EMC problem (excessive field strength)
From Wikipedia, the free encyclopedia
EMC problems can occur when the system which is being adversely affected is subject to a high field strength due to a radio transmitter. It is important to note that these effects are not due to defects in the transmitter (other than poor RF shielding), transmitter defects such as harmonics are considered in Radio transmitter design. This article is intended to give an overview of the nature of these effects and the methods used to mitigate or eliminate them. The article is ordered mainly by the type of equipment which malfunctions when subject to the strong radio frequency field.
Contents |
[edit] Singing sparks and allied effects
The singing spark can be thought of as the ultimate form of the rusty bolt effect. This is a situation where the output of a transmitter is clean, the receiver is able to reject the transmitter's frequency but some object energised by the RF field is then able to generate harmonics or act as a non-linear mixer which generates intermodulation products.
To solve this the best thing to do is to locate the rusty bolt and either remove it or render it harmless. Possible examples of rusty bolts include the pole holding an aerial, cast iron drainpipes, loose manhole covers and guy wires on radio masts.
[edit] TV and radio equipment
[edit] Common problems
[edit] Motorboating
Motorboating can be seen in radio equipment, it can be regarded as a self inflicted EMC problem. While this idea of self imposed EMC effects could include all manner of unwanted feed back and cross talk effects within an item of equipment, for reasons of bevity no discussion of internal feed back (which does not involve a signal leaving an item of equipment) will be included here.
The best method of curing this defect is to improve the RF shielding and the RF filtering of all power, audio and control leads entering the affected unit.
[edit] Harmonics generated in situ
In situ harmonics occur when an RF current flows through a device, and harmonics are generated due to the non-linear nature of the device. This can be regarded as a rusty bolt effect which exists within the malfunctioning device. A good example of this is the pair of diodes which protect the receivers in many VHF rigs lacking an electromechanical relay to switch between transmit and receive (such as the 144 MHz DJ-F1E) from the transmitter's RF output. In the case of the DJ-F1E, these dioides can create intermodulation products when the radio set is overloaded.
[edit] Reproduction of the signal in an IF stage
It is possible for the unwanted signal to enter an Intermediate frequency stage, and if it falls within the passband of the stage it can cause an unwanted effect. In an AM system it is possible that the unwanted signal will be amplified by the linear stage and appear finally to the detector as if it was a sideband of the carrier, it is possible sometimes for harmonics of a HF transmitter generated within a TV set to enter the video IF (which is at about 30 MHz). These harmonics which enter the TV IF could give similar herring bone pattern effects to those seen when harmonics of the HF transmitter are generated in the front end.
In FM systems where the IF stage gain is very high and the stage is designed to be linear, it is likely that if the unwanted signal is at least 10dB weaker than the wanted signal that the capture effect will result in the receiver ignoring the unwanted signal. If however the unwanted signal is stronger than the wanted signal then it is likely that the receiver will be unable to demodulate the wanted signal. This is related to the normal method of jamming FM systems, to jam a FM signal it is normal to transmit a signal which is 10 dB stronger (at the front end of the target receiver) and is within the plateu of most narrow IF stage.
[edit] Cures
[edit] Braid-breakers
If an electronic device with a long coaxial aerial lead is disturbed by a signal from a HF transmitter then the braid of the coaxial should be considered as a path of entry of RF into the affected device. One additional feature which can assist a braid breaker is the use of a RF ground, a quarter wave length of wire will act as a RF ground even when it goes nowhere. This is because the quarterwave transforms the infinite impedance into a zero impedance. The quaterwave length of wire can be regarded as an artificial earth for RF purposes.
By adding a braid-breaker filter to the system common mode signals will be attenuated while unbalanced signals will be allowed to pass unhindered. This is also something which is added to long leads in military electronic equipment which is intended to continue to function even after being subjected to a nuclear electromagnetic pulse (EMP) and also would increase the likelihood of an electronic device surviving a near-by lightning strike (direct lightning hits are very hard to protect against).
For UHF TV a wide range of good designs exist, these include a ferrite RF choke on the downlead and some networks of passive components.
[edit] RF chokes on leads
This is a well used method for filtering many leads on communication equipment. In common with the braid breaker the intention is to suppress common mode signals. One popular method of making a RF choke is to use a large ferrite bead where the cable passes through the hole. Such chokes can often be seen on the power connection leads of laptops and on the video signal leads of computer monitors.
The addition of RF chokes can often reduce greatly the RF current flowing through a TV set and hence improve the immunity of the installation.
[edit] Filters in the aerial lead
If the receiver's input is routed via a device which rejects the unwanted signals then this additional filtering can improve the imunity of the installation. It is the case that the additional filter will improve the situation. When a transmitter needs to be colocated with a receiver where the frequncy difference is very small (for example 145.000 and 145.600 MHz) the cavity filters can be used on both the transmitter and the receiver to improve the purity of the transmitter and the imunity of the receiver.
One design for VHF/UHF TV which also has the ability to filter out 144 MHz, 432 MHz and 1296 MHz signals has been created by a Russian (UA9FAD).[1]. A design for UHF TV which is designed for the six meter band (50 MHz) has been pubsihed by the UK six meter group. [2]One design for FM radios (band II) has been created by a German (DF9CY) [3]
[edit] Audio equipment
[edit] Different transmitter modes
It is possible for the non-linear circuits within audio equipment to act as an inadvertent radio receiver. In the case of FM transmiters a click may be heard as the RF field appears and also when it disappears.
In the case of amplitude modulation it is possible for the original audio to be recovered by the affected device. AM is still used for longwave and mediumwave broadcasting, and sometimes in communications equipment used by services such as the fire brigade, military or police.
A weird animal quacking or is an unintelligible human voice is likely sign that that the transmitter is using single-sideband modulation. SSB (single side band) tends to be used in applications where long range communication is needed, here the non-linear device is mixng frequencies but because the carrier has been supprressed it is not possible to restore the original audio with such a simple demodulator.
[edit] Stereo leads as a dipole
It is the case that a stereo system with external speaker attached by long leads to the main unit (holding the audio electronics) can be troubled by EMC problems which are caused by the speaker leads acting as a dipole aerial.
One method of curing this is to add a ferrite choke to the speaker leads close to where they enter the main unit.
[edit] Rectification in the audio equipment
According to the RSGB handbook one common way in which stereo systems are affected is when the RF current picked up by the speaker cable, and then flows through the feedback circuit into an early stage in the audio amplifier. The RF is then rectified when it flows through the base/emitter junction of a bipolar transistor. Below is shown a typical audio stage.
[edit] Reference
- Radiocommunication handbook (RSGB), ISBN 0-900612-58-4
- The Radio Amateur's Guide to EMC, Robin Page-Jones (G3JWI) (RSGB), 1992, ISBN 1-872309-16-X
