Air preheater
From Wikipedia, the free encyclopedia
Air preheater is a general term to describe any device designed to heat air before another process (for example combustion in a boiler). This article describes the air preheaters used in steam generators (also commonly called boilers) in fossil fuel power plants for generation of electricity.
The purpose of the air preheater is to recover the heat from the flue gas from the boiler to improve boiler efficiency by burning warm air which increases combustion efficiency, and reducing useful heat lost from the flue. As a consequence, the gases are also sent to the chimney or stack at a lower temperature, allowing simplified design of the ducting and stack. It also allows control over the temperature of gases leaving the stack (to meet emissions regulations, for example).
Contents |
[edit] Different types
For use in steam generators in thermal power stations, there are two types of air preheaters: One is a tubular type built into the boiler flue gas ducting, and the other is a rotating regenerative air preheater (RAPH) known as Ljungstrom® Air Preheater [1]. These may be arranged so the gas flows horizontally or vertically across the axis of rotation.
The other major type of air preheater is the regenerator, found in iron or glass manufacture.
[edit] Tubular type
[edit] Construction features
Tubular preheaters consist of straight tube bundles which pass through the outlet ducting of the boiler and open at each end outside of the ducting. Inside the ducting, the hot furnace gases pass around the preheater tubes, transferring heat from the exhaust gas to the air inside the preheater. Ambient air is forced by a fan through ducting at one end of the preheater tubes and at other end the heated air from inside of the tubes emerges into another set of ducting, which carries it to the boiler furnace for combustion.
[edit] Problems
The ductings for cold and hot air all require additional space and structural supports compared with the Ljungstrom design. Further, due to dust-laden abrasive flue gases, the tubes outside the ducting wear out faster on the side facing the gas current. Many advances have been made to eliminate this problem ceramic and hardened steel have been used to combat erosion. Many new CFB's and BFB's are currently installing tubular air heaters. They offer an advantage to the moving parts of a rotary type. The largest company that solely inspects and repairs tubular air heaters is located in West chicago, Il. Corrosion Monitoring Services [2]
[edit] Ljungstrom® Air Preheater (RAPH)
The rotating design (RAPH) consists of a central rotating element, surrounded by a casing that is divided into two ('bi-sector' type) or three ('tri-sector' type) sectors containing seals around the element which allow the element to rotate through all the sectors, but keep gas leakage between sectors to a minimum, allowing a separate gas path through each sector. Three sector types are the most common in modern power generation facilities. In the tri-sector design the largest sector (usually spanning around half the cross-section of the casing) is connected to the boiler hot gas outlet. The hot exhaust gas flows over the central element, transferring some of its heat to the element, and is then ducted away for further treatment in dust collectors and then expelled from the stack. The second, smaller sector, is fed with ambient air by a fan, which passes over the heated element as it rotates into the sector, and is heated before being carried to the boiler furnace for combustion. The third sector, and of the smallest size, is connected to the primary fan outlet ducting. It's purpose is to heat air, which itself will be used in a heat exchanger to heat the air going to the pulverisers and to carry hot coal air mixture to the boiler burners. The air from the primary air fan heated in the RAPH therefore acts as a heating air to remove the moisture from coal dust, acts as a carrier air for the pulverised coal from pulverisers to boiler burners and also as primary air for combustion.
The rotor itself is the medium of heat transfer in this system, and is usually composed of some form of steel and/or ceramic structure. It rotates quite slowly (around 3-5 RPM) to allow optimum heat transfer first from the hot exhaust gases to the element, then as it rotates, from the element to the cooler air in the other sectors.
[edit] Example of construction
In this design the whole air preheater casing is supported on the boiler supporting structure itself with necessary expansion joints in the ducting.
The vertical rotor is supported on thrust bearings at the lower end and has an oil bath lubrication, cooled by water circulating in coils inside the oil bath. This arrangement is for cooling the lower end of the shaft, as this end of the vertical rotor is on the hot end of the ducting. The top end of the rotor has a simple roller bearing to hold the shaft in a vertical position.
The rotor is built up on the vertical shaft with radial supports and cages for holding the baskets in position. Radial and circumferential seal plates are also provided to avoid leakages of gases or air between the sectors or between the duct and the casing while in rotation.
For on line cleaning of the deposits from the baskets steam jets are provided such that the blown out dust and ash are collected at the bottom ash hopper of the air preheater. This dust hopper is connected for emptying along with the main dust hoppers of the dust collectors.
The rotor is turned by an air driven motor and gearing, and is required to be started before starting the boiler and also to be kept in rotation for some time after the boiler is stopped, to avoid uneven expansion and contraction resulting in warping or cracking of the rotor. The station air is generally totally dry (dry air is required for the instrumentation), so the air used to drive the rotor is injected with oil to lubricate the air motor.
Safety protected inspection windows are provided for viewing the preheater's internal operation under all operating conditions.
The baskets are in the sector housings provided on the rotor and are renewable. The life of the baskets depend on the ash abrasiveness and corrosiveness of the boiler outlet gases.
[edit] Problems
The boiler flue gas contains lot of dust particles (due to high ash content) not contributing towards combustion, such as silica, which cause abrasive wear of the baskets, and may also contain corrosive gases depending on the composition of the coal. For example, Indian coals [3] generally result in high levels of ash, sulphur and silica in the flue gas. The wear of the baskets therefore is generally more than other, cleaner-burning coals.
In this RAPH the dust laden, corrosive boiler gases have to pass between the elements of air preheater baskets. The elements are made up of zig zag corrugated plates pressed into a steel basket giving sufficient annular space in between for the gas to pass through. These plates are corrugated to give more surface area for the heat to be absorbed and also to give it the rigidity for stacking them into the baskets. Hence frequent replacements are called for and new baskets are always kept ready. In the early days, Cor-ten® steel was being used for the elements. Today due to technological advance many manufacturers may use their own patents. Some manufacturers supply different materials for the use of the elements to lengthen the life of the baskets.
In certain cases the unburnt deposits may occur on the air preheater elements causing it to catch fire during normal operations of the boiler, giving rise to explosions inside the air preheater. Sometimes mild explosions may be detected in the control room by variations in the inlet and outlet temperatures of the combustion air.
[edit] Regenerator
A regenerator consists of a brick checkerwork: bricks laid with spaces equivalent to a brick's width between them, so that air can flow relatively easily through the checkerwork. The idea is that as hot exhaust gases flow through the checkerwork, they give up heat to the bricks. The airflow is then reversed, so that the hot bricks heat up the incoming combustion air and fuel. For a glass-melting furnace, a regenerator sits on either side of the furnace, often forming an integral whole. For a blast furnace, the regenerators - commonly called Cowper stoves - sit separate to the furnace; a furnace needs no less than two stoves, but may have three. One of the stoves is 'on gas', receiving hot gases from the furnace top and heating the checkerwork inside, whilst the other is 'on blast', receiving cold air from the blowers, heating it and passing it to the blast furnace.
