TDLAS

From Wikipedia, the free encyclopedia

TDLAS, an acronym for Tunable Diode Laser Absorption Spectroscopy, is a technique for measuring the concentration of certain species such as methane, water vapor and many more, in a gaseous mixture. The advantage of TDLAS over other techniques for concentration measurement is its ability to achieve very low detection limits (of the order of ppbv). Apart from concentration, it is also possible to determine the temperature, pressure, velocity and mass flux of the gas under observation.

Sometimes TDLAS may refer to Tunable Diode Laser Atomic Absorption Spectroscopy, a technique used in plasma diagnostic. Here the TDLAS technique is used for measurement of metastable atom densities or neutral atom temperature and for identification of small amounts of impurities in plasmas. It is, also, possible to correlate the metastable atom densities with the partial pressure of a particularly gas in various gases mixture plasma. The main benefit of this method compared to optical emission methods is the exclusion of spectral lines enlargement due to optical instruments used, because, this width is much smaller than Doppler width – it is about the same order as natural width (about 1 MHz).

1 Working
2 Basic Principles
3 Applications
4 See also
5 External links

[edit] Working

TDLAS is a simple technique. A basic TDLAS setup consists of tunable diode laser light source, transmitting (i.e. beam shaping) optics, optically accessible absorbing medium, receiving optics and detector/s. The emission wavelength of the tunable diode laser, viz. VCSEL, DFB, etc., is tuned over the characteristic absorption lines of a species in the gas in the path of the laser beam. This causes a reduction of the measured signal intensity, which can be detected by a photodiode, and then used to determine the gas concentration and other properties as described later.

Different diode lasers are used based on the application and the range over which tuning is to be performed. Typical examples are InGaAsP/InP (tunable over 900nm to 1.6 µm), InGaAsP/InAsP (tunable over 1.6 µm to 2.2 µm), etc. These lasers can be tuned by either adjusting their temperature or by changing injection current density into the gain medium. While temperature changes allow tuning over ~100 $cm - 1$ , it is limited by slow tuninng rates ~few Hz, due to the thermal inertia of the system. On the other hand, adjusting the injection current can provide tuning at rates as high as ~10 GHz, but it is restricted to a smaller range ( ~1 - 2 $cm - 1$ ) over which the tuning can be performed. The typical laser linewidth is of the order of $10 - 3 cm - 1$ or smaller.

[edit] Basic Principles

[edit] Concentration Measurement

The basic principle behind the TDLAS technique is simple. The focus here is on a single absorption line in the absorption spectrum of the a particular species of interest. To start with the wavelength of a diode laser is tuned over a particular absorption line of interest and the intensity of the transmitted radiation is measured. The transmitted intensity can be related to the concentration of the species present by the Beer-Lambert law, which states that when a radiation of wavenumber $(\tilde{\nu})$ passes through an absorbing medium, the intensity variation along the path of the beam is given by,

$I(\tilde{\nu}) = I_{0}(\tilde{\nu}) exp(-\alpha(\tilde{\nu})NL)$

where,

$I(\tilde{\nu})$ is the transmitted intensity of the radiation after it has traversed a distance

L

through the medium,

$I_{0}(\tilde{\nu})$ is the initial intensity of the radiation,

$\alpha(\tilde{\nu})NL = \sigma(\tilde{\nu})N = S(T)\phi(\tilde{\nu}- \tilde{\nu}_{0})$ is the absorbance of the medium,

$\sigma(\tilde{\nu})$ is the absorption cross-section of the absorbing species,

$N \!$ is the number density of the absorbing species,

$S(T) \!$ is the line strength (i.e. the total absorption per molecule) of the absorbing species at temperature

T

$\phi(\tilde{\nu}- \tilde{\nu}_{0})$ is the lineshape function for the particular absorption line. Sometimes also represented by $g(\tilde{\nu}- \tilde{\nu}_{0})$ ,

$\tilde{\nu}_{0}$ is the center frequency of the spectrum.

[edit] Temperature Measurement

The above relation requires that the temperature $T \!$ of the absorbing species is known. However, it is possible to overcome this difficulty and measure the temperature simultaneously. There are number of ways to measure the temperature, a widely applied method, which can measure the temperature simultaneously, uses the fact that the line strength $S(T) \!$ is a function of temperature alone. Here two different absorption lines for the same species are probed while sweeping the laser across the absorption spectrum, the ratio of the integrated absorbance, is then a function of temperature alone.

$R =\left( \frac{S_{1}}{S_{2}}\right)_{T} = \left(\frac{S_{1}}{S_{2}} \right)_{T_0} exp\left[-\frac{hc(E_{1}-E_{2})}{k}\left(\frac{1}{T}-\frac{1}{T_{0}} \right) \right]$

where,

$T_{0} \!$ is some reference temperature at which the line strengths are known,

$\Delta E = (E_{1} - E_{2}) \!$ is the difference in the lower energy levels involved in the transitions for the lines begin probed.

Another way to measure the temperature is by relating the FWHM of the probed absorption line to the Doppler line width of the species at that temperature. This is given by,

$FWHM (\Delta\tilde{\nu}_{D}) = \tilde{\nu}_{0} \sqrt{\frac{8kTln2}{mc^{2}}} = \tilde{\nu}_{0} (7.1623\mbox{x}10^{-7}) \sqrt{\frac{T}{M}}$

where,

$m \!$ is the weight of one molecule of the species, and

$M \!$ is the molecular weight of the species.

Note: In the last expression, $T \!$ is in Kelvins and $M \!$ is in g/mol. However, this method can be used, only when the gas pressure is low (of the order of few mbar). At higher pressures (~ tens of mbar or more), pressure or collisional broadening becomes important and the lineshape is no longer a function of temperature alone.

[edit] Velocity Measurement

The effect of a mean flow of the gas in the path of the laser beam can been seen as a shift in the absorption spectrum, also known as Doppler shift. The shift in the frequency spectrum is related to the mean flow velocity by,

$\Delta\tilde{\nu}_{D} = \frac{V}{c}\tilde{\nu}_{0}cos\theta$

where,

$\theta \!$ is the angle between the flow direction and the laser beam direction.

Note : $\Delta\tilde{\nu}_{D}$ is not same as the one mentioned before where it refers to the width of the spectrum. The shift is usually very small (~ $3x10 - 5 cm - 1 per ms - 1$ for near-IR diode laser) and the shift-to-width ratio is of the order of ~ $10 - 4$ .