Multi-Memory Controller

From Wikipedia, the free encyclopedia

You have new messages (last change).
This article or section does not cite its references or sources.
Please help improve this article by introducing appropriate citations. (help, get involved!) This article has been tagged since November 2006.

Multi-Memory Controllers or Memory Management Controllers[1] (MMC) are different kinds of special chips designed by various video game developers for use in Nintendo Entertainment System (NES) cartridges. These chips extended the capabilities of the original console and made it possible to create NES games with features the original console could not offer.

With the advent of NES emulators, the code written to emulate these chips became known as mappers.

Contents

[edit] List of MMC chips

This is an incomplete list of memory mapping chips. There are many different chips, and many variants on common chip designs, some of which were used infrequently (in some cases, only once).

[edit] MMC1

The MMC1 chip comes in at least five different versions: MMC1A, MMC1B1, MMC1B2, MMC1B3 and MMC1C. The differences between the different versions are slight, mostly owing to savegame memory protection behavior. The MMC1 chip allowed for switching of different memory banks. Program ROM could be selected in 16KB or 32KB chunks, and character ROM could be selected in 4KB or 8KB chunks. An unusual feature of this memory controller was that its input was serial, rather than parallel, so 5 sequential writes (with bit shifting) were needed to send a command to the circuit.[2]

[edit] MMC2

The MMC2 is only used in Mike Tyson's Punch-Out!! and the later rerelease which removed Mike Tyson. A single 8KB bank of program ROM could be selected (with the remaining 24KB locked) and character ROM could be selected in two pairs of 4KB banks, which would be automatically switched when the video hardware attempted to load particular graphic tiles from memory, thus allowing a larger amount of graphics to be used on the screen without the need for the game itself to manually switch them.[3]

[edit] MMC3

The MMC3 chip, soldered onto a ROM chip containing Super Mario Bros. 3
Enlarge
The MMC3 chip, soldered onto a ROM chip containing Super Mario Bros. 3

The MMC3 was Nintendo's most popular MMC chip. It comes in MMC3A, B, and C revisions. The MMC3 added a scanline based IRQ counter to make split screen scrolling easier to perform (mainly to allow the playfield to scroll while the status bar would remain motionless at the top or bottom of the screen), along with two selectable 8KB program ROM banks and two 2KB+four 1KB selectable character ROM banks.[4]

[edit] MMC4

This chip is only used in three games, all of which were released only for the Famicom in Japan. Functionally, it is nearly identical to the MMC2, where the only difference is that the MMC4 switches program ROM in 16KB banks instead of 8KB banks and has support for a battery-backed SRAM to save game data.[5]

[edit] MMC5

MMC5 was Nintendo's largest mapper. It was also the most expensive, making developers avoid it. The chip has 1 KB of extra RAM, extra sound channels (two square waves), supports vertical split screen scrolling, improved graphics capabilities (making 16,384 different tiles available per screen rather than only 256, and allowing each individual tile to have its own color assignment instead of being restricted to one color set per 2x2 tile group), highly configurable program ROM and character ROM bank switching, and a scanline-based IRQ counter.[6]

[edit] MMC6

The MMC6 is similar to the MMC3, with an additional 1 KiB of RAM which can be saved with battery backup.[7]

[edit] Famicom Disk System

  • Manufacturer: Nintendo
  • Games used in: Almana no Kiseki, Ai Senshi Nicol, Bio Miracle Boku Tte Upa, Esper Dream, Exciting Basket, Falsion, Meikyuu Jiin Dababa, Nazo No Kabe, Risa no Yousei Densetsu, Relics - Ankoku Yousai, Big Challenge! Dogfight Spiri, Famicom Tantei Clup Part II, Link no Bouken, Metroid (Japanese Version), Nazo No Murasamejou, Palutena no Kagami, Pro Wrestling, Shin Onigashima, Vs. Excitebike FDS, Yuuyuuki, Zelda no Densetsu, KikiKaiKai

The Famicom Disk System's ASIC was an extended chip, which supports a wavetable sound channel.

[edit] Third-party chips

[edit] VRC6

The VRC6.
Enlarge
The VRC6.

The VRC6 was an advanced MMC chip from Konami, supporting bank switching for both program code and graphics as well as a scanline-based IRQ counter. The chip also contained support for 3 extra sound channels (two square waves and one sawtooth wave). It was used in Akumajou Densetsu (the Japanese version of Castlevania III: Dracula's Curse), while the US version used the MMC5 from Nintendo. Since the NES, unlike the Famicom, did not allow cartridges to add additional sound channels, the soundtrack on the US and European versions had to be rewritten to use the five sound channels built into the NES.[8]

[edit] VRC7

  • Manufacturer: Konami
  • Games used in: Lagrange Point

The VRC7 was a very advanced MMC chip from Konami, not only supporting bank switching and IRQ counting equivalent to the VRC6 but also containing a YM2413 derivative providing 6 channels of FM Synthesis audio. This advanced audio was used only in the Famicom game Lagrange Point; while the Japanese version of Tiny Toon Adventures 2 also used the VRC7, it did not make use of the extended audio.[9]

[edit] NAMCO106

  • Manufacturer: Namco
  • Games used in: Erika to Satoru no Yumebouken, Final Lap, King of Kings, Mappy Kids, Megami Tensei II, Rolling Thunder, Sangokushi 2, Youkai Douchuuki

NAMCO106 was an advanced chip using 4-bit sample table synthesis, that supports up to 8 extra sound channels, with aliasing increasing with the number of active channels.

[edit] FME-7

The FME-7 was a memory mapping circuit developed by Sunsoft for use in NES and Famicom cartridges. It allows the program ROM to be switched in 8KB banks and the character ROM to be switched in 1KB banks. It also contains hardware allowing the cartridge to generate IRQ signals after a specified number of CPU clock cycles, thus enabling split-screen effects with minimal use of processing power. A special version of this mapper, labeled as "SUNSOFT 5" rather than "FME-7", contains sound generation hardware which appears to be a subset of the well-known General Instrument AY-3-8910 (3 square waves). This sound generation hardware was used on only one Famicom title – "Gimmick!"

[edit] References

  1. ^ "Why Game Paks Never Forget" from Nintendo Power
  2. ^ Nintendo MMC1 from NESdevWiki
  3. ^ Nintendo MMC2 from NESdevWiki
  4. ^ Nintendo MMC3 from NESdevWiki
  5. ^ Nintendo MMC4 from NESdevWiki
  6. ^ Nintendo MMC5 from NESdevWiki
  7. ^ Nintendo MMC6 from NESdevWiki
  8. ^ Konami VRC6 from NESdevWiki
  9. ^ Konami VRC7 from NESdevWiki
Retrieved from "http://en.wikipedia.org../../../m/u/l/Multi-Memory_Controller_0662.html"