Antenna tuner

From Wikipedia, the free encyclopedia

An antenna tuner, transmatch, antenna tuning unit, or ATU matches a transceiver with a fixed impedance (typically 50 ohms for modern transceivers) to a load (feed line and antenna) impedance which is unknown, complex or otherwise does not match. This mismatch is usually caused when using a non-resonant antenna, one that is not the correct electrical length as compared to the wavelength of the signal. An ATU allows the use of one antenna for a broad range of frequencies. A tuned antenna is never as good as a naturally resonant antenna due to additional induced losses on the feed line due to the SWR (multiple reflections), and losses in the ATU itself.

Strictly speaking the 'ATU' is only an antenna matching unit, as it is unable to change the resonant frequency of the aerial.

Note that similar matching networks are used in other types of equipment, such as linear amplifiers to transform impedances. See impedance bridging for some details.

Contents 1 Basic principle of the 'wide band' designs 2 Basic principle of the 'narrow band' designs 2.1 How it works 3 Types of 'ATU' 3.1 Ultimate transmatch 3.1.1 Classic circuit 3.1.2 How it works 3.1.3 Pi network 3.2 SPC 4 Connecting an ATU 5 Sources

[edit] Basic principle of the 'wide band' designs

For systems which need to operate over a wide frequency range such as a power amplifier operating over the range 1 MHz to 30 MHz in some solid state designs a series of wide band transformers wound on ferrite cores can be used. This design has the advantage of not requiring any tuning when the operating frequency is changed. This type of design can also be used to match an antenna to a transmission line, it has the advantage of not requiring any tuning but it has the disadvantage of not being capable of fine adjustment. These networks can be used to extend the useful range of a conventional narrow band ATU.

In solid state RF power amp design these networks are useful because MOSFETs and bipolar transistors are designed to operate with low resistance loads. Valved RF amplifiers are very different because the load resistance which a valve is designed to operate with is normally much greater, hence for power designs the circuit designs are often very different.

Below is shown for example an autotransformer which has three identical windings on a ferrite core. If the right hand side is connected to a resistive load of 10 ohms, then at each of the left hand terminals a source of different impedance can be attached.

[edit] Basic principle of the 'narrow band' designs

This basic network is able to act as an impedance transformer. If the output has an impedance consisting of R_load and jX_load, while the input is to be attached to a source which has an impedance of R_source and jX_source.

Then

X_L = {(R_source+jX_source).([R_source+jX_source]-[R_load+jX_load])}^0.5

and

X_C = (R_load+jX_load).{(R_source+jX_source)/([R_load+jX_load]-[R_source+jX_source]}^0.5

In this example circuit X_C and X_L can be swapped. All the ATU circuits below serve to create this network which exists between the systems with different impedances.

For instance if the source has a resistive impedance of 50 ohms while the load has a resistive impedance of 1000 ohms then.

X_L = {(50)([50]-[1000])}^0.5 = (-47500)^0.5 = j 217.94 Ohms

X_C = {1000}{(50)/([1000]-[50])}^0.5

X_C = 1000 x 0.2294 ohms

X_C = 229.4 ohms

If the frequency is 28 MHz then

As X_C = 1/2πfC

then 2πfXc = 1/C

So 1/2πfXc = C = 24.78 pF

While as X_L = 2πfL

then L = X_L/2πf = 1.239 mH

[edit] How it works

A parallel network consisting of a resistive element (1000 Ω) and a reactive element (-j 229.415 Ω) will have the same impedance and power factor as a series network consisting of resistive element (50 Ω) and a reactive element (-j 217.94 Ω). Below are

By adding another element in series which has a reactive impedance of +j 217.94, the impedance is 50 ohms (resistive)

[edit] Types of 'ATU'

[edit] Ultimate transmatch

[edit] Classic circuit

The ultimate transmatch is a rather good circuit with a rather ill advised name, this is because a better transmatch called the SPC (series parallel capacitor) circuit was designed after it. In all these three designs the GND terminal is the terminal where the earth plane (ground plane) of an antenna should be wired while the ANT terminal is where the vertical element of a Marconi aerial should be attached.

[edit] How it works

For example imagine source impedance of 200 ohms and a resistive load of 1000 Ω which is connected via a capacitor (with an impedance of -j 200 Ω to the inductor of the transmatch. Through vector mathematics it is possible to transform this into a parallel network consisting of a resistance of 1040 Ω and a capacitor of admittance 1.9231 x 10^-4 (Xc = 5200 Ω)

In the following calculations all phase angles are expressed in degrees, rather than in radians. Start with the resistive load (R_L) of 1000 Ω which is in series with X_c -j 200 Ω.

Z = (R_L² + X_C²)^0.5 = 1020 Ω

Phase angle (θ) = tan^-1 (X_C²/R_L²) = 11.31

Y = 1/Z = 9.8058 x 10^-4

To convert to a parallel network

X_C' = 1/{Y sin (θ)}

R_L' = 1/{Y cos (θ)} = 1040 Ω

If for a moment the reactive part is ignored, then a 1040 to 200 Ω transformation is needed. According to the equations above an inductor of +j 507.32 Ω is needed. If the effect of the capacitor (from the parallel network) is taken into account then an inductor of +j 462.23 Ω is needed. The system can then be transformed by the mathematics into a series network of 199.9 Ω resistive and +j 409.82 Ω. The mathematics required for this step are very closely related to the above mathematics.

To finish off the ATU a capacitor (-j 409.82) is needed to finish off the network.

[edit] Pi network

This pi network can be used, it has the same function as the ultimate transmatch.

[edit] SPC

[edit] Connecting an ATU

Typically the ATU is connected between the antenna and the radio transmitter or receiver. More specifically, the ATU can be connected between the feedline and the antenna to minimize loss, or between the feedline and the radio for convenience. However, SWR in the feedline must be considered in this second configuration.

It is a common misconception that high standing wave ratio (SWR) in and of itself causes loss. This is not the case. An antenna with a high SWR (e.g. 4:1) when properly configured with a ATU could have only a few percent additional loss compared to a perfectly resonant antenna. The ATU essentially redirects the reflected energy back along the feedline and antenna path. The additional losses come from the inherent losses within the feedline and antenna itself. SWR causes feed line losses to be multiplied. Low loss feedline would have minimal loss when tuned with an ATU whereas a "lossy" feedline/antenna combination of the same SWR could have significant loss.

Without the ATU, SWR from a mismatched antenna could cause reflections of power back into the transmitter, which will cause heating in the transmitter and significant power loss.

[edit] Sources

• ARRL website
• The ARRL Antenna Book
• An introduction to Antenna Theory (BP198), H.C Wright, Bernard Babani, London, 1987.
• Reflections Transmission Lines and Antennas by M. Walter Maxwell, W2DU
• The radio communication handbook (5th ed), RSGB, 1976, ISBN 0-900612-58-4.
• SWDXER ¨The SWDXER¨ - with general SWL information and radio antenna tips.