Raman scattering
From Wikipedia, the free encyclopedia
Raman scattering or the Raman effect is the inelastic scattering of a photon.
When light is scattered from an atom or molecule, most photons are elastically scattered (Rayleigh scattering). The scattered photons have the same energy (frequency) and, therefore, wavelength, as the incident photons. However, a small fraction of light (approximately 1 in 107 photons) is scattered at optical frequencies different from, and usually lower than, the frequency of the incident photons. In a gas, Raman scattering can occur with a change in vibrational, rotational or electronic energy of a molecule (see energy level). Chemists are concerned primarily with the vibrational Raman effect.
In 1922, Indian physicist Chandrasekhara Venkata Raman published his work on the "Molecular Diffraction of Light," the first of a series of investigations with his collaborators which ultimately led to his discovery on 28 February 1928 of the radiation effect which bears his name. The Raman effect was first reported by C. V. Raman and K. S. Krishnan, and independently by Grigory Landsberg and Leonid Mandelstam in 1928. Raman received the Nobel Prize in 1930 for his work on the scattering of light. In 1998 the Raman Effect was designated a ACS National Historical Chemical Landmark in recognition of its significance as a tool for analyzing the composition of liquids, gases, and solids.[1]
Contents |
[edit] Raman scattering: Stokes and anti-Stokes
The interaction of light with matter in a linear regime allows the absorption or simultaneous emission of light of energy precisely matching the difference in energy levels of the interacting electrons.
The Raman effect corresponds, in perturbation theory, to the absorption and subsequent emission of a photon via an intermediate electron state, having a virtual energy level (see also: Feynman diagram). There are three possibilities :
- no energy exchange between the incident photons and the molecules (and hence no Raman effect)
- energy exchanges occur between the incident photons and the molecules. The energy differences are equal to the differences of the vibrational and rotational energy-levels of the molecule. In crystals only specific phonons are allowed (solutions of the wave equations which do not cancel themselves) by the periodic structure, so Raman scattering can only appear at certain frequencies. For amorphous materials like glasses, more phonons are allowed and thereby the discrete spectral lines become broad.
-
- molecule absorbs energy: Stokes scattering. The resulting photon of lower energy generates a Stokes line on the red side of the incident spectrum.
- molecule loses energy: anti-Stokes scattering. Incident photons are shifted to the blue side of the spectrum, thus generating an anti-Stokes line.
 |
These differences in energy are measured by subtracting the energy of the mono-energetic laser light from the energy of the scattered photons. The absolute value, however, doesn't depend on the process (Stokes or anti-Stokes scattering), because only the energy of the different vibrational levels is of importance. Therefore, the Raman spectrum is symmetric relative to the Rayleigh band. In addition, the intensities of the Raman bands are only dependent on the number of molecules occupying the different vibrational states, when the process began. The Boltzmann distribution teaches us that more molecules occupy the lower energy levels in most cases:
|
Thus the Stokes spectrum is more intense than the anti-Stokes spectrum.
[edit] Distinction with fluorescence
The Raman effect differs from the process of fluorescence. For the latter, the incident light is completely absorbed and the system is transferred to an excited state from which it can go to various lower states only after a certain resonance lifetime. The result of both processes is essentially the same: A photon with the frequency different from that of the incident photon is produced and the molecule is brought to a higher or lower energy level. But the major difference is that the Raman effect can take place for any frequency of the incident light. In contrast to the fluorescence effect, the Raman effect is therefore not a resonant effect.
[edit] Selection rules
The distortion of a molecule in an electric field, and therefore the vibrational Raman cross section, is determined by its polarizability.
A Raman transition from one state to another, and therefore a Raman shift, can occur only when the polarizability changes during the process under consideration (that is, during the vibration or rotation). The key quantity is the derivative of the polarizability with respect to the normal mode excited during the transition.
[edit] Stimulated Raman scattering and Raman amplification
Raman amplification can be obtained by using Stimulated Raman Scattering (SRS), which actually is a combination between a Raman process with stimulated emission. It is interesting for application in telecommunication fibers to amplify inside the standard material with low noise for the amplification process. However the process requires significant power and thus imposes more stringent limits on the material. The amplification band can be up to 100nm broad, depending on the availability of allowed photon states.
[edit] Raman spectrum generation
For high intensity CW (continuous wave) lasers, SRS can be used to produce broad bandwidth spectra. This process can also be seen as a special case of four wave mixing, where the frequencies of the two incident photons are equal and the emitted spectra are found in two bands separated from the incident light by the phonon energies. The initial Raman spectrum is built up with spontaneous emission and is amplified later on. At high pumping levels in long fibers, higher order Raman spectra can be generated by using the Raman spectrum as a new starting point, thereby building a chain of new spectra with decreasing amplitude. The disadvantage of intrinsic noise due to the initial spontaneous process can be overcome by seeding a spectrum at the beginning, or even using a feedback loop like in a resonator to stabilize the process. Since this technology easily fits into the fast evolving fiber optic laser field and there is demand for transversal coherent high intensity light sources (i.e. broadband telecommunication, imaging applications), Raman amplification and spectrum generation might be widely used in the near future.
[edit] Applications
Raman spectroscopy employs the Raman effect for materials analysis. The frequency of light scattered from a molecule may be changed based on the structural characteristics of the molecular bonds. A monochromatic light source (laser) is required for illumination, and a spectrogram of the scattered light then shows the deviations caused by state changes in the molecule.
Raman spectroscopy is also used in combustion diagnostics. Being a completely non-intrusive technique, it permits the detection of the major species and temperature distribution inside combustors and in flames without any perturbation of the (mainly fluid dynamic and reactive) processes examined.
Stimulated Raman transitions are also widely used for manipulating a trapped ion's energy levels, and thus basis qubit states, in ion trap quantum computing.
[edit] See also
- scattering
- Brillouin scattering
- Raman spectroscopy
- nonlinear optics
- fiber amplifier
- List of surface analysis methods
- Raman laser
[edit] References
- "A new radiation", Indian J. Phys., 2 (1928) 387 - http://www.uky.edu/~holler/raman.html
- Herzberg, Spectra of Diatomic Molecules, Litton Educational Publishing, 1950, ISBN 0-442-03385-0, pp. 61ff and 66ff
