storage, the execution time to accumulate one more byte was five storage cycles (three instructions).
Rapid context switching was a design objective. The register file was divided into four sections. The three commonly used interrupt levels and the background level had distinct sets of registers. Therefore entry into most interrupt levels did not require saving the registers of the interrupted program. The infrequently used level which processed program and hardware errors shared registers with the next highest level and thus had to save and restore registers.
The five program levels were:
- Error processing
- Communication line events
- Channel adapter events
- Service requests from other levels
- Background level
The 3705 had a flashing light style control panel which was superior to most other IBM panels of that style. The two unusual (for IBM) features were:
- Storage (and some external registers) could be displayed while the program was executing.
- The hex input switches and the two register-sized displays could be used by the program while the machine was running. This capability derived from the objective of emulating the IBM 2703 which had a fairly rich control panel.
[edit] Peripherals
Three types of peripherals were available: communications scanners, channel adapters and 8" floppy disk (only available in models without a channel adapter). The first Communication Scanner and the first Channel Adapter occupied the same frame as the CCU. Extra peripherals required extra frames.
[edit] Communication Scanners
Three different communication scanners were offered:
The Type 1 Communication Scanner was an entry level device which presented an interrupt on every received bit. Transmission also required an interrupt for every bit. In theory this would have allowed for rather imaginative uses such as Morse Code and connection to devices with unusual framing methods. A maximum of 64 half-duplex lines could be attached. The aggregate bandwidth was restricted to the heavy processing requirements.
The Type II Communication Scanner performed functions similar to a USART. There was an interrupt for every transmitted or received character. Six different asynchronous character formats, two forms of Bisync and HDLC/SDLC were supported. A single scanner could attach up to 96 (64 for the first scanner) half-duplex lines. This is the basis of the theoretical maximum capacity of 352 lines. In practice the limit was lower as a scanner with more than 48 half duplex lines could not support any 9600 bit/s lines.
The Type III Communication Scanner was a high performance device for attachment of Bisync and HDLC/SDLC lines. It operated on entire frames. DMA was used to fetch and store the bytes of a frame. In theory the line attachment capacity was the same as for Type II Communication Scanner (352 line limit). The need to restrict scanner size to 48 lines to support 9600 bit/s was still present. Restricting scanner size to 16 lines allowed line speeds of up to 30,000 bit/s. A scanner size of 8 lines allowed speed of about 60,000 bit/s.
[edit] Maximum Communication Line Connection Estimates
With modem supplied clocking, a single line was limited to 50 kbit/s; with internal clocking the limit was 2400 bit/s.
Aggregate line connection ability was limited by processing speed.
For a Type II Communications Scanner, processing of a received or transmitted character might take fifty storage cycles (forty instructions). In a 3705-II this gives an aggregate capacity of 20,000 bytes/s. This would allow about 160 half-duplex lines running at a mean speed of 120 cps. Alternatively sixteen half-duplex lines running at 1200 cps (9600 bit/s) would be the theoretical limit. IPSANET experience was that six full-duplex 9600 bit/s lines carrying a heavy load was the limit. IBM software may have had superior performance.
For a Type III Communications Scanner DMA processing of a single character for fairly inexpensive. A single storage cycle was required. This would give a theoretical limit of a million cps (eighty 9600 bit/s half-duplex lines). In practice the limit was probably lower as some processing would be required for end of frame. Also if the frame contents were moved about in storage this would require 3.5 storage cycles per byte.
[edit] Channel Adapters
Two types of channel adapter were offered:
Type 1 and Type 4 Channel Adapters were designed for 270x emulation. They recognized up to 256 channel addresses and transferred data in small bursts (four bytes for the Type 1; 32 bytes maximum for the Type 4). The hardware could accept almost all of the 240 possible channel command codes. Software had to analyse the command from the channel and either reject the command or process it according to specific rules. Interrupt processing required about fifty storage cycles to process a four byte transfer. The 3705 could only have a single Type 1 Adapter but two Type 4 Adapters were permitted.
Type 2 and Type 3 Channel Adapters were designed for NCP use only. Only one device address was recognized. Data transfer was via DMA which made the overhead low if large buffers were used. The hardware accepted seven channel commands of which four were completely processed by the adapter. This left a read and two write commands for the software to process. These adapters could be connected to any of the three System/370 channel types but a block multiplexor channel was preferred. The Type 3 Adapter could be simultaneously operational (but not in mid-command) on two different channels which might be connected to different hosts.
[edit] Related Machines
The Amdahl 4705 was compatible and ran about 2.5 times as fast as a comparable 3705-II. The IBM 3704 was an entry level version of the 3705. It was restricted to 26 half duplex lines (assuming Type 2 Scanner). DMA devices were not supported on the 3704. Performance was about the same as a 3705-I.
[edit] Demise
The 3705 was eventually replaced by the 3720 and 3725. The 3745 was similar but not entirely compatible. The 3705 was withdrawn from marketing in December 1985. Hardware maintenance service was withdrawn in January 1999.
