Flash suppressor

From Wikipedia, the free encyclopedia

Close-up of the flash suppressor on a Sig 550.
Enlarge
Close-up of the flash suppressor on a Sig 550.

A flash suppressor, also known as a flash hider, flash guard, flash eliminator, or flash cone, is a device attached to a rifle or other gun that directs hot escaping gases from the barrel end. It reduces the visibility of the brilliant muzzle flash which occurs upon firing to the shooter and or other individuals.

Muzzle flash is especially visible at night, making it easy to see the location of the shooter, and at the same time interfering with the shooter's night vision. It is caused by incandescence of the expanding gases produced by burning gunpowder. Even during the day, the flash obscures the target view. The birdcage hider on the M16 rifle for example, directs the hot gasses so they do not go directly up.

Two common types of flash suppressors are the duckbill and birdcage suppressors. Duckbill flash suppressors have upper and lower "prongs" and directs gas to the sides. Early Mk 43 and some early M16 models featured this type. One disadvantage is that the prongs can get caught on things. Birdcage types still have prongs, but also feature a ring on the front to prevent obstructions from getting caught between the prongs. Another type of flash suppressor is a flash moderator, such as use on some XM177 models. An example of a cone shaped hider is on the Bren machine gun.

Earlier rifle designs from the 19th century tended to have longer barrels than modern rifles. A side effect of the long barrel is that the gunpowder is completely burnt before the bullet leaves the barrel. However if the same weapon is "cut down", as is common in cavalry and jungle-combat versions, the bullet would often leave the barrel before the powder was completely burnt. In this case the unburnt powder would continue to burn in the air, giving off a bright flash.

When barrel lengths dramatically decreased with the introduction of various assault rifles, this flash became a serious problem. Originally limited to "special purpose" roles, it was now expected that all infantry weapons would have short barrels with this problem, and thereby be of limited use in night combat. Flash suppressors became common on late-World War II and later assault rifle designs, and are almost universal on these weapons today.

It is commonly thought that they are used on military rifles to reduce visibility to the enemy, but the size of a device necessary to completely hide the muzzle flash from an enemy during the night would be prohibitive. Military flash suppressors are designed to reduce the muzzle flash from the shooter to preserve their night vision, usually by directing the incandescent gasses to the sides, away from the line of sight of the shooter. Military forces engaging in night combat are still quite visible, and must move quickly after firing to avoid return fire.

Limiting the amount of powder to what the barrel can burn is one possible solution, but differences between individual cartridges mean that some will always have too much, and the reduced powder load produces a lower projectile velocity. Muzzle flash can also be controlled by using cartridges with a faster-burning gunpowder, so that the propellant gases will already have begun to cool by the time they exit the barrel. Faster-burning powder, however, produce less projectile velocity, which reduces both the accuracy and lethality of the weapon.

Flash suppressors reduce, or in some cases eliminate, the flash by rapidly expanding and cooling the gasses as they leave the end of the barrel. Although the overall amount of burning gunpowder is unchanged, the density and temperature are greatly reduced, as is the brightness of the flash.

A number of different flash hider designs have been used. The simplest is a cone on the end of the barrel, which was used on the late-World War II jungle-combat versions of the Lee-Enfield, the No. 5 variant, intended for use in the Pacific. More modern solutions tend to use a "basket" with several slits or holes cut in it, as seen on the M16 and other small-bore weapons. Cone-shaped flash eliminators are also evident on the Bren LMG and on the turret-mounted aircraft machine guns of British WWII heavy bombers, which were used mostly at night.

Flash hiders are often used as a muzzle brake as well by symmetrically cutting slits near the top, but not the bottom, of the hider, which then provides some down-force on firing as the gasses escape upwards, thereby reducing muzzle climb, as well as dust kick up.

[edit] Legality

[edit] United States

Flash suppressors, and barrel shrouds were seen as 'military' features, and were on the list of Federally defined features that, provided enough features were also present on the semi-automatic rifle, then the rifle was defined as illegal, if manufactured after the effective date of the Federal assault weapons ban that went into effect in 1994 in the United States. Muzzle brakes, on the other hand, were ruled "legal" by the BATF. This meant, in practice, muzzle brakes had to be certified by the BATF to prevent end-users from accidentally violating the law and installing a device that could later be found to be defined legally as being more of a flash suppressor than a muzzle brake, even if marketed and sold as a muzzle brake, if incidental flash suppression was deemed to be 'significant' by the BATF. The Federal laws governing this sunsetted in 2004, and are no longer of concern, except in those few jurisdictions in which specific state laws still retain certain provisions of the earlier and now defunct Federal law.[citation needed]

[edit] See also

In other languages