MIPS architecture
From Wikipedia, the free encyclopedia
MIPS, for Microprocessor without Interlocked Pipeline Stages, is a RISC microprocessor architecture developed by MIPS Technologies. By the late 1990s it was estimated that one in three RISC chips produced were MIPS-based designs.[citation needed]
MIPS designs are used in SGI's computer product line; many embedded systems; Windows CE devices; Cisco routers; and video game consoles like the Nintendo 64 and Sony PlayStation, PlayStation 2, and PlayStation Portable handheld system.
The early MIPS architectures were 32-bit implementations (generally 32-bit wide registers and data paths), while later versions were 64-bit implementations. Five backward-compatible revisions of the MIPS instruction set exist, named MIPS I, MIPS II, MIPS III, MIPS IV, and MIPS 32/64. The latest of these, MIPS 32/64 Release 2, defines a control register set as well as the instruction set. Several "add-on" extensions are also available, including MIPS-3D which is a simple set of floating-point SIMD instructions dedicated to common 3D tasks, MDMX(MaDMaX) which is a more extensive integer SIMD instruction set using the 64-bit floating-point registers, MIPS16 which adds compression to the instruction stream to make programs take up less room (allegedly a response to the Thumb encoding in the ARM architecture), and the recent addition of MIPS MT, new multithreading additions to the system similar to HyperThreading in the Intel's Pentium 4 processors.
Because the designers created such a clean instruction set, computer architecture courses in universities and technical schools often study the MIPS architecture. The design of the MIPS CPU family greatly influenced later RISC architectures such as DEC Alpha.
Contents |
[edit] History
In 1981, a team led by John L. Hennessy at Stanford University started work on what would become the first MIPS processor. The basic concept was to dramatically increase performance through the use of deep instruction pipelines, a technique that was well known, but difficult to implement. Generally a pipeline spreads out the task of running an instruction into several steps, starting work on "step one" of an instruction before the preceding instruction is complete. In contrast, traditional designs of the era waited to complete an entire instruction before moving on, thereby leaving large areas of the CPU idle as the process continued. Moreover, the clock frequency of the entire CPU was dictated by the latency of the entire cycle, rather than by the critical path (i.e. the latency of the pipeline stage taking the longest time to complete).
One major barrier to pipelining was that it required interlocks to be set up to ensure that instructions that took multiple clock cycles to complete would stop the pipeline from loading more data — basically to pause while it completed. These interlocks can take a long time to set up, and were thought to be a major barrier to future speed improvements. A major design aspect of the MIPS design was to demand that all instructions take only one cycle to complete, thereby removing any needs for interlocking.
Although this design eliminated a number of useful instructions, notably things like multiply and divide which would take multiple steps, it was felt that the overall performance of the system would be dramatically improved because the chips could run at much higher clock rates. This ramping of the speed would be difficult with interlocking involved, as the time needed to set up locks is as much a function of die size as clock rate: adding the hardware needed might actually slow down the overall speed.
The elimination of these instructions became a contentious point. Many observers claimed the design (and RISC in general) would never live up to its hype. If one simply replaces the complex multiply instruction with many simpler additions, where is the speed increase? This overly-simple analysis ignored the fact that the speed of the design was in the pipelines, not the instructions.
In 1984 Hennessy was convinced of the future commercial potential of the design, and left Stanford to form MIPS Computer Systems. They released their first design, the R2000, in 1985, improving the design as the R3000 in 1988. These 32-bit CPUs formed the basis of their company through the 1980s, used primarily in SGI's series of workstations. These commercial designs deviated from the Stanford academic research by implementing most of the interlocks in hardware, supplying full multiply and divide instructions (among others).
In 1991 MIPS released the first 64-bit microprocessor, the R4000. However, MIPS had financial difficulties while bringing it to market. The design was so important to SGI, at the time one of MIPS' few major customers, that SGI bought the company outright in 1992 in order to guarantee the design would not be lost. As a subsidiary of SGI, the company became known as MIPS Technologies.
In the early 1990s MIPS started licensing their designs to third-party vendors. This proved fairly successful due to the simplicity of the core, which allowed it to be used in a number of applications that would have formerly used much less capable CISC designs of similar gate count and price -- the two are strongly related; the price of a CPU is generally related to the number of gates and the number of external pins. Sun Microsystems attempted to follow their success by licensing their SPARC core, but it has never been anywhere near as successful. By the late 1990s MIPS was a powerhouse in the embedded processor field, and in 1997 the 48-millionth MIPS-based CPU shipped, making it the first RISC CPU to outship the famous 68k family. MIPS was so successful that SGI spun-off MIPS Technologies in 1998. Fully half of MIPS' income today comes from licensing their designs, while much of the rest comes from contract design work on cores that will then be produced by third parties.
In 1999 MIPS formalized their licensing system around two basic designs, the 32-bit MIPS32 and 64-bit MIPS64. NEC, Toshiba and SiByte (later acquired by Broadcom) each obtained licenses for the MIPS64 as soon as it was announced. Philips, LSI Logic and IDT have since joined them. Success followed success, and today the MIPS cores are one of the most-used "heavyweight" cores in the marketplace for computer-like devices (hand-held computers, set-top boxes, etc.), with other designers fighting it out for other niches. Some indication of their success is the fact that Freescale (spun-off by Motorola) uses MIPS cores in their set-top box designs, instead of their own PowerPC-based cores.
Since the MIPS architecture is licensable, it has attracted several processor start-up companies over the years. One of the first start-ups to design MIPS processors was Quantum Effect Devices (see next section). The MIPS design team that designed the R4300 started the company SandCraft, which designed the R5432 for NEC and later produced the SR7100, one of the first out-of-order execution processors for the embedded market. The original DEC StrongARM team eventually split into two MIPS-based start-ups: SiByte which produced the SB-1250, one of the first high-performance MIPS-based systems-on-a-chip (SOC); while Alchemy Semiconductor (later acquired by AMD) produced the Au-1000 SoC for low-power applications. Lexra used a MIPS-like architecture and added DSP extensions for the audio chip market and multithreading support for the networking market. Due to Lexra not licensing the architecture, two lawsuits were started between the two companies. The first was quickly resolved when Lexra promised not to advertise their processors as MIPS-compatible. The second was protracted, hurt both companies' business, and culminated in MIPS Technologies giving Lexra a free license and a large cash payment.
[edit] CPU family
The first commercial MIPS CPU model, the R2000, was announced in 1985. It added multiple-cycle multiply and divide instructions in a somewhat independent on-chip unit. New instructions were added to retrieve the results from this unit back to the execution core; these result-retrieving instructions were interlocked.
The R2000 could be booted either big-endian or little-endian. It had thirty-two 32-bit general purpose registers, but no condition code register, considering it a potential bottleneck, a feature it shares with the AMD 29000 and the DEC Alpha. Unlike other registers the program counter is not directly accessible.
The R2000 also had support for up to four co-processors, one of which was built into the main CPU and handled exceptions and traps, while the other three were left for other uses. One of these could be filled by the optional R2010 FPU, which had thirty-two 32-bit registers that could be used as sixteen 64-bit registers for double-precision.
The R3000 succeeded the R2000 in 1988, adding 32 kB (soon increased to 64 KB) caches for instructions and data, along with cache coherency support for multi-processor use. While there were flaws in the R3000's multiprocessor support, it still managed to be a part of several successful multiprocessor designs. The R3000 also included a built-in MMU, a common feature on CPUs of the era. The R3000 was the first successful MIPS design in the marketplace, and eventually over 1 million were made. The R3000A, used in the extremely successful Sony PlayStation, was a speed bumped version running at 40 MHz that delivered a performance of 32 VUPs. Like the R2000, the R3000 was paired with the R3010 FPU. Pacemips produced an R3400 and IDT produced R3500, both of them were R3000s with R3010 fpu on a single chip. Toshiba's R3900 was a virtually first SoC for the early Handheld PCs based on the Windows CE.
The R4000 series, released in 1991, extended the MIPS instruction set to a full 64-bit architecture, moved the FPU onto the main die to create a single-chip system, and operated at a radically high internal clock speed (it was introduced at 100 MHz). However, in order to achieve the clock speed the caches were reduced to 8 KB each and took three cycles to access. The high operating frequencies were achieved through the technique of deep pipelining (called super-pipelining at the time). With the introduction of the R4000 a number of improved versions soon followed, including the R4400 of 1993 which included 16 KB caches, largely bug-free 64-bit operation, and a controller for another 1 MB external (level 2) cache.
MIPS, now a division of SGI called MTI, designed the lower-cost R4200, and later the even lower cost R4300, which was the R4200 with a 32-bit external bus. The Nintendo 64 used a NEC VR4300 CPU that was based upon the low-cost MIPS R4300i.[1]
Quantum Effect Devices (QED), a separate company started by refugees from MIPS, designed the R4600 "Orion", the R4700 "Orion", the R4650 and the R5000. Where the R4000 had pushed clock frequency and sacrificed cache capacity, the QED designs emphasized large caches which could be accessed in just two cycles and efficient use of silicon area. The R4600 and R4700 were used in low-cost versions of the SGI Indy workstation as well as the first MIPS based Cisco routers, such as the 36x0 and 7x00-series routers. The R4650 was used in the original WebTV set-top boxes (now Microsoft TV). The R5000 FPU had more flexible single precision floating-point scheduling than the R4000, and as a result, R5000-based SGI Indys had much better graphics performance than similarly clocked R4400 Indys with the same graphics hardware. SGI gave the old graphics board a new name when it was combined with R5000 in order to emphasize the improvement. QED later designed the RM7000 and RM9000 family of devices for embedded markets like networking and laser printers. QED was acquired by the semiconductor manufacturer PMC-Sierra in August 2000, the latter company continuing to invest in the MIPS architecture.
The R8000 (1994) was the first superscalar MIPS design, able to execute two ALU and two memory operations per cycle. The design was spread over six chips: an integer unit (with 16 KB instruction and 16 KB L1 data caches), a floating-point unit, three full-custom secondary cache tag RAMs (two for secondary cache accesses, one for bus snooping), and a cache controller ASIC. The design had two fully pipelined double precision multiply-add units, which could stream data from the 4 MB off-chip secondary cache. The R8000 powered SGI's Power Challenge computer servers in the mid 1990s and later became available in the Power Indigo2 workstation. Its limited integer performance and high cost dampened appeal for most users, although its FPU performance fit scientific users quite well, and the R8000 was in the marketplace for only a year and remains fairly rare.
In 1995, the R10000 was released. This processor was a single-chip design, ran at a faster clock speed than the R8000, and had larger 32 KB primary instruction and data caches. It was also superscalar, but its major innovation was out-of-order execution. Even with a single memory pipeline and simpler FPU, the vastly improved integer performance, lower price, and higher density made the R10000 preferable for most customers.
Recent designs have all been based upon R10000 core. The R12000 used improved manufacturing to shrink the chip and operate at higher clock rates. The revised R14000 allowed higher clock rates with additional support for DDR SRAM in the off-chip cache, and a faster front side bus clocked to 200 MHz for better throughput. Later iterations are named the R16000 and the R16000A and feature increased clock speed, additional L1 cache, and smaller die manufacturing compared with before.
| Model | Frequency [MHz] | Year | Process [µm] | Transistors [millions] | Die size [mm²] | IO Pins | Power [W] | Voltage | Dcache [k] | Icache [k] | Scache [k] |
|---|---|---|---|---|---|---|---|---|---|---|---|
| R2000 | 8-16.7 | 1985 | 2.0 | 0.11 | -- | -- | -- | -- | 32 | 64 | none |
| R3000 | 12-40 | 1988 | 1.2 | 0.11 | 66.12 | 145 | 4 | -- | 64 | 64 | none |
| R4000 | 100 | 1991 | 0.8 | 1.35 | 213 | 179 | 15 | 5 | 8 | 8 | 1024 |
| R4400 | 100-250 | 1992 | 0.6 | 2.3 | 186 | 179 | 15 | 5 | 16 | 16 | 1024 |
| R4600 | 100-133 | 1994 | 0.64 | 2.2 | 77 | 179 | 4.6 | 5 | 16 | 16 | 512 |
| R5000 | 150-200 | 1996 | 0.35 | 3.7 | 84 | 223 | 10 | 3.3 | 32 | 32 | 1024 |
| R8000 | 75-90 | 1994 | 0.5 | 2.6 | 299 | 591 | 30 | 3.3 | 16 | 16 | 1024 |
| R10000 | 150-250 | 1995 | 0.35 | 6.8 | 299 | 599 | 30 | 3.3 | 32 | 32 | 512 |
| R12000 | 270-400 | 1998 | 0.18–0.25 | 6.9 | 204 | 600 | 20 | 4 | 32 | 32 | 1024 |
| R14000 | 500-600 | 2001 | 0.13 | 7.2 | 204 | 527 | 17 | -- | 32 | 32 | 2048 |
| R16000 | 700-800 | 2002 | 0.11 | -- | -- | -- | 20 | -- | 64 | 64 | 4096 |
Note: These specifications are only common processor configurations. Variations exist, especially in Level 2 cache.
[edit] Applications
Among the manufacturers which made computer workstation systems using MIPS processors are SGI, MIPS Computer Systems, Inc., Olivetti, Siemens-Nixdorf, Acer, Digital Equipment Corporation, NEC, and DeskStation. Various operating systems have been ported to the architecture, such as SGI's IRIX, Microsoft's Windows NT (although support for MIPS ended with the release of Windows NT 4.0) and Windows CE, Linux, BSD, UNIX System V, SINIX, MIPS Computer Systems' own RISC/os, and others.
However, use of MIPS as the main processor of computer workstations has declined, and SGI has announced its plans to cease developing high-performance iterations of the MIPS architecture in favor of using Intel IA64-based processors (see "Other models and future plans" section below).
On the other hand, use of MIPS microprocessors in embedded roles is likely to remain common, because of the low power-consumption and heat characteristics of embedded MIPS implementations, the wide availability of embedded development tools for MIPS, as well as experts knowledgeable about the architecture.
[edit] Other models and future plans
Other members of the MIPS family include the R6000, an ECL implementation of the MIPS architecture which was produced by Bipolar Integrated Technology. The R6000 microprocessor introduced the MIPS II instruction set. Its TLB and cache architecture are different from all other members of the MIPS family. The R6000 did not deliver the promised performance benefits, and although it saw some use in Control Data machines, it quickly disappeared from the mainstream market. The PMC-Sierra RM7000 was a version of the R5000 with a built-in 256 kB level 2 cache and a controller for optional level three cache. It was primarily targeted at embedded designs, including SGI's graphics processors and various networking solutions, primarily by Cisco. The R9000 name was never used.
At one time SGI had intended to move off the MIPS platform to the Intel Itanium, and development was to have ended with the R10000. The ever-longer delays in introducing the Itanium meant that the installed base of MIPS-based machines continued to increase. By 1999 it was clear that development had ended too soon, and the R14000 and R16000 were released as a result. SGI had hinted at a more complex R8000 style FPU for later R-series, and also a dual core processor, but SGI's financial troubles and the officially supported use of QuickTransit emulation to run IRIX binaries on Altix have essentially eliminated IRIX/MIPS hardware development.
[edit] Cores
In recent years most of the technology used in the various MIPS generations has been offered as IP-cores (building-blocks) for embedded processor designs. Both 32-bit and 64-bit basic cores are offered, known as the 4K and 5K respectively, and the design itself can be licensed as MIPS32 and MIPS64. These cores can be mixed with add-in units such as FPUs, SIMD systems, various input/output devices, etc.
MIPS cores have been commercially successful, now being used in many consumer and industrial applications. MIPS cores can be found in newer Cisco and Linksys routers, cable modems and ADSL modems, smartcards, laser printer engines, set-top boxes, robots, handheld computers, Sony PlayStation 2 and Sony PlayStation Portable. In cellphone/PDA applications, the MIPS core has been unable to displace the incumbent, competing ARM core.
Examples of MIPS-powered devices: Broadcom BCM5352E - WiFi router processor with 54g WLAN, fast Ethernet, 200 MHz, 16KiB ins. 8KiB data cache, 256B prefetch cache, MMU, 16-bit 100 MHz SDRAM controller, serial/parallel flash, 5-port 100 Mbit/s Ethernet (switch), 16 GPIO, JTAG, 2xUART, 336-ball BGA. BCM 11xx, 12xx, 14xx - 64bit "SiByte" MIPS line.
IDT RC32438, ATI Xilleon, Alchemy Au1000, 1100, 1200, Broadcom Sentry5, Cavium Octeon CN34xx and CN38xx, Infineon Technologies EasyPort, Amazon, ADM5120, WildPass, INCA-IP, INCA-IP2, NEC EMMA and EMMA2, NEC VR4181A, VR4121, VR4122, VR4181A, VR5432, VR5500, Oak Technologies Generation, PMC-Sierra RM11200, QuickLogic QuickMIPS ESP, Toshiba "Donau", Toshiba TMPR492x, TX4925, TX9956, TX7901
[edit] Programming and emulation
There is a freely available "MIPS R2000/R3000 Simulator" called SPIM for several operating systems (specifically Unix or GNU/Linux; Mac OS X; MS Windows 95, 98, NT, 2000, XP; and DOS) which is good for learning MIPS assembly language programming and the general concepts of RISC-assembly language programming: http://www.cs.wisc.edu/~larus/spim.html
A more feature-rich free MIPS emulator is available from the GXemul project (formerly known as the mips64emul project), which emulates not only the various MIPS III and higher microprocessors (from the R4000 through the R10000), but also emulates entire computer systems which use the microprocessors. For example, GXemul can emulate both a DECstation with a MIPS R4400 CPU (and boot to Ultrix), and an SGI O2 with a MIPS R10000 CPU (although the ability to boot Irix is limited), among others, as well as the various framebuffers, SCSI controllers, and the like which comprise those systems.
| service | Trap code | Input | Output | Notes |
|---|---|---|---|---|
| print_int | $v0=1 | $a0= integer to print | prints a0 to standard output | |
| print_string | $v0=4 | $a0= address of first character | prints a character string to standard output | |
| sbrk | $v0=9 | $a0= number of bytes required | $v0= address of allocated memory | Allocates memory from the heap |
[edit] Summary of R3000 instruction set
Instructions are divided into three types: R, I and J. Every instruction starts with a 6-bit opcode. In addition to the opcode, R-type instructions specify three registers, a shift amount field, and a function field; I-type instructions specify two registers and a 16-bit immediate value; J-type instructions follow the opcode with a 26-bit jump target.[2][3]
Register name, number, use, and call conventions:
| Name | Number | Use | Callee must preserve? |
|---|---|---|---|
| $zero | $0 | constant 0 | N/A |
| $at | $1 | assembler temporary | no |
| $v0–$v1 | $2–$3 | Values for function returns and expression evaluation | no |
| $a0–$a3 | $4–$7 | function arguments | no |
| $t0–$t7 | $8–$15 | temporaries | no |
| $s0–$s7 | $16–$23 | saved temporaries | yes |
| $t8–$t9 | $24–$25 | temporaries | no |
| $k0–$k1 | $26–$27 | reserved for OS kernel | no |
| $gp | $28 | global pointer | yes |
| $sp | $29 | stack pointer | yes |
| $fp | $30 | frame pointer | yes |
| $ra | $31 | return address | N/A |
Registers that are preserved across a call are registers that (by convention) will not be changed by a system call or procedure (function) call. For example, $s-registers must be saved to the stack by a procedure that needs to use them, and $sp and $fp are always incremented by constants, and decremented back after the procedure is done with them (and the memory they point to). By contrast, $ra is changed automatically by any normal function call (ones that use jal), and $t-registers must be saved by the program before any procedure call (if the program needs the values inside them after the call).
[edit] Real instructions
These are instructions that have direct hardware implementation, as opposed to pseudoinstructions which are translated into multiple real instructions before being assembled.
The following are the three formats used for the core instruction set:
| Type | -31- format (bits) -0- | |||||
|---|---|---|---|---|---|---|
| R | opcode (6) | rs (5) | rt (5) | rd (5) | shamt (5) | funct (6) |
| I | opcode (6) | rs (5) | rt (5) | immediate (16) | ||
| J | opcode (6) | address (26) | ||||
- CONST denotes a constant ("immediate").
- In the following, the register numbers are only examples, and any other registers can be used in their places.
- All the following instructions are native instructions.
- Opcodes and funct codes are in hexadecimal.
| Category | Name | Instruction syntax | Meaning | Format/opcode/funct | Notes | ||
|---|---|---|---|---|---|---|---|
| Arithmetic | Add | add $1,$2,$3 | $1 = $2 + $3 (signed) | R | 0 | 2016 | adds two registers |
| Add unsigned | addu $1,$2,$3 | $1 = $2 + $3 (unsigned) | R | 0 | 2116 | ||
| Subtract | sub $1,$2,$3 | $1 = $2 - $3 (signed) | R | 0 | 2216 | subtracts two registers | |
| Add immediate | addi $1,$2,CONST | $1 = $2 + CONST (signed) | I | 816 | Used to add constants (and also to copy one register to another "addi $1, $2, 0") | ||
| Add immediate unsigned | addiu $1,$2,CONST | $1 = $2 + CONST (unsigned) | I | 916 | |||
| Multiply | mult $1,$2 | LO = (($1 * $2) << 32) >> 32; HI = ($1 * $2) >> 32; |
R | 0 | 1816 | Multiplies two registers and puts the 64-bit result in two special memory spots - LOW and HI. Alternatively, one could say the result of this operation is: (int HI,int LO) = (64-bit) $1 * $2 . | |
| Divide | div $1, $2 | LO = $1 / $2 HI = $1 % $2 | R | Divides two registers and puts the 32-bit integer result in LO and the remainder in HI.[2] | |||
| Data Transfer | Load address | la $1, Label | $1 = Memory Address | I | Loads the address of a label. | ||
| Load word | lw $1,CONST($2) | $1 = Memory[$s2 + CONST] | I | 2316 | loads the word stored from: ($s2+CONST) and the following 3 bytes. | ||
| Load halfword | lh $1,CONST($2) | $1 = Memory[$s2 + CONST] | I | 2516 | loads the halfword stored from: ($s2+CONST) and the following byte. | ||
| Load byte | lb $1,CONST($2) | $1 = Memory[$s2 + CONST] | I | loads the byte stored from: ($s2+CONST). | |||
| Store word | sw $1,CONST($2) | Memory[$s2 + CONST] = $1 | I | stores a word into: ($s2+CONST) and the following 3 bytes. The order of the operands is a large source of confusion. | |||
| Store half | sh $1,CONST($2) | Memory[$s2 + CONST] = $1 | I | stores the first half of a register (a halfword) into: ($s2+CONST) and the following byte. | |||
| Store byte | sb $1,CONST($2) | Memory[$s2 + CONST] = $1 | I | stores the first fourth of a register (a byte) into: ($s2+CONST). | |||
| Load upper immediate | lui $1,CONST | $1 = CONST << 16 | I | loads a 16-bit immediate operand into the upper 16-bits of the register specified. Maximum value of constant is 216-1 | |||
| Move from high | mfhi $1 | $1 = HI | R | Moves a value from HI to a register. Do not use a multiply or a divide instruction within two instructions of mfhi (that action is undefined because of the MIPS pipeline). | |||
| Move from low | mflo $1 | $1 = LO | R | 0 | 1216 | Moves a value from LO to a register. Do not use a multiply or a divide instruction within two instructions of mflo (that action is undefined because of the MIPS pipeline). | |
| Logical | And | and $1,$2,$3 | $1 = $2 & $3 | R | Bitwise and | ||
| And immediate | andi $1,$2,CONST | $1 = $2 & CONST | I | ||||
| Or | or $1,$2,$3 | $1 = $2 | $3 | R | Bitwise or | |||
| Or immediate | ori $1,$2,CONST | $1 = $2 | CONST | I | ||||
| Exclusive or | xor $1,$2,$3 | $1 = $2 ^ $3 | R | ||||
| Nor | nor $1,$2,$3 | $1 = ~($2 | $3) | R | Bitwise nor | |||
| Set on less than | slt $1,$2,$3 | $1 = ($2 < $3) | R | Tests if one register is less than another. | |||
| Set on less than immediate | slti $1,$2,CONST | $1 = ($2 < CONST) | I | Tests if one register is less than a constant. | |||
| Bitwise Shift | Shift left logical | sll $1,$2,CONST | $1 = $2 << CONST | R | shifts CONST number of bits to the left (multiplies by 2CONST) | ||
| Shift right logical | srl $1,$2,CONST | $1 = $2 >> CONST | R | shifts CONST number of bits to the right - zeros are shifted in (divides by 2CONST). Note that this instruction only works as division of a two's complement number if the value is positive. | |||
| Shift right arithmetic | sra $1,$2,CONST |   |
R | shifts CONST number of bits - the sign bit is shifted in (divides 2's complement number by 2CONST) | |||
| Conditional branch | Branch on equal | beq $1,$2,CONST | if ($1 == $2) go to PC+4+CONST | I | Goes to the instruction at the specified address if two registers are equal. | ||
| Branch on not equal | bne $1,$2,CONST | if ($1 != $2) go to PC+4+CONST | I | Goes to the instruction at the specified address if two registers are not equal. | |||
| Unconditional jump | Jump | j CONST | goto address CONST | J | Unconditionally jumps to the instruction at the specified address. | ||
| Jump register | jr $1 | goto address $1 | R | Jumps to the address contained in the specified register | |||
| Jump and link | jal CONST | $31 = PC + 4; goto CONST | J | For procedure call - used to call a subroutine, $31 holds the return address; returning from a subroutine is done by: jr $31 | |||
NOTE: in the branching and jump instructions, the offset can be replaced by a label present somewhere in the code.
Pseudoinstructions are translated into multiple real instructions (see above) before being assembled.
| Name | instruction syntax | Real instruction translation | meaning |
|---|---|---|---|
| Branch greater than | bgt | if(R[rs]>R[rt]) PC=Label | |
| Branch less than | blt | if(R[rs]<R[rt]) PC=Label | |
| Branch greater than or equal | bge | if(R[rs]>=R[rt]) PC=Label | |
| branch less than or equal | ble | if(R[rs]<=R[rt]) PC=Label | |
| branch greater than unsigned | bgtu | if(R[rs]<=R[rt]) PC=Label | |
| branch greater than zero | bgtz | if(R[rs]<=R[rt]) PC=Label |
[edit] Other instructions
These instructions are to be placed in either the "real instructions" or "pseudoinstructions" sections above.
[edit] Common logical instructions (bitwise)
| addiu $1,$2,100 | $1 = $2 + 100 (unsigned immediate) |
| addu $1,$2,$3 | $1 = $2 + $3 (unsigned) |
| div $1,$2 | HI = $1 % $2 ; LO = $1 / $2 |
| subu $1,$2,$3 | $1 = $2 - $3 (unsigned) |
[edit] Memory to register transfer instructions
| lbu $1,100($2) | loads an unsigned byte |
| lhu $1,100($2) | loads an unsigned halfword |
| lwcz $1,100($2) | loads a word to the "z" coprocessor ("z" is the number of the coprocessor) |
Note that there is no corresponding "load lower immediate" instruction; this can be done by using addi (add immediate, see below) or ori (or immediate) with the register $0 (whose value is always zero). For example, both addi $1, $0, 100 and ori $1, $0, 100 load the decimal value 100 into register $1.
[edit] Register to memory transfer instructions
| swcz $1,100($2) | stores a word from the "z" coprocessor ("z" is the number of the coprocessor). |
[edit] Register to register (move) instructions
| mfcz $1,$c1 | moves a value in the coprocessor register $1 to the main processor register $1 ("z" is the number of the coprocessor) |
| mtcz $1,$c1 | moves a value from the main processor register $1 to the coprocessor register $1 |
| mov.d $fp1,$fp3 | moves a value with double precision from the FPU register $3 to the f.p. register $1 |
| mov.s $fp1,$fp3 | moves a value with single precision from the FPU register $3 to the f.p. register $1 |
(values with double precision use two adjacent FPU registers)
An operation with signed immediates differs from one with unsigned ones in that it does not throw an exception. Subtracting an immediate can be done with adding the negation of that value as the immediate.
[edit] Some other important instructions
- nop (no operation) (machine code 0x00000000, interpreted by CPU as sll $0,$0,0)
- break (breaks the program, used by debuggers)
- syscall (uses for system calls to the operating system)
- a set of FPU-related instructions
- a vast set of virtual instructions, decomposed by the assembler in native instructions
[edit] Notes
- ^ NEC Offers Two High Cost Performance 64-bit RISC Microprocessors
- ^ a b MIPS R3000 Instruction Set Summary
- ^ MIPS Instruction Reference
[edit] Further reading
- Patterson and Hennessy: Computer Organization and Design. The Hardware/Software Interface. Morgan Kaufmann Publishers. ISBN 1-55860-604-1
- Dominic Sweetman: See MIPS Run. Morgan Kaufmann Publishers. ISBN 1-55860-410-3
[edit] See also
- Godson, a MIPS-like processor architecture developed at Chinese Academy of Sciences
[edit] External links
- Patterson & Hennessy - Appendix A (PDF)
- summary of MIPS assembly language
- MIPS reference
- MIPS processor images and descriptions at cpu-collection.de
- A programmed introduction to MIPS assembly
- mips bitshift operators
| RISC |
|---|
| Power Architecture · ARM architecture · DEC Alpha · Atmel AVR · MIPS architecture · PA-RISC · PIC microcontroller · SPARC |
