DVB-T

From Wikipedia, the free encyclopedia

DVB-T stands for Digital Video Broadcasting - Terrestrial and it is the DVB European consortium standard for the broadcast transmission of digital terrestrial television. This system transmits a compressed digital audio/video stream, using OFDM modulation with concatenated channel coding (i.e. COFDM). The adopted source coding methods are MPEG-2 and, more recently, H.264.

In June 2006, a study group named TM-T2 (Technical Module [=group] on Next Generation DVB-T [=DVB-T2]) has been established by DVB Group to develop an advanced modulation scheme that could be adopted by a second generation digital terrestrial television standard [1].

Contents

[edit] Technical description of the transmitter

Scheme of a DVB-T transmission system
Scheme of a DVB-T transmission system

With reference to the figure, a short description of the single processing blocks follows.

  • Source coding and MPEG-2 multiplexing (MUX): compressed video, compressed audio, and data streams are multiplexed into PSs (Programme Streams). One or more PSs are joined together into an MPEG-2 TS (MPEG-2 Transport Stream); this is the basic digital stream which is being transmitted and received by home Set Top Boxes (STB). Allowed bitrates for the transported data depend on a number of coding and modulation parameters: it can range from about 5 to about 32 Mbit/s (see the bottom figure for a complete listing).
  • Splitter: two different TSs can be transmitted at the same time, using a technique called Hierarchical Transmission. It may be used to transmit, for example, a standard definition SDTV signal and a high definition HDTV signal on the same carrier. Generally, the SDTV signal is protected better than the HDTV one. At the receiver, depending on the quality of the received signal, the STB may be able to decode the HDTV stream or, if signal strength lacks, it can switch to the SDTV one (in this way, all receivers that are in proximity of the transmission site can lock the HDTV signal, whereas all the other ones, even the farthest, may still be able to receive and decode a SDTV signal).
  • MUX adaptation and energy dispersal: the MPEG-2 TS is identified as a sequence of data packets, of fixed length (188 bytes). With a technique called energy dispersal, the byte sequence is decorrelated.
  • External encoder: a first level of protection is applied to the transmitted data, using a nonbinary block code, a Reed-Solomon RS (204, 188) code, allowing the correction of up to a maximum of 8 wrong bytes for each 188-byte packet.
  • External interleaver: convolutional interleaving is used to rearrange the transmitted data sequence, such way it becomes more rugged to long sequences of errors.
  • Internal encoder: a second level of protection is given by a punctured convolutional code, which is often denoted in STBs menus as FEC (Forward error correction). There are five valid coding rates: 1/2, 2/3, 3/4, 5/6, and 7/8.
  • Internal interleaver: data sequence is rearranged again, aiming to reduce the influence of burst errors. This time, a block interleaving technique is adopted, with a pseudo-random assignment scheme (this is really done by two separate interleaving processes, one operating on bits and another one operating on groups of bits).
  • Mapper: the digital bit sequence is mapped into a base band modulated sequence of complex symbols. There are three valid modulation schemes: QPSK, 16-QAM, 64-QAM.
  • Frame adaptation: the complex symbols are grouped in blocks of constant length (1512, 3024, or 6048 symbols per block). A frame is generated, 68 blocks long, and a superframe is built by 4 frames.
  • Pilot and TPS signals: in order to simplify the reception of the signal being transmitted on the terrestrial radio channel, additional signals are inserted in each block. Pilot signals are used during the synchronization and equalization phase, while TPS signals (Transmission Parameters Signalling) are used to send the parameters of the transmitted signal and to unequivocally identify the transmission cell. It should be noted that the receiver must be able to synchronize, equalize and decode the signal to gain access to the information held by the TPS pilots. Thus, the receiver must know this information beforehand, and the TPS data is only used in special cases, such as changes in the parameters, resynchronizations, etc.
  • OFDM Modulation: the sequence of blocks is modulated according to the OFDM technique, using 2048, 4096, or 8192 carriers (2k, 4k, 8k mode, respectively).
  • Guard interval insertion: to decrease receiver complexity, every OFDM block is extended, copying in front of it its own end (cyclic prefix). The width of such guard interval can be 1/32, 1/16, 1/8, or 1/4 that of the original block length.
  • DAC and front-end: the digital signal is transformed into an analog signal, with a digital-to-analog converter (DAC), and then modulated to radio frequency (VHF, UHF) by the RF front-end. The occupied bandwidth is designed to accommodate each single DVB-T signal into 6, 7, or 8 MHz wide channels.

Available bitrates for a DVB-T system in 8 MHz channels. All (decimal) values in Mbit/s:

Modulation Coding rate Guard interval
1/4 1/8 1/16 1/32
QPSK 1/2 4.976 5.529 5.855 6.032
2/3 6.635 7.373 7.806 8.043
3/4 7.465 8.294 8.782 9.048
5/6 8.294 9.216 9.758 10.053
7/8 8.709 9.676 10.246 10.556
16-QAM 1/2 9.953 11.059 11.709 12.064
2/3 13.271 14.745 15.612 16.086
3/4 14.929 16.588 17.564 18.096
5/6 16.588 18.431 19.516 20.107
7/8 17.418 19.353 20.491 21.112
64-QAM 1/2 14.929 16.588 17.564 18.096
2/3 19.906 22.118 23.419 24.128
3/4 22.394 24.882 26.346 27.144
5/6 24.882 27.647 29.273 30.160
7/8 26.126 29.029 30.737 31.668

[edit] Technical description of the receiver

The receiving STB adopts techniques which are dual to those ones used in the transmission.

  • Front-end and ADC: the analog RF signal is converted to base-band and transformed into a digital signal, using an analog-to-digital converter (ADC).
  • Time and frequency synchronization: the digital base band signal is searched to identify the beginning of frames and blocks. Eventual problems on the frequency of the components of the signal are corrected, too. The property that the guard interval at the end of the symbol is placed also at the beginning is exploited to find the beginning of a new OFDM symbol. On the other hand, continual pilots (whose value and position is determined in the standard and thus known by the receiver) are used to determine the frequency offset suffered by the signal. This frequency offset might have been caused by Doppler effect, inaccuracies in either the transmitter or receiver clock, and so on.
  • Guard interval disposal: the cyclic prefix is removed.
  • OFDM demodulation
  • Frequency equalization: the pilot signals are used to equalize the received signal.
  • Demapping
  • Internal deinterleaving
  • Internal decoding: it uses the Viterbi algorithm.
  • External deinterleaving
  • External decoding
  • MUX adaptation
  • MPEG-2 demultiplexing and source decoding

[edit] References

  • ETSI Standard: EN 300 744 V1.5.1), Digital Video Broadcasting (DVB); Framing structure, channel coding and modulation for digital terrestrial television, download from ETSI.

[edit] See also

[edit] External links

Retrieved from "http://en.wikipedia.org../../../d/v/b/DVB-T_5b45.html"