Hot and high

From Wikipedia, the free encyclopedia

In aviation, hot and high refers to very warm climates or very high elevations that may compromise an aircraft's ability to operate safely.

Air density decreases with increasing temperature and altitude. Lower air density reduces the amount of lift generated by the wings of an airplane or the rotors of a helicopter, which may hamper an aircraft's performance, or in some cases, prevent it from becoming airborne at all.

Aviators gauge air density by calculating the density altitude.

Contents 1 Negative effects of hot and high conditions 2 Improving hot and high performance 3 Jet or Rocket Assisted Take Off 4 Specialized aircraft 5 Other uses

[edit] Negative effects of hot and high conditions

• Airplanes require a longer takeoff run, potentially exceeding the amount of available runway.

• Low air density hampers an aircraft's ability to climb. In some cases, an aircraft may be unable to climb rapidly enough to clear terrain surrounding a mountain airport.

• Helicopters may be forced to operate in the shaded portion of the height-velocity diagram in order to become airborne at all. This creates the potential for an uncontrollable descent in the event of an engine failure.

• Some aircraft, particularly light general aviation airplanes and older helicopters, have service ceilings so low that they may stall simply trying to maintain level flight. In some cases, aircraft have landed at high-altitude airports by taking advantage of cold temperatures only to become stranded as temperatures warmed and air density decreased.

[edit] Improving hot and high performance

Some ways to increase aircraft performance in hot and high conditions include:

• Reduce aircraft weight. Weight can be reduced by carrying only enough fuel to reach the destination rather than filling the tanks completely. In some cases, unnecessary equipment can be removed from the aircraft. However, in many cases, the only practical way to adequately reduce aircraft weight is to depart with a smaller passenger, cargo, or weapons load. Consequently, hot and high conditions at the originating airport may prevent a commercial aircraft from operating with a load large enough to be profitable, or may constrain the firepower that a combat aircraft can bring to bear when conducting a long-range airstrike.

• Increase engine power. More powerful engines can improve an airplane's acceleration and reduce its takeoff run. However, more powerful engines are generally larger and heavier and use more fuel during cruise, increasing the fuel load needed to reach the same destination. The added weight of the fuel and engines may negate the potential performance gain, and the added cost of the extra fuel may constrain the profitability of a commercial aircraft.

• Increase the size of the wings. However, larger wings weigh more and increase drag, making the aircraft slower and increasing fuel consumption during cruise.

• Add high-lift devices to the wings. However, these devices typically add weight and mechanical complexity, increasing manufacturing and maintenance costs. Furthermore, some high-lift devices increase drag during cruise.

• Utilize assisted take off devices, such as rockets, to increase lift and acceleration.

[edit] Jet or Rocket Assisted Take Off

Auxiliary rockets and/or jet engines can help a fully-loaded aircraft to take off within the length of the runway. The rockets are usually one-time units that are jettisoned after takeoff. This practice was common in the 1950s and 60s, when the lower levels of thrust from military turbojets was inadequate for takeoff from shorter runways or with very heavy payloads. It is now seldom used, but some variants of the C-130 Hercules can and have used RATO (JATO, if the boosters are jets rather than rockets) in special operations, such as the botched Operation Credible Sport, as well as at airshows featuring the USMC's Fat Albert, a C-130 that demonstrates it's JATO function to the crowd as a part of the Blue Angels routine.

Auxiliary jets and rockets have rarely been used on civil aircraft due to the risk of aircraft damage and loss of control if something were to go wrong during their use.

[edit] Specialized aircraft

Several manufacturers of early jet airliners offered variants optimized for hot and high operations. Such aircraft generally offered the largest wings and/or the most powerful engines in the model lineup coupled with a small fuselage to reduce weight. Some such aircraft include:

• The Boeing 707-220, which was a 707-120 airframe fitted with more powerful Pratt & Whitney JT4A engines, civilian versions of the military J75. The 707-220 had extremely high fuel consumption, and only 5 were built, all for Braniff International Airways. The 707-220 was rendered redundant by the release of the turbofan-powered 707-120B.

• The McDonnell Douglas DC-9-20, which combined the smaller fuselage of the DC-9-10 with the larger wings and more powerful engines of the DC-9-30, and was significantly outsold by both.

• The Convair 880. Although Convair only offered one configuration of this aircraft, it had more power and a smaller fuselage than its competitors from Boeing and Douglas. Convair essentially wagered the success of the entire 880 model line on the appeal of an aircraft optimized for hot and high operations. The wager failed; only 65 880s were sold and Convair's nascent airliner business soon collapsed.

The marketing failure of these airplanes demonstrated that airlines were generally unwilling to accept reduced efficiency at cruise and smaller ultimate load-carrying capacity in return for a slight performance gain at particular airports. Rather than accepting these drawbacks, it was easier for airlines to demand the construction of longer runways, operate with smaller loads as conditions dictated, or simply drop the unprofitable destinations.

Furthermore, as the second generation of jet airliners began to appear in the 1970s, some aircraft were designed to eliminate the need for a special "hot and high" variant- for instance, the Airbus A300 can perform a 15/0 takeoff, where the leading edge slats are adjusted to 15 degrees and the flaps kept retracted. This takeoff technique is only used at hot and high airports, for it enables a higher climb limit weight and improves second segment climb performance.

Most jetliner manufacturers have dropped the "hot and high" variants from their model lineups.

[edit] Other uses

Less formally, "hot and high" can also describe a botched landing approach, where a fixed-wing aircraft is too fast (hot) and too high above the glide path: since the only way to increase the rate of descent is to increase speed, and the aircraft is already too fast, it is unlikely that the approach can be salvaged.