High voltage
From Wikipedia, the free encyclopedia
- For other meanings of the term High voltage see High voltage (disambiguation)
The term high voltage characterizes electrical circuits, in which the voltage used is the cause of particular safety concerns and insulation requirements. High voltage is used in electrical power distribution, in cathode ray tubes, to generate X-rays and particle beams, to demonstrate arcing, for ignition, in photomultiplier tubes, and high power amplifier vacuum tubes.
Contents |
[edit] Definition
The International Electrotechnical Commission and its national counterparts (IEE, IEEE, VDE, etc.) define high voltage circuits as those with more than 1000 V for alternating current and at least 1500 V for direct current, and distinguish it from low voltage (50–1000 V AC or 120–1500 V DC) and extra low voltage (<50 V AC or <120 V DC) circuits.
In the United States 2005 National Electrical Code (NEC), high voltage is any voltage over 600 V (article 490.2). Laypersons may consider household mains circuits (100–250 V AC), which carry the highest and most dangerous voltages they normally encounter, to be high voltage. In digital electronics, a high voltage is the one that represents a logic 1 (1.1–5 V).
[edit] Safety and insurance industry
While voltages within household circuits are capable of delivering fatal shocks and may constitute high-voltage hazards, they are dangerous only if in contact with the body. Standards bodies do not generally refer to household circuits as 'high voltage'.
Various safety and insurance organizations consider anything outside of the ELV range (i.e. greater than 50 V) to be dangerous and in need of regulation. Voltages above this range are capable of producing heart fibrillation if they produce electric currents in body tissues which happen to pass through the chest area. The electrocution danger is mostly determined by the low conductivity of dry human skin. If skin is wet (especially with electrolytes, including sea water) or if there are wounds, or if the voltage is applied to electrodes which penetrate through the skin, then even voltages far below 40 V can be lethally high. On the other hand, voltages above approximately 500 V have a natural defibrillating effect, so sometimes a higher voltage can be safer than a lower voltage, though by no means safe. A DC circuit may be especially dangerous because it will cause muscles to lock around the wire. It has also been noted that accidental contact with high voltage power lines has not always been fatal because sometimes the victim is thrown clear of the power line by the intensity of the arc that is created and has survived, although with extremely severe injuries.
[edit] Sparks in air
The dielectric breakdown strength of dry air, at Standard Temperature and Pressure (STP), between spherical electrodes is approximately 33 kV/cm.[1] This value should be used only as a rough guide since the actual breakdown voltage is highly dependent upon the electrode shape and size. High voltages, i.e. strong electric fields, often produce violet-colored corona discharges in air, as well as visible sparks. Voltages below about 500-700 volts cannot produce easily visible sparks or glows in air at atmospheric pressure, so by this rule these voltages are 'low'. However, under conditions of low atmospheric pressure (such as in high-altitude aircraft), or in an environment of noble gas such as argon, neon, etc., sparks will appear at much lower voltages. 500 to 700 volts is not a fixed minimum for producing spark breakdown, but it is a rule of thumb. For air at STP, the minimum sparkover voltage is around 380 volts.
While lower voltages will not generally jump a gap that is present before the voltage is applied, interrupting an existing current flow often produces a low voltage spark or arc. As the contacts are separated, a few small points of contact become the last to separate. The current becomes constricted to these small hot spots, causing them to become incandescent, so that they emit electrons (through thermionic emission). Even a small 9 V battery can spark noticeably by this mechanism in a darkened room. The ionized air and metal vapour (from the contacts) form plasma, which temporarily bridges the widening gap. If the power supply and load allow sufficient current to flow, a self-sustaining arc may form. Once formed, an arc may be extended to a significant length before breaking the circuit. Attempting to open an inductive load facilitates the formation of an arc since the inductance provides a high voltage pulse whenever the current is interrupted. AC systems make sustained arcing somewhat less likely since the current returns to zero twice per cycle. The arc is extinguished every time the current goes through a zero crossing, and must reignite during the next half cycle in order to maintain the arc.
[edit] Electrostatic devices and phenomena
A high voltage is not necessarily dangerous. The common static electric sparks seen under low-humidity conditions always involve voltage buildups well above 700V. For example, sparks to car doors in winter can involve voltages as high as 20,000V[2]. Also, physics demonstration devices such as Van de Graaff generators and Wimshurst machines can produce voltages approaching one million volts, yet at worst they deliver a brief sting. These devices have a limited amount of stored energy, so the current produced is low and usually for a short time.[3] During the discharge, these machines apply high voltage to the body for only a millionth of a second or less. The discharge may involve extremely high power over very short periods, but in order to produce heart fibrillation, an electric power supply must produce a significant current in the heart muscle continuing for many milliseconds, and must deposit a total energy in the range of at least millijoules or higher. Alternatively, it must deliver enough energy to damage tissue through heating. Since the duration of the discharge is brief, it generates far less heat (spread over time) than a mobile phone.
Note that Tesla coils are a special case, and touching them is not recommended. Among other issues, they have a tendency to arc to their own bottom-end circuitry, which can introduce powerline frequency (50 Hz or 60 Hz, and capable in any case of depolarizing cells and stopping the heart) currents at lethally high voltages to the body.
[edit] Power lines
Electrical transmission and distribution lines for electric power always use voltages significantly higher than 50 volts, so contact with or close approach to the line conductors presents a danger of electrocution. Contact with overhead wires is a frequent cause of injury or death. Metal ladders, farm equipment, boat masts, construction machinery, aerial antennas, and similar objects are frequently involved in fatal contact with overhead wires. Digging into a buried cable can also be dangerous to workers at the excavation site. Digging equipment (either hand tools or machine driven) that contacts a buried cable may energize piping or the ground in the area, resulting in electrocution of nearby workers. Unauthorized persons climbing on power pylons or electrical apparatus are also frequently the victims of electrocution. At very high transmission voltages even a close approach can be hazardous since the high voltage may spark across a significant air gap.
For high voltage and extra-high voltage transmission lines, specially trained personnel use so-called "live line" techniques to allow hands-on contact with energized equipment. In this case the worker is electrically connected to the high voltage line so that he is at the same electrical potential. Since training for such operations is lengthy, and still presents a danger to personnel, only very important transmission lines are the objects of live-line maintenance practices. Outside these specialized situations, one should not assume that being ungrounded allows one to safely touch energized objects; grounding, or arcing to ground, can occur in unexpected ways, and high-frequency currents can cause burns even to an ungrounded person (touching a transmitting antenna is dangerous for this reason, and likewise a high-frequency Tesla Coil can sustain a spark with only one endpoint).
Normally protective equipment on high-voltage transmission lines prevents formation of an unwanted arc, or ensures it is de-energized within tens of milliseconds. Electrical apparatus designed to interrupt high-voltage circuits is designed to safely direct the resulting arc so that it dissipates without damage. High voltage circuit breakers often use a blast of high pressure air, a special dielectric gas (such as SF6 under pressure), or immersion in mineral oil to quench the arc when the high voltage circuit is broken.
[edit] Arc flash hazard
Depending on the short circuit current available at a switchgear line-up, a hazard is presented to maintenance and operating personnel due to the possibility of a high-intensity electric arc. Maximum temperature of an arc can exceed 10,000 kelvin, and the radiant heat, expanding hot air, and explosive vaporization of metal and insulation material can cause severe injury to unprotected workers. Such switchgear line-ups and high-energy arc sources are commonly present in electric power utility substations and generating stations, industrial plants and large commercial buildings. In the United States the National Fire Protection Association, has published a guideline standard NFPA 70E for evaluating and calculating arc flash hazard, and provides standards for the protective clothing required for electrical workers exposed to such hazards in the workplace. And even then still workers must be careful.
[edit] Explosion hazard
Even voltages insufficient to break down air can be associated with enough energy to ignite atmospheres containing flammable gases or vapours, or suspended dust. For example, air containing hydrogen gas or natural gas or gasoline vapor can be ignited by sparks produced by electrical apparatus. Examples of industrial facilities with hazardous areas are petrochemical refineries, chemical plants, grain elevators, and some kinds of coal mines.
Measures taken to prevent such explosions include:
- Intrinsic safety, which is apparatus designed to not accumulate enough stored energy to touch off an explosion
- Increased safety, which applies to devices using measures such as oil-filled enclosures to prevent contact between sparking apparatus and an explosive atmosphere
- Explosion-proof enclosures, which are designed so that an explosion within the enclosure cannot escape and touch off the surrounding atmosphere (this designation does not imply that the apparatus will survive an internal or external explosion).
In recent years standards for explosion hazard protection have become more uniform between European and North American practice. The "zone" system of classification is now used in modified form in U.S. National Electrical Code and in the Canadian electrical code. Intrinsic safety apparatus is now approved for use in North American applications, though the explosion-proof enclosures used in North America are still uncommon in Europe.
[edit] Toxic gases
Electrical discharges, including partial discharge and corona, can produce small quantities of toxic gases, which in a confined space can prove a serious health hazard. These gases include ozone and various oxides of nitrogen.
[edit] Lightning
The largest-scale sparks are those produced naturally by lightning. An average bolt of negative lightning carries a current of 30-to-50 kiloamperes, and transfers a charge of 5 coulombs, and dissipates 500 megajoules of energy (enough to light a 100 watt light bulb for 2 months). However, an average bolt of positive lightning (from the top of a thunderstorm) may carry a current of 300-to-500 kiloamperes, transfer a charge of up to 300 coulombs, have a potential difference up to 1 gigavolt (a billion volts), and may dissipate enough energy to light a 100 watt lightbulb for up to 95 years. A negative lightning stroke typically lasts for only tens of microseconds, but multiple strikes are common. A positive lightning stroke is typically a single event. However, the larger peak current may flow for hundreds of milliseconds, making it considerably hotter and more dangerous than negative lightning.
Hazards due to lightning obviously include a direct strike on persons or property. However, lightning can also create dangerous voltage gradients in the earth and can charge extended metal objects such as telephone cables, fences, and pipelines to dangerous voltages that can be carried many miles from the site of the strike. Although many of these objects are not normally conductive, very high voltage can cause the electrical breakdown of such insulators, causing them to act as conductors. These transferred potentials are dangerous to people, livestock, and electronic apparatus. Lightning strikes also start fires and explosions, which result in fatalities, injuries, and property damage. For example, each year in North America, thousands of forest fires are started by lightning strikes.
Measures to control lightning can mitigate the hazard; these include lightning rods, shielding wires, and bonding of electrical and structural parts of buildings to form a continuous enclosure.
Lightning discharges in the atmosphere of Jupiter are thought to be the source of the planet's powerful radio frequency emissions.
[edit] See also
- Electrical engineering
- Electric power transmission (includes a 'Health concerns' section)
- Lock and tag Safety Procedures (As required by OSHA and NFPA 70E in the USA)
- People : Nikola Tesla, Robert J. Van de Graaff, Thomas Burton Kinraide
- Devices : Tesla Coil, spark gap
- Other: voltage, 25 kV AC
[edit] References
- ^ A. H. Howatson, "An Introduction to Gas Discharges", Pergamom Press, Oxford, 1965, no ISBN - page 67
- ^ John Chubb, "Control of body voltage getting out of a car," IOP Annual Congress, Brighton, 1998
- ^ Van de Graaff Generators Frequently Asked Questions - 1998 William J. Beaty
[edit] External links
- High Voltage Tesla Technology Research & More
- Tesla coil mailing list safety sheet
- Arc Flash Safety
- Arc Flash Resources
- Guidelines, Catalog Standards and codes
