Ramus mandibulae

From Wikipedia, the free encyclopedia

Bone: Ramus mandibulae
Figure 1: Mandible. Outer surface. Side view
Figure 2: Mandible. Inner surface. Side view
Gray's subject #44 173

('ramus mandibulæ; perpendicular portion') The ramus of the mandible is quadrilateral in shape, and has two surfaces, four borders, and two processes.

Contents

[edit] Surfaces

The lateral surface [Fig. 1] is flat and marked by oblique ridges at its lower part; it gives attachment throughout nearly the whole of its extent to the masseter.

The medial surface [Fig. 2] presents about its center the oblique mandibular foramen, for the entrance of the inferior alveolar vessels and nerve.

The margin of this opening is irregular; it presents in front a prominent ridge, surmounted by a sharp spine, the lingula mandibulae, which gives attachment to the sphenomandibular ligament; at its lower and back part is a notch from which the mylohyoid groove runs obliquely downward and forward, and lodges the mylohyoid vessels and nerve.

Behind this groove is a rough surface, for the insertion of the internal pterygoid muscle (Pterygoideus internus). The mandibular canal runs obliquely downward and forward in the ramus, and then horizontally forward in the body, where it is placed under the alveoli and communicates with them by small openings.

On arriving at the incisor teeth, it turns back to communicate with the mental foramen, giving off two small canals which run to the cavities containing the incisor teeth.

In the posterior two-thirds of the bone the canal is situated nearer the internal surface of the mandible; and in the anterior third, nearer its external surface.

It contains the inferior alveolar vessels and nerve, from which branches are distributed to the teeth.

[edit] Borders

The lower border of the ramus is thick, straight, and continuous with the inferior border of the body of the bone. At its junction with the posterior border is the angle of the mandible, which may be either inverted or everted and is marked by rough, oblique ridges on each side, for the attachment of the Masseter laterally, and the Pterygoideus internus medially; the stylomandibular ligament is attached to the angle between these muscles. The anterior border is thin above, thicker below, and continuous with the oblique line.

The posterior border is thick, smooth, rounded, and covered by the parotid gland. The upper border is thin, and is surmounted by two processes, the coronoid in front and the condyloid behind, separated by a deep concavity, the mandibular notch.

[edit] Processes

[edit] Coronoid Process

The Temporalis; the zygomatic arch and Masseter have been removed. (Coronoid process labeled at center bottom.)
Enlarge
The Temporalis; the zygomatic arch and Masseter have been removed. (Coronoid process labeled at center bottom.)

The Coronoid Process (processus coronoideus) is a thin, triangular eminence, which is flattened from side to side and varies in shape and size.

Its anterior border is convex and is continuous below with the anterior border of the ramus; its posterior border is concave and forms the anterior boundary of the mandibular notch. Its lateral surface is smooth, and affords insertion to the Temporalis and Masseter.

Its medial surface gives insertion to the Temporalis, and presents a ridge which begins near the apex of the process and runs downward and forward to the inner side of the last molar tooth.

Between this ridge and the anterior border is a grooved triangular area, the upper part of which gives attachment to the Temporalis, the lower part to some fibers of the Buccinator.

[edit] Condyloid Process

The Condyloid Process (processus condyloideus) is thicker than the coronoid, and consists of two portions: the condyle, and the constricted portion which supports it, the neck.

The condyle presents an articular surface for articulation with the articular disk of the temporomandibular joint; it is convex from before backward and from side to side, and extends farther on the posterior than on the anterior surface.

Its long axis is directed medialward and slightly backward, and if prolonged to the middle line will meet that of the opposite condyle near the anterior margin of the foramen magnum.

At the lateral extremity of the condyle is a small tubercle for the attachment of the temporomandibular ligament.

The neck is flattened from before backward, and strengthened by ridges which descend from the forepart and sides of the condyle.

Its posterior surface is convex; its anterior presents a depression for the attachment of the Pterygoideus externus.

The mandibular notch, separating the two processes, is a deep semilunar depression, and is crossed by the masseteric vessels and nerve.

This article was originally based on an entry from a public domain edition of Gray's Anatomy. As such, some of the information contained herein may be outdated. Please edit the article if this is the case, and feel free to remove this notice when it is no longer relevant.

Facial bones
v  d  e

maxilla: body of maxilla: Incisive fossa | Maxillary sinus | Canine fossa | Infraorbital foramen | Anterior nasal spine | Alveolar canals | Infraorbital canal | Pterygopalatine canal
Zygomatic process | Frontal process (Agger nasi | Anterior lacrimal crest) | Alveolar process | Palatine process (Incisive foramen | Incisive canals | Foramina of Scarpa | Premaxilla | Anterior nasal spine)

lacrimal bone: Posterior lacrimal crest | Lacrimal groove

zygomatic bone: Zygomaticofacial foramen | Zygomaticotemporal foramen | Zygomaticoörbital foramina

palatine bone: Pterygopalatine fossa | Pterygoid fossa | Horizontal plate (Posterior nasal spine) | Perpendicular plate (Pterygopalatine canal | Sphenopalatine foramen | Pyramidal process)
processes (Orbital | Sphenoidal)

mandible: body (Symphysis menti, Mental foramen, Mylohyoid line) | Ramus mandibulae (Mandibular foramen, Mandibular canal, Mandibular notch)

others: nasal bone | inferior nasal conchae (maxillary process) | vomer